2011 AUDI TT ROADSTER tow

166 Cleaning and protection
8_ WARNING ,~
Always read and heed all WARNINGS and
other information
Q page 162 .
Plastic and vinyl
Plastics needs special care.
Use a clean, damp clo th or sponge to remove
d ust and light surface dirt . For other soil , use
a lukewarm a ll-purpose clean ing solution or a
mild saddle soap for viny l trim. Remove water
spo ts and soap traces with a clean, damp
clot h or sponge. Use a clean, soft clot h to rub
d ry .
Grease, tar or oil stains can be removed with a
clean cloth or sponge soaked w ith all-purpose
cleaner or with a solvent designed especially
to clean vinyl.
Occasionally apply a colorless vi nyl or leather
preservat ive to reta in the material's l uster
and p liability.
8, WARNING
Always read and heed all WARNINGS and
th e information ¢
page 162.
Aluminum trim
Use only neutral-pH products to remove spots
and depos its from alum in um s urfa ces.
C hrome care produ cts and alkaline cleaners
will attac k alumin um s urfaces and can dam ­
age them over time.
8, WARNING
Always read and heed a ll WARNINGS and
the information
¢ page 162.
Touch-up paint
Minor paint damages should be touched up
immediat ely.
,,. Use e ithe r a to uc h-up p aint s tick or spray
paint to cove r minor scratches and nic ks. Your A
udi dealer has touch -up paint for minor
scratches and sto ne chips. Scratches should
be touched up soon after they occur to pre­
vent corrosion.
T he number for the o rig inal ve hicle paint can
be fo und o n the vehicle identification la bel
¢ page 237.
A WARNING
Always read and heed all WARNINGS and
the information
Qpage 162.
Windows
Clear vision to all sides.
Clean all w indows regular ly to remove road
film and carwash wax buildup .
,,. Remove snow from w indows using a b rush.
,,. Use a pla stic ice s craper to remove ice from
w indows and mi rrors.
,,. Remove othe r residue on the windows w ith
a spray-on g lass cleaner.
,,. Wipe the w indows dry with a clean piece of
cloth or kitc hen paper towel.
The best way to remove snow from windows and mirrors is to use a brush . Use a non-abra­
s ive
plastic ice scraper -better still, a spray
deicer -to remove
ice from w indows and mir­
rors.
T he w indows must not be cleaned with insect
remover or wax since these can inter fere w ith
the function of the windshie ld w iper blades
(chatte r) .
Oil, grease or s ilicone resid ue can be removed
with
glass cleaner or silicone remo ver . How­
ever, wax res idue requires the use of a spec ial­
ly formulated solve nt. Please contact your Au­
di dealer for adv ice on safe products for wax
r emova l.
Windows sh ould also be cleaned on the inside
at regu lar intervals . .,.

creme will nourish and moisturize the
l eather, helping it to b reathe and stay
supple . It also helps to b uild up a protec­
tive coat ing on the surface.
- Clean the leather every 2 -3 months,
and clean any areas that get soiled.
- Remove fresh marks made by ba llpoint
pens, ink, lipstick, shoe polish, etc . as
soon as possib le.
- Preserve the color of the leather as need­
ed by using a special colored leather care
creme to touch up areas of uneven color.
Cleaning and caring for leather
upholstery and trim
App lies to vehicles: with natural leather
Natural leather requires special care and at­
tention .
Normal cleaning
~ Clean soi led areas with a slightly moistened
cotton or woolen cloth.
Mor e stubborn dirt
~ More stubbo rn dirt can be removed using a
cloth saturated with a mi ld soap so lution (2
tablespoons mi ld liquid soap) .
~ Never allow the soap so lution to saturate
the leather, and make certa in that no water
soaks into the seams .
~ Wipe off the soap solution with a soft, dry
cloth .
Cleaning sp ots
~ Remove fresh wa ter-b ase d spots (such as
coffee, tea, ju ices, blood) w ith an absorbent
cloth or paper towel.
~ Remove fresh gr ease or oi l-ba sed spot s
(such as butter, mayonnaise, chocolate) with
an absorbent cloth or paper towe l, or use
the cleane r from the leathe r care kit if the
spot has not yet pene trated into the surface
of the leather .
~ Use an oil/grease dissolving spray, if oil/
grea se spots h ave d ried on.
~ Remove specific kinds of spots (ballpoint
pen, felt marker, fingernail polish, water-
Cleaning and protec tion 17 1
based paint, shoe po lish, etc.) with a spot
remover specifically formu lated for leather .
Le ather car e
~ Every half year use an approved leather care
product (available from your Audi dea ler) to
care for the leathe r.
~ App ly the product very sparingly.
~ Wipe it off with a damp clot h.
If you have any questions about cleaning and
caring for the leather in your vehicle, it is best
to contact your a uthorized Audi dea ler, who
will be g lad to help you and tell you abo ut our
full range of leather care products, such as:
- Leather cleaning and care kit
- Cremes to care fo r colored lea ther
- Spot removers for ballpoint pens, shoe pol-
ish, etc.
- Oil/grease d issolving spray
- New and upcom ing products.
A WARNING
Always read and heed all WARNINGS and
the information <=) page 162.
Q) Note
-Never use chemical so lvents (e.g. lighter
fluid, tu rpentine), waxes, shoe polish or
simi lar products on the leather surfaces
in yo ur Audi .
- T o avoid damage, have stubborn sta ins
removed by a comme rcial clean ing spe­
cialist.
Cleaning Alcantara ® (synthetic suede)
Applies to vehicles: with Alcantara upholstery
Removing dust and dirt
~ Moisten a cloth, squeeze out excess water
and wipe down the seat surfaces.
Removing stains
~ Moisten a cloth with lukewarm water or
w ith diluted
ethyl (rubbing ) alcohol.
~ Dab at the stain . Start at the outs ide and
work inwards . •
•

