2011 FORD C MAX engine

Downloaded from www.Manualslib.com manuals search engine Grand C-MAX
Second row centre seat belt anchor
point Second row centre seat belt
The retractor for the rear centre seat belt
is located in the roof.
To fasten the seat belt:
1. Pull the belt out steadily. It may lock if
you pull it sharply or if the vehicle is on
a slope.
2. Securely attach the spring hook to the anchor point.
3. Pull the tongue across the lap and insert it into the buckle to the right of
the centre seat.
Note: If in constant use, you can leave the
belt attached to the anchor point. When it
is not in use, or when you fold or move the
rear seats, you should release the spring
hook from the anchor point.
31
Occupant protectionE130029 E129522213

Downloaded from www.Manualslib.com manuals search engine Press the red button on the right buckle to
release the belt. Let it retract.
Unclip the spring hook to release the belt.
Let it retract completely and smoothly to
the retractor in the roof.
Stow the tongue securely flat against the
roof trim.
WARNING
Always replace the rubber cover
when stowing the belt assembly.
Third row seat belts
Note:
When not in use, place the seat belts
in the clips on the outboard trim. Make sure
that the seat belt tongue is positioned above
the clip. 32
Occupant protectionE129524 E135424 E135425

Downloaded from www.Manualslib.com manuals search engine SEAT BELT HEIGHT
ADJUSTMENT
Note:
Lifting the slider slightly while
pressing the locking button makes it easier
to release the locking mechanism.
To raise or lower, press the locking button
on the adjuster and move as necessary.
SEAT BELT REMINDER WARNING
The occupant protection system will
only provide optimum protection
when you use the seat belt properly.
The seat belt reminder warning
lamp illuminates and an audible
warning will sound if the driver's
or front seat passenger's seat belt has not
been fastened and the vehicle exceeds a
relatively low speed. It will also illuminate
if the driver's or front seat passenger's seat
belt is unfastened when the vehicle is
moving. The audible warning will go off
after a few minutes but the seat belt
reminder warning lamp will remain on until
the driver's or front seat passenger's seat
belt is fastened. Deactivating the seat belt
reminder
See your dealer.
Grand C-MAX only
Rear seat belt reminder
WARNING
If multiple belts are unfastened
within a few seconds of each other,
only one audible chime will sound.
Note:
Press the OK button on the steering
wheel control to confirm the message.
A visual reminder of the seat belt status
will be shown on the instrument display
once the engine is started, and once again
if any are unfastened when the vehicle is
moving.
Fastened seat belts are indicated by a tick
symbol.
If a belt is unfastened when the vehicle is
moving, the seat belt status screen will be
displayed and the relevant seats will be
highlighted by an exclamation mark. An
audible chime will also sound.
USING SEAT BELTS DURING
PREGNANCY 33
Occupant protectionE87511 E68587

Downloaded from www.Manualslib.com manuals search engine WARNING
Position the seat belt correctly for
your safety and that of your unborn
child. Do not use only the lap strap
or the shoulder strap. Position the lap strap comfortably across
your hips and low beneath your pregnant
abdomen. Position the shoulder strap
between your breasts, above and to the
side of your pregnant abdomen.
DISABLING THE PASSENGER
AIRBAG
WARNING
Make sure that the passenger airbag
is disabled when using a rearward
facing child restraint on the front
passenger seat. Fitting the passenger airbag
deactivation switch
WARNING
If you need to fit a child restraint on
a seat protected by an operational
airbag in front of it, have a passenger
airbag deactivation switch fitted. Ask your
dealer for further information. Note:
The key switch is located at the end
of the instrument panel on the side of the
glove compartment. The airbag deactivation
lamp is located between the sun visors. If the airbag warning lamp illuminates or
flashes when you are driving, this indicates
a malfunction. See Warning Lamps and
Indicators (page 79). Remove the child
restraint and have the system checked
immediately.
Disabling the passenger airbag
Disabled
A
Enabled
B
Turn the switch to position A.
When you switch the ignition on, check that
the passenger airbag deactivation warning
lamp illuminates.
34
Occupant protectionE71313 E130110 ABE71312

Downloaded from www.Manualslib.com manuals search engine Enabling the passenger airbag
WARNING
Make sure that the passenger airbag
is enabled when you are not using a
child restraint on the front passenger
seat. Turn the switch to position B.
35
Occupant protection

Downloaded from www.Manualslib.com manuals search engine GENERAL INFORMATION ON
RADIO FREQUENCIES
CAUTIONS
The radio frequency used by your
remote control can also be used by
other short distance radio
transmissions (e.g. amateur radios,
medical equipment, wireless headphones,
remote controls and alarm systems). If the
frequencies are jammed, you will not be
able to use your remote control. You can
lock and unlock the doors with the key. Check your vehicle is locked before
leaving it unattended. This will
safeguard against any potential
malicious frequency blocking. Note:
You could unlock the doors if you
press the buttons on the remote control
unintentionally.
The operating range between your remote
control and your vehicle varies depending
on the environment.
PROGRAMMING THE REMOTE
CONTROL
You can programme a maximum of eight
remote controls to use with your vehicle
(including any supplied with your vehicle).
Programming a new remote
control
1. Insert the key in the ignition.
2. Cycle the key from position 0 to II and
then back to 0 four times within six
seconds.
3. Leave the key in position 0 and press any button on the remote control
within 10 seconds. You will receive
confirmation via a chime or LED that
programming has been successful. Note:
Further remote controls may be
programmed at this stage.
4. Press any button on each additional remote control within 10 seconds of
each other.
Reprogramming the unlocking
function
Note: When you press the unlock button
either all the doors are unlocked or only the
driver ’s door is unlocked. Pressing the unlock
button again unlocks all the doors.
Press and hold the unlock and lock buttons
on the remote key simultaneously for at
least four seconds with the ignition off. The
direction indicators will flash twice to
confirm the change.
To return to the original unlocking function,
repeat the process.
CHANGING THE REMOTE
CONTROL BATTERY Make sure that you dispose of
old batteries in an
environmentally friendly way.
Seek advice from your local authority
regarding recycling.
Remote control with a folding key
blade 36
Keys and Remote ControlsE107998 E12880921

Downloaded from www.Manualslib.com manuals search engine 1. Insert a screwdriver in the position
shown and gently push the clip.
2. Press the clip down to release the battery cover. 3. Carefully remove the cover.
4.
Turn the remote control over to remove
the battery.
5. Install a new battery (3V CR 2032) with
the + facing upwards.
6. Replace the battery cover. Remote control without a folding
key blade
1.
Press and hold the pushbuttons on the
edges to release the cover. Carefully
remove the cover.
2. Remove the key blade. 3. Twist a flat bladed screwdriver in the
position shown to separate the two
halves of the remote control.
37
Keys and Remote ControlsE128810 E128811 121E87964 E1053623

Downloaded from www.Manualslib.com manuals search engine 4. Carefully insert the screwdriver in the
position shown to open the remote
control. CAUTION
Do not touch the battery contacts or
the printed circuit board with the
screwdriver.
5.
Carefully prise out the battery with the
screwdriver.
6. Install a new battery (3V CR 2032) with
the + facing downwards.
7. Assemble the two halves of the remote
control.
8. Install the key blade.
38
Keys and Remote ControlsE1191904 E1258605