
16 Instruments and warning/indicator lights
• Continue driving only after the engine cool
ant warning/indicator light goes out.
• Contact your authorized Audi dea ler for as-
sistance if necessary .
I f the engine coolant level is correct, then the
radiator fan may be the cause of the malfunc
tion .
• Coolant temperature too high! Please let
engine run with vehicle stationary
If the indicator light turns on and the mes
sage appears in trailer mode*, let the engine
run at id le for a few minutes to cool down.
A WARNING
-If your veh icle should break down for
mechanical or other reasons, park at a
safe distance from moving traffic, turn
off the engine and turn on the hazard
warning lights
c> page 44, Emergency
flasher .
-
-Never open the hood if you see or hear
steam or coolant escap ing from the en
gine compartment - you risk being scald
ed . Wait until you can no longer see or
hear steam or coo lant escaping.
- The engine compartment of any vehicle
is a dangerous area. Before you perform
any work in the engine compartment,
turn of the engine and allow it to cool.
Follow the warning stickers
<=>page 216,
Engine comportment .
(D Note
Do not continu e driving if the . symbol
illuminates. There is a malfunction in the
engine cooling system -you could damage
your engine.
,f,. Safety belts
This warning/indicator light reminds you to
put on your safety belt.
The . warn ing/ indicato r light illum inates
when the ignition is sw itched on to remind
the driver and any front passenger to put on the safety be
lt. Additionally, an acoustic warn
ing (gong) wi ll also sound.
For more Information
q page 137, ,f,. Safety
belt warning light .
0 Battery
This warning/indicator Light detects a mal
function in the generator or in the vehicle's
electrical system.
T he . warn ing/indicator light i llum inates
whe n you switch on the ignition and must go
out after the engine has started .
• Alternator fault: Battery is not being
charged
If the indicator light turns on and the mes
sage appears, there is a malfunct ion in the
generator or veh icle electrical system.
Drive to your authorized Audi dealer or quali
fied workshop immed iately. Because the veh i
cle battery is discharg ing, turn off all unnec
essary electrical equipment such as the rad io .
Seek professiona l assistance if the battery
charge level is too low.
(•i low battery charge: battery will be
charged while driving
If the indicator light turns on and the mes
sage appears, there may be limited starting
ability .
If this message turns off after a little while,
the battery charged enough while driving.
If the message does not turn off, have your
authorized Aud i dea ler or qualified workshop
correct the malfunction.
~ Engine oil pressure malfunction
The red engine oil pressure warning symbol
requires immediate service or repair. Driving with a low-oil-pressure indication is likely to
inflict severe damage to the engine .
• Switch off engine and check oil level
If the indicator light turns on the message ap-
pears, the oil pressure is too low.
IJI>

Instruments and warning/indicator lights 17
~ Pull off the road.
~ Stop t he vehicle .
~ Turnoff th e engine.
~ Check the engine oil level¢ page 22 7.
~ If the engine oil leve l is too low, add engine
o il ¢
page 227 . Make sure that the oil p res
s ur e warn ing symbol . appears no longe r
i n t he d is pl ay befo re you start d rivi ng aga in .
~ If the engi ne oil leve l is co rrec t and the ind i
ca tor lig ht st ill turn s on , tur n the eng ine off
and do not conti nue d riving . Seek professio
na l assista nce .
@ Tips
- The engine oil pressure symbol. is
not an indicator for a low engine oil lev
el. Do not rely on it. Instead, check the
oil level in your engine at regular inter
vals, preferably each time you refuel,
and always before going on a long trip.
- The yellow oil level warning indication
II requires oil refill or workshop serv
ice without delay. Do not wait until the
red oil p ressure warning. starts to
flash before you respond to the low oil
level warning
Ill. By then, your engine
may already have suffered serious dam
age.
°'!=: ;. Engine oil level
• WARNING: Please add oil immediately
When t he sy mbo l and the dr ive r m essage ap
pear, the oil has to be replenishe d righ t now
¢page 224.
If the indicator lig ht and th e message ap pear,
add engine o il im med iate ly
¢ page 227.
