2011 INFINITI QX tow

1. Adaptive Front lighting System (AFS)switch* (P. 2-40)
2. Instrument brightness control switch (P. 2-41) 3. TRIP/RESET switch for twin trip odometer
(P. 2-6)
4. Headlight, fog light and turn signal switch — Headlight (P. 2-37)
— Turn signal (P. 2-42)
— Fog light (P. 2-42) 5. Steering-wheel-mounted controls
(left side)
— Audio control steering switch (P. 4-81)
— Hands-Free Phone System switch
(P. 4-96)
6. Trip computer switch (P. 2-27)
7. Wiper and washer switch (P. 2-32)
8. Steering-wheel-mounted controls (right side)
— Cruise control system* (P. 5-37)
— Intelligent Cruise Control (ICC) system*
(P. 5-39)
9. Dynamic driver assistance switch* — Lane Departure Prevention (LDP)
system* (P. 5-20)
— Distance Control Assist (DCA) system*
(P. 5-62)
10. Selector lever (P. 5-15)
11. Four-Wheel Drive (4WD) shift switch* (P. 5-84)/ SNOW mode switch (P. 2-49)/
TOW MODE switch (P. 2-49)/Vehicle
Dynamic Control (VDC) OFF switch
(P. 5-98)
12. Headlight aiming control* (P. 2-39)
13. Power lift gate main switch (P. 3-19)
14. Outside rearview mirror remote control switch (P. 3-28)
SSI0748
COCKPIT
0-6Illustrated table of contents

Indica-tor
light Name Page
Adaptive Front lighting
System (AFS) indicator
light* 2-17
Automatic Transmission
(AT) position indicator
light2-18
Check suspension indica-
tor light
2-18
Cruise indicator light* 2-18
Front passenger air bag
status light2-18
High beam indicator light 2-18
Intelligent Brake Assist
(IBA) off indicator light*2-18
Lane Departure Preven-
tion (LDP) ON indicator
light (green)* 2-19
Indica-
tor
light Name Page
Low beam indicator light 2-19
Malfunction Indicator
Light (MIL)
2-19
Security indicator light 2-20
SNOW mode indicator
light2-20
TOW mode indicator light 2-20
Turn signal/hazard indica-
tor lights2-20
Vehicle Dynamic Control
(VDC) off indicator light2-20
*: if so equipped
0-12Illustrated table of contents

●Disconnect and secure the center seat belt
and tongues into the retractor base. See
“Stowing 3rd row center seat belt” later in
this section.
– Always reconnect the center seat belt when the seat is returned to the upright
position
● Make sure that there are no objects on the
seatback cushion.
Power reclining
Push and hold the rear side of the switch1
beside the 3rd row cup holders until the desired
seatback angle (up to 20 degrees) is obtained.
To move the seatback forward again, push and
hold the front side of the switch
2until the
desired angle is obtained.
WARNING
● After adjustment, check to be sure the seat is
securely locked.
● Do not ride in a moving vehicle when the
seatback is reclined. This can be dangerous.
The shoulder belt will not be against your
body. In an accident, you could be thrown
into it and receive neck or other serious inju-
ries. You could also slide under the lap belt
and receive serious internal injuries.
● For the most effective protection when the
vehicle is in motion, the seat should be up-
right. Always sit well back in the seat with
both feet on the floor and adjust the seat belt
properly. See “PRECAUTIONS ON SEAT BELT
USAGE” later in this section.
SSS1095
Safety — Seats, seat belts and supplemental restraint system1-7

CAUTION
When folding the 2nd row seat for maximum
cargo hauling, be sure that cargo does not con-
tact the center console of the captain’s seat (if
so equipped) to avoid possible damage to the
console.
Stowing 2nd and 3rd row seats
To stow 2nd and 3rd row seats for maximum
cargo capacity:
Manual Operation:
1. Pull lever A or B located on the 2nd rowseat. The seatback folds down and the
seat base will tip forward. See “Entry to
3rd row seat” earlier in this section.
Power Operation:
1. Push and hold the corresponding switchlocated on the instrument panel below the
audio system. The seatback will fold down
and tip forward. See “Entry to 3rd row
seat” earlier in this section. 2. Push the folded seat down until it locks in
position. 3. Fold the 3rd row seat flat using the
switches located in the cargo area. See
“Power folding” earlier in this section.
4. Return 3rd row seats to seating positions by raising the 3rd row seatbacks to an
upright position using the switches. Make
sure the seatback is locked in position.
See “Power folding” earlier in this sec-
tion.
5. Return the 2nd row seat to a seating position by raising the 2nd row seatbacks
to an upright position. Make sure the
seatback is locked in position.
SSS1120SSS1121
Safety — Seats, seat belts and supplemental restraint system1-17

