2011 HONDA CR-Z warning
[x] Cancel search: warningPage 274 of 333
273
Maintenance
Checking and Maintaining Tires DOT Tire Quality Grading (U.S. Vehicles)
Traction
■
The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
Temperature
■
The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.
Traction
Warning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
Temperature
Warning: The temperature grade for this tire is established for a tire that is properly inlated and not overloaded. Excessive speed, underinlation, or excessive loading, either separately or in
combination, can cause heat buildup and possible tire failure.
Main MenuTable of Contents
Page 276 of 333
275
Maintenance
Checking and Maintaining Tires Tire and Wheel Replacement
Tire and Wheel Replacement
Tire and Wheel Replacement
WARNING
Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed. Always use the size and type of tires recommended in this owner’s manual.
Replace your tires with radials of the same size, load range, speed rating, and maximum cold tire pressure rating (as shown on the tire’s sidewall). Using tires of a different size or construction can cause the ABS and VSA®
(vehicle stability assist)
system to work incorrectly. It is best to replace all four tires at the same time. If that isn’t possible, replace the front or rear tires in pairs.
U.S. models only
If you replace a wheel, only use TPMS specified wheels approved for your vehicle.
Main MenuTable of Contents
Page 278 of 333
277
Maintenance
Checking and Maintaining Tires Winter Tires
Winter Tires If driving on snowy or frozen roads, mount all season marked “M + S” tires, snow tires, or tire chains; reduce speed; and maintain sufficient distance between vehicles when driving. Be particularly careful when operating the steering wheel or brakes to prevent skidding. Use tire chains, snow tires, or all season tires when necessary or according to the law. When mounting, refer to the following points. For winter tires:Select the size and load ranges that are the same as the original tires.
•
Mount the tires to all four wheels.
•
For tire chains: Install them on the front tires only. Because your vehicle has limited tire
•
clearance, Honda strongly recommends using the chains listed below:
Cable-type: SCC Radial Chain SC1030
Follow the chain manufacturer’s instruction when installing. Mount them as
•
tightly as you can. Check that the chains do not touch the brake lines or suspension.
•
Drive slowly.
•
Winter Tires
NOTICE Traction devices that are the wrong size or improperly installed can damage your vehicle's brake lines, suspension, body, and wheels. Stop driving if they are hitting any part of the vehicle. When tire chains are mounted, follow the chain manufacturer's instructions regarding vehicle operational limits.
WARNING
Using the wrong chains, or not properly installing chains, can damage the brake lines and cause a crash in which you can be seriously injured or killed. Follow all instructions in this owner’s manual regarding the selection and use of tire chains.
Main MenuTable of Contents
Page 279 of 333
278
Maintenance
12 Volt Battery
Checking the 12 Volt Battery
Check the battery condition monthly. Look at the test indicator window and check the terminals for corrosion.
If your vehicle’s battery is disconnected or goes dead: The audio system is disabled.
•
Entering the Security Code P.140
The clock resets.
•
Setting the Clock P.98
The navigation system is disabled. A PIN code will be required.
•
Refer to the navigation system manual.
Charging the 12 Volt Battery Disconnect both battery cables to prevent damaging your vehicle’s electrical system. Always disconnect the negative (–) cable first, and reconnect it last.
Test Indicator Window 12 Volt Battery
WARNING: Battery posts, terminals, and
related accessories contain lead and lead compounds.Wash your hands after handling. The test indicator's color information is on the battery. When you ind corrosion, clean the battery terminals by applying a baking powder and water solution. Rinse the terminals with water. Cloth/towel dry the battery. Coat the terminals with grease to help prevent future corrosion. If the 12 volt battery is disconnected or goes dead, the IMA battery level gauge reading may show less than the actual level the next time you turn the ignition switch to ON
. It will show the correct
level after you drive for about 30 minutes.
WARNING
The battery gives off explosive hydrogen gas during normal operation. A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you. Wear protective clothing and a face shield, or have a skilled technician do any battery maintenance.
Main MenuTable of Contents
Page 288 of 333
287
Handling the Unexpected
If a Tire Goes Flat
Changing a Flat Tire
Changing a Flat Tire
Periodically check the tire pressure of the compact spare. It should be set to the speciied pressure.Speciied Pressure: 60 psi (420 kPa, 4.2 kgf/cm 2
)
When driving with the compact spare tire, keep the vehicle speed under 50 mph (80 km/h).Replace with a full size tire as soon as possible. The compact spare tire and wheel in your vehicle are speciically for this model.Do not use them with another vehicle.Do not use another type of compact spare tire or wheel with your vehicle. Do not mount tire chains on a compact spare tire. If a chain-mounted front tire goes lat, remove one of the full-size rear tires and replace it with the compact spare tire. Remove the lat front tire and replace it will the full size tire that was removed from the rear. Mount the tire chains on the front tire.