II Add oil, max . x qt (l). You may continue
driving
When the symbo l and the dr iver message ap
pear, add the amo unt of o il appeari ng i n the
d isp lay at the next opportunity ¢
page 224.
@-Steering column lock
• Do not drive vehicle: Steering defective
If the indica tor light turns on and the mes
sage a ppears, t here is an e lectronic steering
column lock malfunct io n. You cannot sw itch
t h e ignit ion on.
D o
not tow yo ur vehicle because it cannot be
stee red. Seek professiona l assistance .
!m Steering lo ck : system fault . Please con
tact dealer
If th e i ndica to r light turns on and the mes
sage appea rs, t here is a n electronic stee ring
column lo ck malfun ction.
D rive to your author ized A udi dealer immed i
ate ly to have th e ma lfunction corr ected .
_&. WARNING
-
Your ve hicle mus t no t be towed i n the
eve nt o f a ma lfunction in t he elec tronic
s teer ing column loc k bec ause i t ca nno t be
steere d due to the locked steerin g. If it is
towe d wit h the steeri ng locke d, there is
the r is k of an accident.
© -Engine start system
• Engine start system fault. Please con
tact dealer
If the indicator light turns on and the mes
sage a ppears, do
not switch the ig nitio n off
because you may not be ab le to sw itch it on
again.
D rive to your authorized A udi dealer immedi
ate ly to have the ma lfunction corrected.
I!! Engine start sy stem fault . Please con
tact dealer
I f th e indica to r li ght tur ns on and the mes
sage a ppea rs, t here is a malf unct io n in the en
gine st art system.
D rive to your author ized A udi dealer imm ed i
ate ly to have th e ma lfuncti on corr ected.
0 Air suspension
• Air suspension: system fault. Can contin-
ue slowly with ma x. 35 mph. .,..

18 Instruments and warning/indicator lights
There is a malfunction that can result in re
stricted driving stability.
Carefully drive at a maximum speed of 35
mph
(60 km/h) to your authorized Audi dealer
or qualified workshop to have the malfunction
corrected.
• Air suspension: service mode. Vehicle
can only be moved with restrictions
Carefully drive to your authorized Audi dealer
or qualified workshop immediately to have
the service mode deactivated.
II Air suspension fault
There is a system malfunction that can result
in restricted driving stability or reduced
ground clearance.
Drive to your authorized Audi dealer immedi
ately to have the malfunction corrected.
II Air suspension: vehicle too low. Ground
clearance reduced
The ground clearance is very low due to a sys
tem malfunction. Wait until the air suspen
sion system has restored normal ground clear
ance. Otherwise, conditions such as an uneven
road surface can lead to vehicle damage.
~/ !f Safety systems
The fl (USA models)!EJ (Canada models) in
dicator light monitors the safety systems e.g.
airbags, pretensioners and illuminates for a
few seconds each time you switch the ignition
on.
If the
I (USA models);EI (Canada models)
indicator light does not go out, or if it illumi
nates while you are driving, or if it starts to
blink, then there is a malfunction somewhere
in the system . If the light does not illuminate
when you switch the ignition on, this also
means there is a malfunction.
A WARNING
If you have a malfunction in the safety sys
tems, contact your authorized Audi dealer
immediately. Otherwise the saftey sys- terns may not work
properly in an acci
dent.
f;.J [J. Electronic stabilization program
(ESP)
This warning/indicator light monitors the
electronic stabilization program.
When you switch the ignition on, the indicator light
G] turns on briefly to check the function.
If the
BJ indicator lamp blinks while driving,
the ESP or ASR (Anti-Slip Regulation) is active
ly regulating.
If the BJ indicator lamp illuminates, the sys
tem has switched the ESP off.
If the indicator light
I turns on, the ESP was
switched to ESP sport mode with the button
[!] c::> page 190. If this is case , you can reacti
vate the ESP by switching the ignition off and
then on again. The warning/indicator light
should go out to show that the system is fully
functional again.
ESP/ABS: fault! See owner's manual
If the indicator light DJ and the ABS indicator
light
m (USA models) ;ii] (Canada models)
turn on and the message appears, there is a
malfunction in the ABS system or electronic
differential lock. This also interrupts the ESP.
