Page 294 of 333
293
Handling the Unexpected
Engine Does Not Start
Checking the Engine If the engine does not start, turn the ignition switch to START
and check the
starter. Checking the Engine
If you must start the vehicle immediately, use an assisting vehicle to jump start it.
Jump Starting P.294
Starter Condition Check List
Starter will not start at all. Starter turns over very slowly.The 12 volt battery may be dead. Check each of the items on the right and respond accordingly. Check brightness of the interior light.Turn on interior lights and check brightness.
If the interior lights are dim or do not come on at all
•
12 Volt Battery Inspection and Maintenance P. 2 7 8
If the interior lights come on normally
•
Fuse Inspection and Replacement P. 3 0 4
The starter turns over normally but...There may be a problem with the fuse. Check each of the items on the right and respond accordingly. Review the engine start procedure.Follow its instructions, and try to start the engine again.
Staring the Engine
P.1 9 7
Check the immobilizer system indicator. When the immobilizer system indicator is blinking, the engine cannot be started.
Immobilizer System P.1 0 5
Check the fuel level. There should be enough fuel in the tank.
Fuel Gauge P.1 4
Check the fuse. Check all fuses, or have the vehicle checked by a dealer.
Inspecting and Changing Fuses P. 3 0 4
If the problem continues:
Emergency Towing P. 3 0 8
Main MenuTable of Contents
Page 295 of 333
294
Handling the Unexpected
Jump Starting
Jump Starting Procedure
■
Turn off the power to electric devices, such as audio and lights. Turn off the engine, then open the hood.
1. Connect the first jumper cable to your vehicle’s battery
terminal.
Connect the other end of the first jumper
2.
cable to the assisting vehicle’s
terminal.
Use a 12 volt booster battery only.
Connect the second jumper cable to the
3.
assisting vehicle’s
terminal.
4. Connect the other end of the second jumper cable to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine. If your vehicle is connected to another
5.
vehicle, start the assisting vehicle’s engine and increase its rpm slightly. Attempt to start your vehicle’s engine. If
6.
it turns over slowly, check that the jumper cables have good metal-to-metal contact.
Jump Starting
Securely attach the jumper cables clips so that they do not come off when the engine vibrates. Also be careful not to tangle the jumper cables or allow the cable ends to touch each other while attaching or detaching the jumper cables. Battery performance degrades in cold conditions and may prevent the engine from starting.
WARNING
A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby. Keep all sparks, open flames, and smoking materials away from the battery.
Assisting
Vehicle’s Battery
Main MenuTable of Contents
Page 296 of 333
295
Handling the Unexpected
Jump Starting
What to Do After the Engine Starts
■
Once your vehicle’s engine has started, remove the jumper cables in the following order.
Disconnect the jumper cable from your vehicle’s grounding strap.
1.
Disconnect the other end of the jumper cable from the assisting vehicle’s battery
2.
terminal.
Disconnect the jumper cable from your vehicle’s battery
3.
terminal.
Disconnect the other end of the jumper cable from the assisting vehicle’s battery
4.
terminal.
Have your vehicle inspected by a nearby service station or a dealer.
Main MenuTable of Contents
Page 301 of 333
300
Handling the Unexpected
Indicator, Coming On/Blinking If the Charging System Indicator Comes On
If the Charging System Indicator Comes On ■Reasons for the Indicator to Come On
Comes on when the 12 volt battery is not being charged.
What to Do When the Indicator Comes On
■
Turn off the climate control system, rear defogger, and other electrical systems, and immediately contact a dealer for repairs.
If the Charging System Indicator Comes On
If you need to stop temporarily, do not turn off the
engine. Restarting the engine may rapidly discharge the 12 volt battery.
Manual transmission model This indicator may also come on when the auto idle stop function is activated for a while. Restart the engine.
Auto Idle Stop (Manual Transmission) P. 227
Automatic transmission (CVT) model This indicator may also come on when the IMA battery charge drops below a desired level.The engine starts to recharge the battery.
Auto Idle Stop (CVT) P. 224
The indicator goes off when the battery is being charged normally. This indicator may blink after starting when the outside temperature is below -20°F (-30°C). It will stop blinking after the IMA battery warms up.
Main MenuTable of Contents
Page 305 of 333
304
Handling the Unexpected
Fuses
Fuse Locations
If any electrical devices are not working, turn the ignition switch to LOCK 0 and
check to see if any applicable fuse is blown.
Engine Compartment Fuse Box
■
Located near the + terminal on the 12 volt battery.
1. Pull on the tab to release the front of the cover.Pull up the cover by pushing the two tabs
2.
as shown. Replacement of engine compartment fuses should be done by a dealer.
