2011 DODGE NITRO Maintaining your vehicle

Cavity CartridgeFuseMini-
Fuse Description
M12 30 Amp
Green Radio, Amplifier
M13 20 Amp
Yellow Ignition Off Draw –
Instrument Cluster,
Wireless Control
Module, SIREN, Mul-
tifunction Control
Switch, Siren – If
Equipped
M14 20 Amp
Yellow Trailer Tow (Export
Only) – If Equipped
M15 20 Amp
Yellow Rearview Mirror, In-
strument Cluster,
Transfer Case Switch,
Multifunction Control
Switch, Tire Pressure
Monitor, Glow Plug
Module – If EquippedCavity Cartridge
FuseMini-
Fuse Description
M16 10 Amp
Red Airbag Module/
Occupant Classifica-
tion Module
M17 15 Amp
Blue Left Front Park &
Side Marker/Left
Tail/License/Park
Lamp
M18 15 Amp
Blue Right Front Park &
Side Marker/Right
Tail/Park/Run Lamp
M19 25 Amp
Natural Automatic Shutdown
#1 and #2
M20 15 Amp
Blue Instrument Cluster
Interior Light, Switch
Bank, Steering Col-
umn Module
7
MAINTAINING YOUR VEHICLE 435

Cavity CartridgeFuseMini-
Fuse Description
M21 20 Amp
Yellow Automatic Shutdown
#3
M22 10 Amp
Red Right Horn
M23 10 Amp
Red Left Horn
M24 25 Amp
Natural Rear Wiper – If
Equipped
M25 20 Amp
Yellow Fuel Pump, Diesel
Lift Pump – If
Equipped
M26 10 Amp
Red Power Mirror Switch,
Driver Window
SwitchCavity Cartridge
FuseMini-
Fuse Description
M27 10 Amp
Red Ignition Switch, Wire-
less Control Module,
Steering Column Lock
– If Equipped
M28 10 Amp
Red Powertrain Control
Module
M29 10 Amp
Red Occupant Classifica-
tion Module
M30 15 Amp
Blue Rear Wiper Module,
Power Folding Mirror
– If Equipped, Diag-
nostic Link
M31 20 Amp
Yellow Back-Up Lamps
M32 10 Amp
Red Airbag Module
436 MAINTAINING YOUR VEHICLE

Cavity CartridgeFuseMini-
Fuse Description
M33 10 Amp
Red Powertrain Control
Module
M34 10 Amp
Red Park Assist/Rear
Camera, Climate Con-
trol System Module,
Headlamp Wash,
Compass, IR Sensor,
Relay Diesel Cabin
Heater, Radiator Fan
Diesel – If Equipped
M35 10 Amp
Red Heated Mirrors – If
Equipped
M36 — —Cavity Cartridge
FuseMini-
Fuse Description
M37 10 Amp
Red Antilock Brakes, Sta-
bility Control System,
Stop Lamp Switch,
Fuel Pump Relay
M38 25 Amp
Natural Door and Liftgate
Lock/Unlock Motors
CAUTION!
•When installing the integrated power module
cover, it is important to ensure the cover is prop-
erly positioned and fully latched. Failure to do so
may allow water to get into the integrated power
module, and possibly result in a electrical system
failure.
(Continued)
7
MAINTAINING YOUR VEHICLE 437

CAUTION! (Continued)
•When replacing a blown fuse, it is important to
use only a fuse having the correct amperage rating.
The use of a fuse with a rating other than indicated
may result in a dangerous electrical system over-
load. If a properly rated fuse continues to blow, it
indicates a problem in the circuit that must be
corrected.
REPLACEMENT BULBS
LIGHT BULBS – InteriorBulb No.
Dome Lamp ......................... TL212–2
Liftgate Lamp ........................... 567
Overhead Console Lamps ............. PLW214–2A
Reading Lamp ...................... WL212–2LIGHT BULBS – Exterior
Bulb No.
Headlamp ......................... 9008 H13
Front Park/Turn ...................... 3157AK
Front Sidemarker ......................... 168
Back-Up ............................. 3057K
Center High Mounted Stoplamp ............. LED
(serviced at an authorized dealer)
Fog Lamp .......................... H10 9145
License Plate Lamp ....................... 168
Rear Tail, Stop, Turn Signal ................3057K
BULB REPLACEMENT
Headlamp
1. Open the hood.
2. Reach behind the headlamp unit in the engine com-
partment to access the headlamp bulb lock ring.
3. Firmly grasp the lock ring on the back of the headlamp
unit housing.
438 MAINTAINING YOUR VEHICLE

4. Rotate the lock ring on the back of the headlamp
housing counterclockwise to unlock it.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
5. Disconnect the electrical connector and replace the
bulb.
Left Front Turn Signal
1. Turn the steering wheel all the way to the right (full
right lock).
2. Remove the door in the left wheel liner by twisting
counter clockwise. Access to the bulb can be gained
through the wheel liner hole. 3. Disconnect the electrical connector.
4. Twist the bulb counter clockwise to remove.
Access Door
7
MAINTAINING YOUR VEHICLE 439

Right Front Turn Signal
1. Open the hood.
2. Reach behind the headlight unit in the engine com-
partment to access the turn signal bulb.
3. Twist the bulb counterclockwise to remove.
4. Disconnect the electrical connector and replace the
bulb.
Front Side Marker
1. Open the hood.
2. Remove the grille assembly as follows:a. Remove eight fasteners.
b. Remove two screws from each headlamp. c. Remove two rivets from the center of the grille.
d. Remove one push pin from the top of each fender.
e. Pull the grille assembly toward you to disconnect
the grille clips to the fender and the headlamp ball-
studs to the front end module.
3. Disconnect electrical connector.
4. Turn the bulb counterclockwise to remove.
Front Fog Lamp (Front Fascia Mounted)
1. Reach under the vehicle to access the back of the front
fog lamp.
2. Disconnect the electrical connector from the front fog
lamp housing.
440 MAINTAINING YOUR VEHICLE

3. Firmly grasp the bulb by the two latches and squeeze
them together to unlock the bulb from the front fog lamp
housing.
4. Pull the bulb straight out from the keyed opening in
the housing.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
Rear Tail, Stop, Turn Signal, and Backup Lamp
1. Open the lift gate.
2. Remove the two push pins.
Push Pins
7
MAINTAINING YOUR VEHICLE 441

3. Pull lamp straight back and disconnect electrical con-
nection.
4. Remove the two screws attaching the backplate to the
lamp assembly.
5. Pull the backplate straight back from the lamp hous-
ing.
6. Disconnect the electrical connector.
7. Remove the bulb from the backplate.Center High Mounted Stop Lamp (CHMSL)
1. Remove the two screws securing the CHMSL.
2. Disconnect the electrical connector and washer hose (if
equipped) from the CHMSL.
3. Replace the CHMSL.
Screw Locations
442 MAINTAINING YOUR VEHICLE