2011 FORD SUPER DUTY steering

Operation in standing water
Ingestion of water into the diesel engine can result in immediate and
severe damage to the engine. If driving through water, slow down to
avoid splashing water into the intake. If the engine stalls, and ingestion
of water into the engine is suspected, do not try to restart the engine.
Consult your dealer for service immediately.
Engine block heater (if equipped)
Refer to theDrivingchapter in theOwner’s Guide.
Rapid heat supplemental heating system (if equipped)
The optional rapid heat feature is an electrically powered device that is
designed to provide supplemental heat during engine warm up. For
maximum effectiveness mid to low blower speed is recommended during
initial warm up. When operating in automatic mode (when equipped) the
climate control unit will determine the appropriate blower speed for
existing conditions.
Note:Additional aftermarket electrical loads operated during engine
warm up may impact the performance of the rapid heat supplemental
heater.
DUAL FUEL TANK SELECTOR CONTROL (IF EQUIPPED)
If your vehicle is equipped with dual
fuel tanks, you will have a selector
control, located to the right of the
steering wheel, which allows you to
draw fuel from either tank. Your fuel
gauge will display the amount of
fuel in the currently selected tank.
TRAILER TOWING
Refer to yourOwner’s Guidefor full details on towing a trailer.
Driving
14
2011 Econoline(eco)
Supplement, 1st Printing
USA(fus)

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT
F-Super Duty
1. Engine oil dipstick
2. Automatic transmission dipstick
3. Brake fluid reservoir
4. Power distribution box
5. Batteries
6. Engine cooling system coolant reservoir (primary high-temperature
cooling system)
7. Power steering fluid reservoir
8. Engine oil fill
9. Engine-mounted fuel filter assembly
10. Secondary cooling system coolant reservoir
11. Air filter assembly
12. Air filter restriction gauge
13. Windshield washer fluid reservoir
1135234
57691012118
Maintenance and Specifications
20
2011 Econoline(eco)
Supplement, 1st Printing
USA(fus)

Coolant change interval
❑6 years or 105,000 miles (168,000 km) - change coolant (whichever comes first) or as indicated from the coolant tests
for concentration (freeze-point) or additive strength (corrosion inhibitor).
❑After initial change - change coolant every 3 years or 45,000 miles (72,000 km) or as indicated from the coolant tests
for concentration (freeze-point) or additive strength (corrosion inhibitor).
❑Use coolant specified in theOwner’s Guideunder theMaintenance and Specificationschapter
❑For special operating conditions, seeSpecial Operating Conditionsat the end of this section
Check every month
❑Check function of all interior and exterior lights❑Check tires for wear and adjust air pressure (including spare tire)
❑Check that holes in the tail-pipe of the exhaust system are clear of debris-the holes/slots are functional
❑Check engine oil level
❑Check windshield washer fluid level
❑Check and drain fuel filter/water separator
❑Check air filter restriction gauge
Check every six months
❑Check lap/shoulder belts and seat latches for wear and function❑Check that externally-mounted spare tire is tight (seeOwner’s Guide)
❑Check power steering fluid level
❑Check washer spray, wiper operation and clean all wiper blades (replace as necessary)
❑Check parking brake for proper operation
❑Check and lubricate all hinges, latches and outside locks
❑Check and lubricate door rubber weatherstrips
❑Check and clean body and door drain holes
❑Check safety warning lamps (brake, ABS, air bag, safety belt) for operation
❑Check engine and secondary cooling system concentration (freeze-point protection), additive strength (corrosion inhibitor),
coolant level and hoses
❑Check battery connections and clean if necessary
Retightening lug nuts
❑On vehicles equipped with single rear wheels, retighten the lug nuts to the specified torque at 500 miles (800 km) after
any wheel disturbance (tire rotation, changing a flat tire, wheel removal, etc.).
❑On vehicles equipped with dual rear wheels, retighten the wheel lug nuts to the specified torque at 100 miles (160 km),
and again at 500 miles (800 km) of new vehicle operation and after any wheel disturbance (tire rotation, changing a flat
tire, wheel removal, etc.).
❑Refer toWheel Lug Nut Torque Specificationin yourOwner’s Guidefor the proper lug nut torque specification.
Scheduled Maintenance Guide
66
2011 Econoline(eco)
Supplement, 1st Printing
USA(fus)