Circuit Protected and Amps for Each
■
Fuse
Circuit Protected Amps
1 Battery 100 A
2 EPS 70 A
3 Horn, Stop, Hazard 20 A
Fuse Locations
Fuse locations are shown on the fuse box cover.
Locate the fuse in question by the fuse number and box cover number.
Fuse Box
Main MenuTable of Contents
Page 313 of 333
312
Information
Speciications
Vehicle Specifications
■
Model Honda CR-Z No. of Passengers:
Front RearTotal 2–2
Weights: Gross Vehicle Weight Rating U.S.: 3,164 lbs (1,435 kg)Canada: 1,435 kg
Gross Axle Weight Rating (Front) U.S.: 1,797 lbs (815 kg)Canada: 815 kg
Gross Axle Weight Rating (Rear) U.S.: 1,378 lbs (625 kg)Canada: 625 kg
Air Conditioning: Refrigerant TypeCharge QuantityLubricant Type HFC-134a (R-134a)15.8 – 17.6 oz (450 – 500 g)SP-10
Engine Specifications
■
Displacement 91 cu-in (1,497 cm 3
)
Spark Plugs NGK DIFR6A13G
DENSO DK20PR-D13
Fuel
■
Fuel: Type Unleaded gasoline, Pump octane number of 87 or higher
Fuel Tank Capacity 10.6 US gal (40 ℓ)
12 Volt Battery
■
Capacity/Type 32AH(5)/40AH(20) 34AH(5)/40AH(20)
Washer Fluid
■
Tank Capacity U.S.: 2.6 US qt (2.5 ℓ) Canada: 4.8 US qt (4.5 ℓ)
Light Bulbs
■
Headlights (Low Beam) 35W (D4S)*
1
55W (H11)* 2
Headlights (High Beam) 60W (HB3)
Fog Lights* 55W (H11)Front Turn Signal/Parking/ Side Marker Lights 28W/8W
Side Turn Signal Lights(on Door Mirrors) LED
Brake/Taillights LED
Rear Turn Signal Lights 21W (Amber)
Back-Up Lights 16W
Rear Side Marker Lights 3CP
High-Mount Brake Light LED
License Plate Lights 5W
Cargo Area Light 5WInterior Lights
Front
Rear 8W3.4W
Vanity Mirror Lights* 2W
Glove Box Light 1.4W
Courtesy Lights 2CP (3.8W)
*1: Vehicle with discharge headlights
*2: Vehicle with halogen bulb low beam headlights
* Not available on all models
Main MenuTable of Contents
Page 318 of 333
317
Information
Emissions Testing
Testing of Readiness Codes
Testing of Readiness Codes
The readiness codes are erased when the 12 volt battery is disconnected, and set again only after several days of driving under a variety of conditions. If a testing facility determines that the readiness codes are not set, you may be requested to return at a later date to complete the test.
If the testing facility determines the readiness co des
are still not set, see a dealer.
Your vehicle uses “readiness codes,” as part of it’s onboard self diagnostic system. Some States refer to these codes during testing to see if your vehicle’s emissions components are working properly. The codes may not be read if you go through the testing just after the battery has gone dead or been disconnected. To check if they are set, turn the ignition switch to ON
II, without starting the
engine. The malfunction indicator lamp will come on for several seconds. If it then goes off, the readiness codes are set. If it blinks five times, the readiness codes are not set. If you are required to have your vehicle tested before the readiness codes are ready, prepare the vehicle for retesting by doing the following:
Fill the gas tank to approximately 3/4 full.
1.
Park the vehicle and leave the engine off for 6 hours or more.
2.
Make sure the ambient temperature is between 40 °F and 95 °F (4 °C and 35
3.
°C).Start the engine without touching the accelerator pedal, and let it idle for 20
4.
seconds.Keep the vehicle in
5.
P (automatic transmission) or N (manual transmission).
Increase the engine speed to 2,000 rpm, and hold it there for about 3 minutes. Let the engine idle with your foot off the accelerator for 20 seconds.
6.
continued
Main MenuTable of Contents
Page 323 of 333
322
Information
Warranty Coverages
Replacement Battery Limited Warranty – provides prorated coverage
for a replacement battery purchased from your dealer. Replacement Muffler Lifetime Limited Warranty – provides coverage
for as long as the purchaser of the muffler owns the vehicle.Restrictions and exclusions apply to all these warranties. Please read the 2011 Honda warranty information booklet that came with your vehicle for precise information on warranty coverages. Your vehicle’s original tires are covered by their manufacturer. Tire warranty information is in a separate booklet.
Canadian Owners
Please refer to the 2011 warranty manual that came with your vehicle.
Main MenuTable of Contents