3. Position the lap belt portionlow and snug
on the hips as shown.
4. Pull the shoulder belt portion toward the retractor to take up extra slack. Be sure
the shoulder belt is routed over your
shoulder and across your chest.
The three-point type seat belts have two modes
of operation:
●Emergency Locking Retractor (ELR)
● Automatic Locking Retractor (ALR)
The Emergency Locking Retractor (ELR) mode
allows the seat belt to extend and retract to
allow the driver and passengers some freedom of movement in the seat. The ELR locks the seat
belt when the vehicle slows down rapidly or
during impacts.
The Automatic Locking Retractor (ALR) mode
(child restraint mode) locks the seat belt for
child restraint installation.
When the ALR mode is activated the seat belt
cannot be extended again until the seat belt
tongue is detached from the buckle and fully
retracted. The seat belt returns to the ELR mode
after the seat belt fully retracts. For additional
information, see “CHILD RESTRAINTS” later in
this section.
The ALR mode should be used only for child
restraint installation. During normal seat belt
use by an occupant, the ALR mode should not be
activated. If it is activated, it may cause uncom-
fortable seat belt tension.
WARNING
When fastening the seat belts, be certain that
seatbacks are completely secured in the
latched position. If they are not completely se-
cured, passengers may be injured in an acci-
dent or sudden stop.
Unfastening the seat belts
To unfasten the seat belt, push the button on
the buckle. The seat belt automatically retracts.
Checking seat belt operation
Seat belt retractors are designed to lock seat
belt movement by two separate methods:
●
When the belt is pulled quickly from the
retractor.
● When the vehicle slows down rapidly.
SSS0290SSS0326
Safety — Seats, seat belts and supplemental restraint system1-23

WARNING
●Always fasten the connector tongue and the
seat belt in the order shown.
● Always make sure both the connector
tongue and the seat belt tongue are secured
when using the seat belt or installing a child
restraint. Do not use the seat belt or child
restraint with only the seat belt tongue at-
tached. This could result in serious personal
injury in case of an accident or a sudden
stop. Stowing 3rd row center seat belt :
When folding down the 3rd row seat, the 3rd
center seat belt can be retracted into a stowed
position.
1. Hold the connector tongue1so that the
seat belt does not retract suddenly when
the tongue is released from the connector
buckle. Release the connector tongue by
inserting a suitable tool such as key
A
into the connector buckle.
2. Store the seat belt tongue into the tongue holder
Bfirst2.
3. Store the connector tongue into the re- tractor base
3.
WARNING
Do not unfasten the 3rd center seat belt con-
nector except when folding down the 3rd seat.
SSS0241
SSS1077
Safety — Seats, seat belts and supplemental restraint system1-25

1.If you must install a booster seat in the
front seat, move the seat to the rearmost
position.
2. Position the booster seat on the seat. Only place it in a forward-facing direction.
Always follow the booster seat manufac-
turer’s instructions. 3. The booster seat should be positioned on
the vehicle seat so that it is stable.
If necessary, adjust or remove the head
restraint or headrest to obtain the correct
booster seat fit. If the head restraint or
headrest is removed, store it in a secure
place. Be sure to reinstall the head restraint
or headrest when the booster seat is re-
moved. See “HEAD RESTRAINTS” earlier in
this section or “HEADREST” earlier in this
section for head restraint or headrest ad-
justment, removal and installation informa-
tion. If the seating position does not have an
adjustable head restraint or headrest and it
is interfering with the proper booster seat
fit, try another seating position or a different
booster seat.
4. Position the lap portion of the seat belt
low and snug on the child’s hips. Be sure
to follow the booster seat manufacturer’s
instructions for adjusting the seat belt
routing.
5. Pull the shoulder belt portion of the seat belt toward the retractor to take up extra
slack. Be sure the shoulder belt is posi-
tioned across the top, middle portion of
the child’s shoulder. Be sure to follow the
booster seat manufacturer’s instructions
for adjusting the seat belt routing.
6. Follow the warnings, cautions and in- structions for properly fastening a seat
belt shown in “SEAT BELTS” earlier in this
section.
SSS0640
Front passenger position
LRS0454
Safety — Seats, seat belts and supplemental restraint system1-49

●Tampering with the air bag system may re-
sult in serious personal injury. Tampering
includes changes to the steering wheel and
the instrument panel assembly by placing
material over the steering wheel pad and
above the instrument panel or by installing
additional trim material around the air bag
system.
● Modifying or tampering with the front pas-
senger seat may result in serious personal
injury. For example, do not change the front
seats by placing material on the seat cush-
ion or by installing additional trim material,
such as seat covers, on the seat that is not
specifically designed to assure proper air
bag operation. Additionally, do not stow any
objects under the front passenger seat or the
seat cushion and seatback. Such objects
may interfere with the proper operation of
the occupant classification sensors.
● No unauthorized changes should be made to
any components or wiring of the seat belt
system. This may affect the front air bag
system. Tampering with the seat belt system
may result in serious personal injury. ●
Work on and around the front air bag system
should be done by an INFINITI retailer. Instal-
lation of electrical equipment should also be
done by an INFINITI retailer. The Supplemen-
tal Restraint System (SRS) wiring har-
nesses* should not be modified or discon-
nected. Unauthorized electrical test
equipment and probing devices should not
be used on the air bag system.
● A cracked windshield should be replaced im-
mediately by a qualified repair facility. A
cracked windshield could affect the function
of the supplemental air bag system.
*1.The SRS wiring harness connectors are yellow and orange for easy identifica-
tion.
When selling your vehicle, we request that you
inform the buyer about the front air bag system
and guide the buyer to the appropriate sections
in this Owner’s Manual.
FRONT SEAT-MOUNTED SIDE-IMPACT
SUPPLEMENTAL AIR BAG AND
ROOF-MOUNTED CURTAIN SIDE-
IMPACT AND ROLLOVER
SUPPLEMENTAL AIR BAG SYSTEMS
The side air bags are located in the outside of
the seatback of the front seats. The curtain and
rollover air bags are located in the side roof
rails. These systems are designed to meet
voluntary guidelines to help reduce the risk of
injury to out-of-position occupants. However, all
of the information, cautions and warnings in this
manual still apply and must be followed. The
side air bags and curtain and rollover air bags
are designed to inflate in higher severity side
SSS1092
1-60Safety — Seats, seat belts and supplemental restraint system