The brakes still function with their normal
power, but ABS is not active.
Drive to your authorized Audi dealer immedi
ately to have the malfunction corrected.
If the battery terminals were disconnected
and re-connected, the vehicle was jump start
ed or the battery is very weak, the ESP sensor
system goes through a learning process for
the first few yards. The warning/indicator
light illuminates. The warning/indicator light
goes out as soon as the learning process is
complete.
For more information about the ESP
c::> page 190.

20 Instruments and warning/indicator lights
&_ WARNING
Driving with bad brakes can cause a colli
sion and serious personal injury.
- If the warning light
II and the warning
light
- ll with the message Brake
pads!
comes on in the instrument cluster
display, immediately contact your au
thorized Audi dealer or qualified work
shop to have all brake pads checked or
replaced if necessary.
EPC Electronic power control
This warning/indicator light monitors the
electronic power control .
The~ warning/indicator light (Electronic
Power Control) illuminates when you switch
the ignition on as a function check.
(D Tips
-
If this warning/indicator light illuminates
while you are driving, then there is a mal
function in the engine electronics. Have
the malfunction corrected as soon as pos
sible by your authorized Audi dealer or
qualified repair facility.
O Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) is part
of the On-Board Diagnostic (080 II) system.
The symbol
f-@j lights up when the ignition is
switched on and will turn off after the engine has started and has settled at a constant idle
speed . This indicates that the MIL is working
properly.
The warning light illuminates when there is a
malfunction in the engine electronic system.
Contact your authorized Audi dealer and have
the malfunction corrected.
An improperly closed fuel filler cap may also
cause the MIL light to illuminate
<::> page 220 .
For more information
c::> page 27.
1) - : USA mod els only
!7} Engine speed limitation
Applies to vehicles: with engine speed limitation
lfl Engine speed maximum XXXX RPM
The engine speed is automatically limited to
the speed displayed in the driver information
system. This protects the engine from over
heating.
The engine speed limitation deactivates once
the engine is no longer in the critical tempera
ture range and you have released the accelera
tor pedal once.
If the engine speed limitation was activated
by an engine control malfunction, the indica
tor light~ also turns on. Make sure that the
speed does not go above the speed displayed.
Drive to your authorized Audi dealer immedi
ately to have the malfunction corrected.
~"' Engine oil level
II Add oil, max. x qt (l). You may continue
driving
When the symbol II and driver message ap
pear, add the amount of oil appearing in the
display at the next opportunity
c::> page 22 7.
'"' Engine oil sensor
II Oil level! Sensor defective
If the symbol illuminates, contact your au
thorized Audi dealer and have the oil sensor inspected. Until you have this done , check the
oil level each time you refuel just to be on the
safe side
c::> page 22 7.
Bu Fuel level indicator
Ii Please refuel
If the indicator light turns on for the first
time and the message appears, there are about 4 gallons (15 liters) of fuel left in the
tank. Time to refuel
<::> page 219.
Ii Tank system malfunction! Contact dealer llll>

Instruments and warning/indicator lights 21
If the indicator light turns on and th is mes
sage appears, there is a ma lfunction in the
tank system.
Drive to your authorized Aud i dea ler immedi
ately to have the mal function cor rected .
Ci:> Windshield washer flu id level
fl! Please refill washer fluid
If the symbol illuminates, add windshield
washer fluid to the washer system/headlight
washer system* ~
page 236.
~ Windshield wipers
!I Windshield wiper defective
There is a malfunct ion with the windshield
wipers.
D rive to you r autho rized Aud i deale r immedi
ately to have the mal function cor rected.
~/}D /0$ Defective light bulb warning
I-If the indicator light turns on, a bulb has
failed. The message indicates the location of
the bulb .
ffil-if a fog lamp* has failed, the indicator
light turns on to indicate the location on the
vehicle .
rm-if a rea r fog lamp has failed, the indicator
light turns on to indicate the location on the
vehicle.
Vehicle lights: malfunction
If the message appears, there is a malfunc
tion in the headlights or light switch .
Drive to your authorized Audi dea ler immedi
ately to have the malfunction corrected.