Multi-point inspection
In order to keep your vehicle running right, it is important that you have
the systems on your vehicle checked regularly. This can help identify any
potential issue before there are any problems. Ford Motor Company
suggests the following multi-point inspection to be performed at every
scheduled maintenance interval as the way to ensure your vehicle keeps
running right.
NORMAL SCHEDULED MAINTENANCE AND LOG
For your convenience, your vehicle is equipped with a message center
which calculates the proper oil change service interval. You should
perform the engine oil change as indicated by the instrument cluster
message center. The message center will display ENGINE OIL CHANGE
SOON or OIL CHANGE REQUIRED to indicate when an oil change is
needed. The engine oil change service needs to be completed within two
weeks or 500 miles (800 km) after the OIL CHANGE REQUIRED
message is displayed. Your oil change service interval can be up to one
year or 10,000 miles (16,000 km). Reset your Intelligent Oil Life
Monitor™ after each engine oil and filter change; refer to the
Instrument Clusterchapter of the owner guide.
If your message center is prematurely reset or becomes inoperative, you
should perform the oil change interval at six months, 5,000 miles
(8,000 km) or 200 hours from your last oil change.
Multi-point inspection - recommended at every visit
❑Check and top-up fluid levels: brake, engine coolant reservoir, secondary low-temperature cooling system reservoir, automatic
transmission, power steering, window washer.
❑Inspect tires for wear and check air pressure, including spare.
❑Check exhaust system for leaks, damage, loose parts and foreign materials.
❑Check that holes in the tail-pipe of the exhaust system are clear of debris; the holes/slots are functional
❑Check battery performance.
❑Check operation of horn, exterior lamps, turn signals and hazard warning lights.
❑Check radiators, coolers and heater and air conditioning hoses.
❑Inspect windshield washer spray and wiper operation.
❑Check windshield for cracks, chips and pitting.
❑Inspect for oil and fluid leaks.
❑Inspect air filter.
❑Check shocks and struts and other suspension components for leaks and damage.
Scheduled Maintenance Guide
67
2011 Econoline(eco)
Supplement, 1st Printing
USA(fus)

Oil Change Service Interval* 1 2 345678910
Change engine oil and filter• •••••••••
Refill diesel exhaust fluid tank• •••••••••
Rotate tires, inspect tire wear and measure tread
depth. Vehicles equipped with dual rear wheels
should only rotate if unusual wear is observed.• •••••••••
Inspect air filter restriction gauge, replace filter as
necessary• •••••••••
Inspect wheels and related components for abnormal
noise, wear, looseness or drag• •••••••••
Inspect and lubricate steering linkage, ball joints,
suspension, tie rod ends, driveshaft, front axle
U-joints (4WD vehicles)• •••••••••
Perform multi-point inspection (recommended)• •••••••••
Inspect automatic transmission fluid level•••••
Inspect brake pads, shoes, rotors, drums, brake
linings, hoses and parking brake•••••
Inspect exhaust system and heat shields•••••
*Oil change service intervals should be completed as indicated by the instrument cluster message center
Reset your Intelligent Oil Life Monitor™ after each engine oil and filter change; refer to theInstrument Clusterchapter
of theOwner’s Guide
Scheduled Maintenance Guide
69
2011 Econoline(eco)
Supplement, 1st Printing
USA(fus)