KG OR XXX LBS"on your vehi­
cle's placard (tire inflation
pressure label)
¢ page 198 ,
fig. 146.
2. Determine the combined
weight of the driver and pas­ s engers that will be riding in
your vehicle .
3. Subtract the combined
weight of the driver and pas ­
s engers from
"XXX" kilo ­
grams or
"XXX " pound s
shown on the sticker
¢ page 198 , fig. 146 .
4. The resulting figure equals
the available amount of car­go and luggage load capa ci­
ty . For example, if the
"XXX''
amount equals 1400 lbs.
and there will be five 150 lbs. passengers in your vehi­
cle, the amount of available
cargo and luggage load ca­
pacity is 650 lbs. (1400-750 (5
X 150) = 650 lbs .)
5. Determine the combined weight of luggage and cargo being loaded on the vehicle.
That weight may not safely
exceed the available cargo
and luggage load capacity
calculated in Step 4.
Tires and wheels 203
6 . If your vehicle will be towing
a trailer , load from your trail­
er will be transferred to your
vehicle. Consult this manual
to determine how this re­ duces the available cargo
and luggage load capacity of
your vehicle.
~check the tire sidewall
(¢ page 205, fig . 150) to de­
termine the designated load rating for a specific tire.
Tire service life
Th e se rvic e lif e of tir es d ep ends on a lot of
differ ent things including proper ins tall atio n
and bal ancin g, corr ect ti re press ure and dr iv­
ing s tyle .
Fig. 148 Tir e t read: t read wea r in dic ato rs (TWI)
f --------
~- ---- --'
Fig. 149 Rotating tir e s for more eve n wea r
Tread Wear Indicator (TWI)
The o rig ina l tires o n yo ur vehi cle have
1/ 16 inch ( 1.6 mm) hig h "wea r in dicato rs"

218 What do I do now?
What do I do now?
Trunk escape handle
In case of an emergency, the rear lid can be
opened from the inside using the trunk es­
cape handle.
Fig. 157 Luggage compartment: Trunk escape handle
... To open the trunk lid pull the handle down
as indicated by the -arrow- ~
fig. 157.
The trunk escape handle inside the storage
compartment is made of fluorescent materia l
to g low in the dark.
A WARNING
The trunk escape handle is to be used only
in an emergency.
Vehicle tool kit
The tools are stored underneath the floor
panel in the luggage compartment.
Fig. 158 Luggage compa rtmen t: vehicle tool kit
... Swing the Luggage compartment floor up­
wards .
... Remove the vehicle tool k it.
The on board tool kit includes: -
Hook for removing wheel covers *
- Plastic clip to remove wheel bo lt covers•
- Wheel bolt wrench
-Alignment pin for changing wheels
- Screwdriver with reversible blade
- Replacement bit (reversible Torx bit for
chang ing lamps)
- Open ended wrench 10 x 13
- Towing eye
Note : some of the on board items listed above
are provided on certain models only or are op­
tiona l extras .
A WARNING ~
-Using a bumper jack to raise the vehicle
will damage the bumper system. The
jack may slip, caus ing injury .
- Never support your vehicle on cinder
b locks, bricks or other objects. These
may not be able to support the load and
could cause injury when they fail.
- Never start or run the eng ine while the
veh icle is supported by the jack.
- If you must work under the vehicle, al­
ways use safety stands specifically de­
signed for th is purpose.
- Never use the hexagonal socket in the
handle of the screwdriver to loosen or
tighten the wheel bolts.
Tire repair
General and safety pointers
Appl ies to vehicles: wit h Tire Mobility Sys tem
Tire repair is intended only for temporary,
short-term use.
Fig. 159 Tire damage for whic h t he Tir e Mob ility Sys-
tem is not suited
II>