A WARNING
- light bulbs are pressurized and could ex
plode while they are being changed caus
ing serious personal injury.
- Work with due care when handling the
high-voltage section of gas discharge (xenon)
lights. Failure to do so cou ld re
sult in death or serious injury .
(D Tips
Have the b ulb replaced or the connection
repaired by your authorized Audi Service
department.
~(D Headlight range control
II Headlight range control: defective!
If the symbol illuminates, the head light range
control is no longer working properly. Have
the system checked and repaired at your Audi
dealer.
§0 Adaptive Light
App lies to vehicles: wit h Adaptive Lig ht
rJI Audi adaptive light: system fault
If the indicator light turns on and this mes
sage appears, there is a malfunct ion in the
adaptive light system. The headlights still
funct ion.
Go to an authorized dealership to have the
headlights or the control unit for the Adaptive
light repaired.
@> Light/rain sensor
fl Automatic headlights/automatic wipers:
system fault
If the indicator light turns on and this mes
sage appears, the light/rain sensor is not
funct io ni ng correctly .
For safety reasons the low beams are turned
on permanently with the switch in
AUTO.
However, you can continue to turn the lights
o n and off using the light switch . You can st ill
control all functions that are independent of
the rain sensor through the w indshield wiper
l ever.
Contact your authorized Audi dealer as soon
as possible to have the problem corrected .

22 Instruments and warning/indicator lights
~ Dynamic steering
t1r- J Steering: system fault. you can continue
driving
If the indicator light turns on and the mes
sage appears, the steer ing may be more diffi
cult to move or mo re sensitive than usual. The
steer ing wheel may also be at an angle when
driving straight.
Drive slow ly to your author ized Audi dealer or
qual ified workshop to have the malfunction
corrected.
t 1r J Dynamic steering: initialising
If this driver message appears and the ind ica
tor light is flashing on the instrument panel,
dynamic steering is being reinitialized . Once
you start the engine after this is finished, the steering wheel w ill be easy to move . Re-in iti
a lization m ight be necessary if the steering
wheel was moved hard to the left and r ight
while the vehicle was not moving. The display
goes out as soon as initialization is complete.
A WARNING
Have the dynamic steering system mal
function repaired as soon as possible by an authorized Audi dealer or any qualified
workshop - risk of accident!
@ Tips
- The dynamic steering stability systems
are not available in the event of a system
malfunction.
- For additional information on dynamic
steering, refer to
c> page 106.
I- I Sport differential
l'I Sport differential: system fault
There is a malfunction with the sport differen
tial.
Drive to you r authorized Aud i dea ler immedi
ate ly to have the malfunction corrected .
Ill Sport differential: overheating T
he transmission temperature has increased
significantly due to the sporty driving manner .
Drive in a less sporty manner until the tem
perature returns to the normal range and the
indicator light switches of.
A WARNING Co....- -
Contact your authorized Audi dealer or a
qualified workshop if the sport differential
i s faulty or malfunct ioning. The repair
must be performed by trained personnel
using the correct oil in order to ensure
safety .
¢¢ Turn signal s
The indicator light blinks when you use either
turn signal.
Whenever you use the left ll or the right rl
turn s ignal, the indicato r light blinks . When
you use the emergency f lashers, both indica
tor lights flash .
If one of the turn signal light bulbs burn out,
the turn signal will blink twice as fast as nor
mal. Carefully drive to your authorized Aud i
dealer immed iate ly to have the malfunction
corrected. The indicator light does not indi
cate a ma lfunction if a turn signal on the trai l
er or on the vehicle fails in trai ler towing
mode.
(D Tips
For more information on the turn signals,
refer to
c> page 45.
CRUISE /C'J' Cruise control
The warning/indicator light
f;;(l)~i~ (USA mod
els)/ . (Canada models) illuminates when
the cruise control is act ivated
c> page 84 .