Oil Change Service Interval* 11 12 13 14 15 16 17 18 19 20
Change engine oil and filter• •••••••••
Refill diesel exhaust fluid tank• •••••••••
Rotate tires, inspect tire wear and measure tread
depth. Vehicles equipped with dual rear wheels
should only rotate if unusual wear is observed.• •••••••••
Inspect air filter restriction gauge, replace filter as
necessary• •••••••••
Inspect wheels and related components for abnormal
noise, wear, looseness or drag• •••••••••
Inspect and lubricate steering linkage, ball joints,
suspension, tie rod ends, driveshaft, front axle
U-joints (4WD vehicles)• •••••••••
Perform multi-point inspection (recommended)• •••••••••
Inspect automatic transmission fluid level•••••
Inspect brake pads, shoes, rotors, drums, brake
linings, hoses and parking brake•••••
Inspect exhaust system and heat shields•••••
*Oil change service intervals should be completed as indicated by the instrument cluster message center
Reset your Intelligent Oil Life Monitor™ after each engine oil and filter change; refer to theInstrument Clusterchapter
of theOwner’s Guide
Scheduled Maintenance Guide
70
2011 Econoline(eco)
Supplement, 1st Printing
USA(fus)

Operating in dusty conditions such as unpaved or dusty roads
Every 7,500 miles (12,000 km)– Rotate tires, inspect tires for wear and measure tread
depth and inspect wheel ends for endplay and noise.
Vehicles equipped with dual rear wheels should only rotate
if unusual wear is observed.
– Inspect and lubricate steering and suspension ball joints
and tie rods (if equipped with grease fittings)
– Inspect air filter restriction gauge (replace air filter as
required or when air filter restriction gauge indicates)
– Inspect brake system pads and rotors
Every 7,500 miles (12,000 km),
300 hours of engine operation or
6 months– Change engine oil and replace filter
– Inspect and lubricate U-joints
Every 15,000 miles (24,000 km),
6 months, 600 hours of engine
operation, or as indicated by the
message center or instrument
cluster (whichever occurs first)– Change engine- and frame-mounted fuel filters
Every 30,000 miles (48,000 km)– Replace wheel bearing grease and grease seals on 4x2
wheel bearings (if non-sealed bearings are used)
Reset your Intelligent Oil Life Monitor™ after each engine oil and filter
change; refer to theInstrument Clusterchapter of theOwner’s Guide.
Scheduled Maintenance Guide
80
2011 Econoline(eco)
Supplement, 1st Printing
USA(fus)

Off-road operation
Every 7,500 miles (12,000 km)– Inspect air filter restriction gauge (replace air filter as
required or when air filter restriction gauge indicates)
– Rotate tires, inspect tires for wear and measure tread
depth and inspect wheel ends for endplay and noise.
Vehicles equipped with dual rear wheels should only rotate
if unusual wear is observed.
– Inspect brake system pads and rotors
Every 7,500 miles (12,000 km) or
300 hours of engine operation– Change engine oil and replace filter
– Inspect and lubricate U-joints
Every 15,000 miles (24,000 km),
6 months, 600 hours of engine
operation, or as indicated by the
message center or instrument
cluster (whichever occurs first)– Change engine- and frame-mounted fuel filters
Every 30,000 miles (48,000 km)– Replace wheel bearing grease and grease seals on 4x2
wheel bearings (if non-sealed bearings are used)
Every 50,000 miles (80,000 km)– Change rear axle lubricant (if equipped with a DANA
rear axle, some F-350s, all 450–550)
– Inspect front axle lubricant (4x4 only)
– Change transfer case fluid (4x4 only)
As required– Inspect and lubricate steering and suspension ball joints
and tie rod ends (if equipped with grease fittings)
– Inspect functional holes in each leg of the twin tip and
the holes under the shield just inboard of the right rear
tire to make sure they are kept clean/clear of debris or
foreign materials (clean/remove debris as required). Refer
to the
Cleaningchapter for more information.
Reset your Intelligent Oil Life Monitor™ after each engine oil and filter
change; refer to theInstrument Clusterchapter of theOwner’s Guide.
Scheduled Maintenance Guide
81
2011 Econoline(eco)
Supplement, 1st Printing
USA(fus)