Emergency situations
General
This chapter is intended for trained emer­
gency crews and working personnel who
have the necessary tools and equipment to
perform these operations.
Starting by pushing or
towing
(D Note
Vehicles with an automatic transmission
cannot be started by pushing or towing .
Starting with jumper
cables
If necessary, the engine can be started by
connecting it to the battery of another vehi­
cle.
If the engine should fail to start because of a
discharged or weak battery, the battery can be
connected to the battery of
another vehicle,
using a
pair of jumper cables to start the en­
gine.
Jumper cables
Use only jumper cables of sufficiently
largec ross section to safely carry the starter
current. Refer to the manufacturer's specifica­
tions.
Use only jumper cables which have
insulated
termina l clamps and are properly marked for
distinction :
plus(+) cable in most cases colored red
minus(-) cable
i n most cases colored black.
_& WARNING
Batteries contain electricity, ac id, and gas.
Any of these can cause very serious or fatal
injury. Follow the instructions below for
safe handling of your vehicle's battery.
- Always shield you r eyes and avoid lean­
ing over the battery whenever possible.
Emergency situations 231
-A discharged battery can already freeze
at temperatures just below 32 °F (0 °C).
Before connecting a jumper cable, the
frozen battery must be thawed com­
pletely, othe rwise it could explode .
- Do not allow battery acid to contact eyes
or skin . Flush any contacted area with
water immediately .
- Improper use of a booster battery to
start a vehicle may cause an explosion.
- Vehicle batter ies generate explosive gas­
es. Keep sparks, flame and lighted ciga­
rettes away from batteries.
- Do not try to jump start any veh icle w ith
a low ac id level in the battery.
- The voltage of the booster battery must
also have a 12-Volt rating. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged bat­
tery . Use of batteries of different voltage
or substantially different "Ah" rat ing
may cause an exp losion and personal in­
jury.
- Never charge a frozen battery. Gas trap­
ped in the ice may cause an explosion.
- Never charge o r use a battery that has
been frozen . The battery case may have
be weakened.
- Use of batter ies of different voltage or
substantially different capacity (Ah) rat ­
ing may cause an exp losion and injury .
The ca pa city (Ah) of the booster battery
should not be lower than that of the dis­
charged battery.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS¢
page 172, Engine com­
partment.
(D Note
- App lying a higher voltage booster bat­
tery will cause expensive damage to sen­
sit ive electronic components, such as
control units, relays, rad io, etc .
- There must be no electrical contact be­
tween the vehicles as otherwise current
could already start to flow as soon as the
posit ive(+) terminals are connected. ..,. •
•

instructions of the jumper cable
manufacturer. If in doubt, call for road
service.
- Jumper cables must be long enough so
that the vehicles do not touch.
- When connecting jumper cables, make
sure that they cannot get caught in any
moving parts in the engine compart­
ment.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
<=> page 172, Engine com­
partment .
@ Note
Improper hook-up of jumper cables can ru­
in the generator.
-Always connect POSITIVE(+) to POSI­
TIVE(+), and NEGATIVE(-) to NEGATIVE
( - ) ground post of the battery manager
control unit.
- Check that all screw plugs on the battery
cells are screwed in firmly . If not, tighten
plugs prior to connecting clamp on nega­
tive battery terminal.
- Please note that the procedure for con­
necting a jumper cable as described
above applies spec ifically to the case of
your vehicle being jump started. When
you are giving a jump start to another ve­
hicle, do
not connect the negative( -) ca­
ble to the negative(- ) terminal on the
discharged battery@. Instead, securely
connect the negative (-) cable to either a
solid metal component that is firmly bolted to the engine block or to the en­
gine block itself. If the battery that is be­
in g charged does not vent to the outside,
escaping battery gas could ignite and ex­
plode!
Emergency situations 233
Emergency towing
with commercial tow
truck
General hints
Your Audi requires special handling for tow­
ing.
T he following information is to be used by
commercial tow truck operators who know
how to operate their equipment safely.
- Never tow your Audi, towing will cause
damage to the engine and transmission.
- Never wrap the safety chains or winch ca­
ble s around the brake lines .
- To prevent unnecessary damage, your Audi
must be transported with a car carrier
(flatbed truck).
- To load the vehicle on to the flat bed, use
the towing loop found in the vehicle tools
and attach to the front or rear anchorage
<=> page 234 and c:> page 235.
A WARNING
A vehicle being towed is not safe for pas­
sengers. Never allow anyone to ride in a
vehicle be ing towed, for any reason.
-
•
•

