2011 Citroen C6 Owner's Manual

135
V
A
B
and change the bulbs.Note: The tool for undoing thescrews is to be found in the toolbox in the spare wheel. See "Changing a wheel".
REAR CENTRAL LENSAReversing lampBFoglamp
The bulbs for lam
ps Aand Bhavea common bulb-holder. Contact
a CITROËN dealer or a qualifi ed
wor
kshop.
THIRD STOPLAMP
Contact a CITROËN dealer or aqualifi ed workshop.To
gain access to the bulb-holders, open the boot and undo the four
screws on the bodywork. Then lower
the boot lid in order to be able to pull out the two rear lamp units, without
pulling on the electric cables.
NUMBER PLATE
Detach the transparent shield, then pull out the bulb. Bulb: W 5 W.
After each operation,check that the lampswork.
CHANGING BULBS

136
V
A
BC
D
CHANGING BULBS
REAR LATERAL LENSA Parking lamp.
Bulb: W 5 W.
B Stoplamp and parking lamp.
Bulb: P21 W/5 W.
C Direction indicator.
Bulb: P21 W cristal.
DLateral lamp.
Bulb: W 5 W.
1. Open the rear LH fl ap or the two rear RH fl aps, by rotating the pins a
1/4 turn.

137
V
B
C
D
A
CHANGING BULBS
2.Use a tool to detach the twolugs holding the lens.
3.Without touching the seal,
disengage the lamp unit
upwards and orient it so
that the bulbs are pointingoutwards.5.
Reposition the lens, fi rst
inserting the pin furthest forward, then push.Make sure that the rear screen seals and the lamp units arecorrectly located.
6. Secure the two lugs.
4.Replace bulbs that are faulty.

138
V
A
SAFETY RECOMMENDATIONS
It is recommended that towbar installation and removal bedone by a CITROËN dealer or a qualifi ed workshop.
If you are towing another vehicle, the latter must be free-wheeling (gearbox in neutral).
Dimensions(in metres):
A:0.971
TOWBAR
(Boat, caravan, etc.)
It is recommended that towbar installation and removal be done
by a CITROËN dealer or a quali-fi ed workshop.
If you are climbing a steep gradient
and the engine gets excessively
hot, certain functions become una-
vailable (e.g. sequential control of
the automatic gearbox, the air con-
ditioning).
If you are towing, it is necesaary
to deactivate the parking assist-
ance by pressing the control on the
dashboard. See "Parking assist-ance".
It is recommended that
you remove
the towing ball, so that it does not
interfere with the functioning of the
proximity sensors, when you are
not using a trailer.
MAINTENANCE
if cleaning the vehicle with a highpressure system
Your Piloted Defl ector has to be closed.
It is not advisable to clean the
underside of the vehicle, for fear of damaging the electricparking brake.As water may penetrate into
the vehicle interior via the door
apertures, do not target these areas.
Do not direct at the headlamps,
lamps and their edges for too
long or you may damage their coating and seals.
ï
ï
ï
ï

139
V
ROOF BARS
Do not exceed the maximum permittedload.
For the maximum distributed load on theroof bars: see the chapter "General".
Recommendations:Spread the load evenly, avoiding overloading onone side.
Position the heaviest weight as low down as pos-sible.Tie the load down securely and add warning signs
if it is protruding.
Drive conservatively, as the vehicle will be more
vulnerable to side winds.
The stability of your vehicle may be altered.
Remove the roof rack or roof bars when you are
not using them.
•
•
•
•
•
IMPORTANT
For your safety and to avoid damage to the roof, you should use roof bars that are tested and approved by CITROËNfor the design of your particular vehicle.
INSTALLATION
Four fi xing points are provided on your vehicle.

14 0
V
COLD WEATHER SHIELD
After fi tting Before fi tting
FITTING/REMOVAL OF THE
SNOW-GUARD
Fitting
Clip the snow-guard onto the ribs
of the bumper.
Removal
To detach the snow-guard, slide
the tool4 into the recesses in thesnow-guard and lift.Note:The tool 4 is to be found 4in the protection box in the sparewheel. See "Changing a wheel".
The snow-guard delivered with the vehicle (accordingto destination) should be fitted during the winter period,but removed for the remainder of the year.
It is essential to remove it whenever the temperature is above10 °C.

141
V
4
3
8
9
61
2
5
7
CHANGING A WHEEL
ACCESS TO THE SPARE WHEEL
To access the spare wheel1.Lift the boot fl oor by means of the strap.2.Anchor the strap on the roof of the boot.3.To remove the spare wheel, detach the belt then push the wheelforwards so as to be able to lift it.
TO REPOSITION THE SPARE WHEEL
To put the spare wheel back in the boot1.Position the spare wheel fl at in the boot, then pull it towards you.2.Next place the toolbox inside the wheel, then secure the assembly with
the belt.3.Release the strap to return the boot fl oor to its initial position.
Tyre pressures
Tyre pressures are indicated on the label which is positioned low down on
the front pillar. See "Vehicle identifi cation" and "User Precautions". (On this label you will see a pressure for normal speeds and a pressure for high speeds).
1.Handle2.Jack3. Tool for removing/refi tting the
wheel bolts4. Tool for removing the anti-theft
bolt protector
5. Centring guide6. Tool for removing foglamps
and reversing lamps
7. Handle extension8. Towing eye9. Movable chock
TOOLS
The tools are to be found in a pro-
tective holder inside the spare
wheel. Pull back the retaining strap
t
o have access.

142
V
Before positioning the jack, always adjust the vehicle's groundclearance to the "maximum height" position and retain thisadjustment for as long as the jack is under the vehicle (do notuse the hydraulic adjustments).
Never get underneath the vehicle if it is supported only by thejack.
The jack and all the tools are designed specifi cally for use on your particular vehicle. Do not use them for any other applications.
Have the original wheel repaired and refitted as soon aspossible.
It is imperative not to exceed a speed of 80 km/h (50 mph) onthe spare wheel.
REMOVAL1. Park the vehicle on stable, fi rm ground that is not slippery. Apply the
parking brake.2. It is essential to make sure that the occupants have left the vehicle and are in a place where their safety is guaranteed.3. With the engine idling, adjust the ground clearance to maximum height. See "Comfort" and "Ground clearance adjustment". Switch off the igni-
tion and engage fi rst gear or reverse gear depending on any slope (for a vehicle with automatic gearbox, select position P).4. Position the chock at the wheel that is diametrically opposite the one to
be replaced.
5. Position the jack at one of the four jacking-points provided on the sub-
frame close to the wheels, then use the handle to unwind the jack until
it reaches the ground.
6. Slide the removal tool4 into the notch and lever vigorously to detach
the anti-theft bolt protector. See illustration. You can use the handle at
the extremit
y of the tool 4.7.Slacken the wheel bolts.8. Continue to extend the jack until the wheel is a few centimetres off the ground.9. Undo the bolts, remove the wheel.
CHANGING A WHEEL