2011 HONDA ODYSSEY open hood

The alarm will also be activated if a
passenger inside the locked vehicle
turns the ignition switch on.
The security system will not set if
the hood, tailgate, or any door is not
f ully closed. Bef ore you leave the
vehicle, make sure the doors,
tailgate, and hood are securely
closed.To see if the system is set
af ter you exit the vehicle, press the
LOCK button on the remote
transmitter within 5 seconds. If the
system is set, the horn will beep
once.
Do not attempt to alter this system
or add other devices to it.
The security system helps to protect
your vehicle and valuables f rom thef t.
The horn sounds and a combination
of headlights, parking lights, side
marker lights, and taillights f lash if
someone attempts to break into your
vehicleorremovetheradio.This
alarm continues f or 2 minutes, then
the system resets. To reset an
activated system before the 2
minutes have elapsed, unlock the
driver’s door with the key or the
remote transmitter.
The security system automatically
sets 15 seconds after you lock the
doors, hood, and the tailgate. For the
system to activate, you must lock the
doorsandthetailgatefromthe
outside with the key, driver’s lock
tab, door lock master switch, or
remote transmitter. The security
system indicator on the instrument
panel starts blinking immediately to
show you the system is setting itself .
Once the security system is set,
opening any door, the tailgate, or the
hood without using the key or the
remote transmitter, will cause it to
alarm. It also alarms if the audio unit
is removed f rom the dashboard or
the wiring is cut.
On all models except LX
Security System
Features
479
NOTE:
SECURITY SYSTEM INDICATOR
10/07/17 10:38:38 31TK8600_484
2011 Odyssey

Bef ore you begin driving your
vehicle, you should know what
gasoline to use and how to check the
levels of important f luids. You also
need to know how to properly store
luggage or packages. The
inf ormation in this section will help
you. If you plan to add any
accessories to your vehicle, please
read the information in this section
first..............................
Break-in Period .540
.................
Fuel Recommendation . 540
.........
Service Station Procedures . 541
....................................
Ref ueling .541
Opening and Closing the .......................................
Hood .544
...................................
Oil Check .545
.............
Engine Coolant Check . 545
...............................
Fuel Economy .546
...
Accessories and Modif ications . 549
.............................
Carrying Cargo .551
Bef ore Driving
Bef ore Driving
539
10/07/17 10:46:56 31TK8600_544
2011 Odyssey

Holding the grip, pull the support
rod out of its clip. Insert the end
into the designated hole in the
hood.
To close the hood, lif t it up slightly to
remove the support rod f rom the
hole. Put the support rod back into
its holding clip. Lower the hood to
about a f oot (30 cm) above the
f ender, then let it drop. Make sure it
is securely latched.
Put your f ingers under the f ront
edge of the hood near the center.
Slide your hand to the lef t until
you f eel the hood latch handle.
Slide this handle to the right to
release the hood. Lif t up the hood.
If the hood latch handle moves stif f ly,
or you can open the hood without
lif ting the handle, the mechanism
should be cleaned and lubricated.
Park the vehicle, and set the
parking brake. Pull the hood
release handle located under the
lower lef t corner of the dashboard.
The hood will pop up slightly.
1.
3.
2.
Service Station ProceduresOpening and Closing the Hood544
SUPPORT ROD
LATCH CLIP
GRIP
Pull
HOOD RELEASE HANDLE
10/07/17 10:47:36 31TK8600_549
2011 Odyssey

Always change the oil and f ilter
according to the maintenance
messages shown on the odometer/
trip meter display or on the multi-
inf ormation display. The oil and f ilter
collect contaminants that can dam-
age your engine if they are not
removed regularly.
Changing the oil and f ilter requires
special tools and access f rom
underneath the vehicle. The vehicle
should be raised on a service station-
type hydraulic lif t f or this service.
Unless you have the knowledge and
proper equipment, you should have
this maintenance done by a skilled
technician.Run the engine until it reaches
normal operating temperature,
then shut it off.
Open the hood, and remove the
engine oil f ill cap. Remove the oil
drain bolt and washer f rom the
bottom of the engine. Drain the oil
into an appropriate container.Remove the oil f ilter, and let the
remaining oil drain. A special
wrench (available from your
dealer) is required.
Make sure the oil f ilter gasket is
not stuck to the contacting surface
of the engine. If it is, remove it
bef ore installing a new oil f ilter.
1.
2.
3.Changing the Engine Oil and Filter616
DRAIN BOLT
OIL FILTER
WASHER
10/07/17 10:56:37 31TK8600_621
2011 Odyssey

Open the hood.
To change a bulb on the driver’s
side, remove the upper part of the
air intake duct.
Use a f lat-tip screwdriver to
remove the holding clip, then
remove the upper part.To change a bulb on the
passenger’s side, use a f lat-tip
screwdriver to remove the holding
clip f rom the engine coolant
reserve tank, and then remove the
engine coolant reserve tank out of
its stay.
Remove the power steering
reservoir f rom the stay bracket to
get enough working space.
1.
2.
LightsHigh Beam Headlights626
HOLDING CLIPS
STAY
COOLANT RESERVE TANK
HOLDING CLIP POWER STEERING RESERVOIR
STAY BRACKET
10/07/17 10:57:56 31TK8600_631
2011 Odyssey

Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector onto
the new bulb.
Turn on the headlights to test the
new bulb.
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it
about one-quarter turn
counterclockwise. Reinstall the air intake duct
securely.
Reinstall the engine coolant
reserve tank and power steering
reservoir. Open the hood.
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it
about one-quarter turn
counterclockwise.
4. 5.
6.
3. 7.
8.
2.
3. 1.
CONT INUED
Driver’s sidePassenger’s side
Lights
L ow Beam Headlight s
Maint enance
627
TAB
CONNECTOR BULB
BULBTAB
CONNECTOR
10/07/17 10:58:08 31TK8600_632
2011 Odyssey

Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector onto
the new bulb.
Turn on the headlights to test the
new bulb.Open the hood.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.Turn on the lights to make sure
the new bulb is working. Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place. Push the new bulb straight into
the socket until it bottoms.
1.
4.
5.
6.
2.
3. 4.
5.
6.
Lights
Replacing the Front Side Marker/
Parking/Turn Signal Light Bulb
628
BULB
SOCKET
10/07/17 10:58:18 31TK8600_633
2011 Odyssey

Check the condition of the wiper
blades at least every 6 months.
Replace them if you f ind signs of
cracking in the rubber, and areas
that are getting hard or if they leave
streaks and unwiped areas when
used.Raise the wiper arm of f the
windshield. Raise the driver’s side
first, then the passenger’s side.Disconnect the blade assembly
from the wiper arm:
To replace a f ront wiper blade:
Press and hold the lock tab.
Slide the blade assembly toward
the lock tab until it releases f rom
the wiper arm.
When replacing a wiper blade,
make sure not to drop the wiper
blade or wiper arm down on the
windshield.
2.
1.Wiper Blades638
WIPER ARMS LOCK TAB
Do not open the hood when the wiper
arms are raised, or you will damage the
hood and the arms.
10/07/17 10:59:44 31TK8600_643
2011 Odyssey