234 Emergency situations
Front towing loop
Do not install the front towing loop until it is
needed.
Fig. 176 Front bumper: removing th e grill
Fig. 177 Front bumper: screwing in the tow ing loop
The towline eye fits into the threaded hole lo­
cated on the r ight side of the front bumper
behind the grill .
... Remove the screwdriver and towing loop
from the vehicle toolkit
q page 218 .
... Insert the screwdriver into the slot as shown
and press toward the cente r of the vehicle
¢
fig. 176 . At the same time, pull the grill
forward and out .
.,. Screw the towing loop tight ly into the
threaded hole as far as it will go¢
fig. 177.
When it is no longer needed, unscrew the
towline eye and put it back into the on-board
too lkit. Make sure to have the towline eye
stored in the vehicle at all times.
When installing the grill for the air duct, be
sure that the tabs on the gr ill are first insert­
ed into their guides on the vehicle. Then push
the grill into position .
A WARNING
-If the towing loop is not screwed in as far
as it will go, the thread can pull out when
the veh icle is towed -potent ial risk of an
accident.
Front towing loop
Applies to veh icles: w ith 265 hp engine
Only install the front towing loop when it is
needed .
Fig. 178 Right front sect ion: remov ing the air intake
grille
Fig. 179 Right front sect io n with plast ic cove r
A threaded opening with left-hand threads is
located at the front right of the bumper be·
hind the air intake grille. The towing loop is
installed in this opening .
.,. Remove the screwdriver and the towing loop
from the vehicle tool kit
q page 218.
... Reach through the air intake grille, grip the
hor izontal fins and pull it forward to re­
move.
... Use the screwdriver to pry the plastic cover
off
q fig. 179.
... Install the towing loop in the threaded
opening and tighten it until it stops
q page 234, fig. 177.

Remove the towing loop when you are done
using it and place it back in the vehicle tool
kit . A lways keep the tow ing loop in the vehi­
cle.
When insta lling the air intake grille, insert the
tabs on the grille in the mounts on the vehicle
first . Then press the gri lle in to sec ure it.
A WARNING
If the towing loop is not tightened until it
stops when instal ling, the threads may be
pulled out when tow ing the ve hicle and
t hat could ca use an accident.
Rear towing loop
Do not install the rear towing loop until it is
needed.
Fi g. 180 Right rea r sect ion
Fi g. 18 1 Rea r bumper: screwing in t he tow in g loop
On the r ight side under the rear bumper there
i s a t hreaded hole for the tow ing loop. The
threaded hole is pro tected by a cove r.
"' Remove the towing loop from the ve hicle
toolkit
r:::;,page 218.
"'Press the right side of the cover inward
f orcefully to remove i t from the b umper.
¢fig. 180.
Emergency s itu ations 235
"' Sc rew the towing loop tightly into the
threaded ho le as far as it wi ll go.
When it is no longe r neede d, unscrew the
towing loop and put it back into the vehicle
toolk it . Be sure to have the towing loop sto red
in the vehicle at all times.
A WARNING
If t he tow ing loop is not screwed in as far
as it will go, the thread can pull out when
the vehicle is towed -potent ia l risk of an
accident.
loading the vehicle onto a flatbed truck
I
Fi g. 182 Ve hicle on flatbed truck
Front hook up
"'Align the vehicle wi th t he centerline of the
car carrier ramp.
"' Attach the winch hook to the front towline
eye prev iously insta lled.
Rear hook up
"' Alig n the vehicle wi th the center line of the
car car rier ramp .
"' Attach the winch hook to the rear tow line
eye previous ly insta lled.
(D Tips
Check caref ully to ma ke s ure the hook-up
i s secure before moving the car up the flat­
bed truck ramp.