If a tire goes flat while driving, grasp the steering wheel firmly, and brake gradually to reduce speed. Then, stop in a safe place. Replace the flat tire with the compact spare tire. Go to a dealer as soon as possible to have the full size tire repaired or replaced.
Park the vehicle on firm, level, and non-slippery ground.
1.
Put the shift lever in
2.
P (CVT).
Put the shift lever in
R (manual transmission).
Set the parking brake.
3.
Turn on the hazard warning lights and turn the ignition switch to LOCK
4.
0.
Main MenuTable of Contents
Page 291 of 333
290
Handling the Unexpected
If a Tire Goes Flat Changing a Flat Tire
How to Set Up the Jack
■
1. Place the jack under the jacking point closest to the tire to be changed.
2. Turn the end bracket (as shown in the image) clockwise until the top of the jack contacts the jacking point.
Make sure that the jacking point tab is
resting in the jack notch.
3. Raise the vehicle, using the extension bar and the jack handle, until the tire is off the ground.
Changing a Flat Tire
Do not use the jack with people or luggage in the vehicle. Use the jack provided in your vehicle. Other jacks may not support the weight ("load") or their shape may not match the jacking point.The following instructions must be followed to use the jack safely. Do not use while the engine is running.
•
Use only where the ground is irm and level.
•
Use only at the jacking points.
•
Do not get in the vehicle while using the jack.
•
Do not put anything on top of or underneath
•
the jack.
WARNING
The vehicle can easily roll off the jack, seriously injuring anyone underneath. Follow the directions for changing a tire exactly, and never get under the vehicle when it is supported only by the jack.
Wheel Nut
Wrench as Jack Handle
Extension Bar
Main MenuTable of Contents
Page 293 of 333
292
Handling the Unexpected
If a Tire Goes Flat Changing a Flat Tire
Storing the Flat Tire
■
1. Remove the center cap and place the flat tire face down in the spare tire well.Remove the spacer cone from the wing
2.
bolt, flip it over, and insert it back on the bolt. Secure the flat tire with the wing bolt. Securely put the jack and wheel nut
3.
wrench back in the tool case in the cargo area.
TPMS and the Spare Tire
■
U.S. models only
If you replace a flat tire with the spare tire, the low tire pressure/TPMS indicator comes on while you are driving. After driving for a few miles (kilometers), the indicator will start blinking for a short time and then stay on. “CHECK TPMS SYSTEM” appears on the multi-information display, but this is normal. If you replace the tire with a specified regular tire, the warning message on the multi-information display and the low tire pressure/TPMS indicator will go off after a few miles (kilometers).
Storing the Flat Tire
WARNING
Loose items can fly around the interior in a crash and can seriously injure the occupants. Store the wheel, jack, and tools securely before driving.
Spacer Cone
Wing Bolt
For compact spare tire
For normal tire
TPMS and the Spare Tire
The system cannot monitor the pressure of the
spare tire. Manually check the spare tire pressure to
be sure that it is correct. Use TPMS speciic wheels. Each is equipped with a tire pressure sensor mounted inside the tire behind the valve stem.
Main MenuTable of Contents
Page 295 of 333
294
Handling the Unexpected
Jump Starting
Jump Starting Procedure
■
Turn off the power to electric devices, such as audio and lights. Turn off the engine, then open the hood.
1. Connect the first jumper cable to your vehicle’s battery
terminal.
Connect the other end of the first jumper
2.
cable to the assisting vehicle’s
terminal.
Use a 12 volt booster battery only.
Connect the second jumper cable to the
3.
assisting vehicle’s
terminal.
4. Connect the other end of the second jumper cable to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine. If your vehicle is connected to another
5.
vehicle, start the assisting vehicle’s engine and increase its rpm slightly. Attempt to start your vehicle’s engine. If
6.
it turns over slowly, check that the jumper cables have good metal-to-metal contact.
Jump Starting
Securely attach the jumper cables clips so that they do not come off when the engine vibrates. Also be careful not to tangle the jumper cables or allow the cable ends to touch each other while attaching or detaching the jumper cables. Battery performance degrades in cold conditions and may prevent the engine from starting.
WARNING
A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby. Keep all sparks, open flames, and smoking materials away from the battery.
Assisting
Vehicle’s Battery
Main MenuTable of Contents