Instrument s and warning /indicator lights 23
Driver information
display
Overview
Fig. 4 Driver information system in the in strum ent
cluster
Fig . 5 Display: example of the informat ion line
The driver information system contains infor
mation
@ that is displayed on tabs@
¢ fig. 4 . The following content is possible de
pending on vehicle equipment:
@
Tab
1
®
Content
Vehicle functions :
On-board computer <=;>page 24
Digital speedometer
Efficiency program *
r::!;> page 25
Cruise control* ¢ page 84
Adaptive cruise control and Audi
braking guard*¢
page 86
Audi lane assist* <=> page 95
Display darkened
--~~-
@ ®
Tab Content
2 Indicator lights and messages
Warning when a door, the hood or
the rear lid is not closed
¢page27
3
4
5
6
Service interval display¢ page 26
Speed warning system <=;>page 84
Night vision ass istant* ¢ page 109
Audio/video
Telephone*
Navigation *
Th e second and third tabs are only visible if at
least one indicator light or message is shown
or if that system is sw itched on.
The status line © is located in the bottom
part of the disp lay
¢ fig. 4. It displays the ex
terior temperature, time, selector lever posi
tion, trip odometer and odometer.
For some vehicle functions, you can access the
trip information from the temporary memory
r::!;> page 24 in the line (D ¢ fig . 5 .
&_ WARNING
--
- Never rely exclusively on the outside
temperature display to determine if a
road surface is icy or not. Keep in mind
that road surfaces, especially bridges
and overpasses, could be ice cove red and
slippery even at an outside temperatu re
above 41 °F
(+5 °().
-Always remember, even if the "snow
f la ke" symbo l (ice warning) does not ap
pear in the disp lay, black ice could be on
the road.
-Always reduce your speed and d rive with
special care in cold weather cond itions
when the chance of encountering icy road surfaces increases.
(j) Tips
- At temperatures below 14 °F (+ 5 °C) a
snowflake symbol appears ahead of the
temperature display.
It is intended to re-
mind the driver to pay special attention
~

24 Instruments and warning /indicator lights
to ice on the ro ad ¢ & . If the vehicle is
stationary, o r if you are dr iving at a very
l ow speed, the tempe rat ure shown in the
display might be slightly higher t han the
actua l outside temperature. This is
ca used by the heat being rad iated from
t h e eng ine.
- You can se lect the un its used for temper
atu re, speed and other measurements in
the MMI.
- Fo r information on the audio/video and
nav iga tion* functions, refer to the sepa
r ate MMI owner's manual.
Operation
The driver information system is operated us
ing the buttons on the multifunction steering
wheel.
ffi
------,±.
~
Fig. 6 Multifunct ion steer ing wheel: ope rat ing the driv
e r info rmation system
Fi g. 7 Driver infor mat ion syste m: opening t he veh icle
functio ns me nu
Operating concept
.. Swi tch the ign itio n on.
.. To switch between the tabs, press the ro cker
swi tch @ to the left o r right¢
fig. 6.
.. To access additional in format io n be low or
above, rotate the thumbw heel @ dow n or
up. ..
To confirm a selec tion, press the thumb
wheel @.
Accessing Vehicle functions
.. Sele ct the first tab with the ro cke r swit ch
@.
.. Press the button 1::::L Th e Vehicle function s
menu appears¢ fig . 7.
.. To select a menu item, turn and press t he
thumbwhee l@ .
Resetting values to zero
.. Sele ct the on-board computer / Efficiency
program
menu item in the Vehicle func
tions
men u.
.. You can now select between the long-term
memory and short-term memory.
.. To reset the values in a memory, press and
hold the thumbw heel @ for one second.
The last function selected d isp lays when you
switch the ignition on .
On-board computer
You can ca ll up the followi ng i nformation in
the on -board computer:
- Date
- Dr iv ing t ime (h) from the short-term memo-
ry
- Average consumption in MPG ( l/100 km)
from the short-te rm memory
- Average speed i n mph (km/h) from the
short-te rm memory
- Distance driven in miles (km) from the
short-term memory
- Current fuel consumption in MPG ( l/100
km)
- Short-term memory overview
- Long-te rm memory ove rview
T he short-te rm memory collects dr iv ing in for
mation from the time the ignition is switched
on unti l it is switched off. If you continue driv
ing within two ho urs after switch ing the ign i
tion off, the new values are incl uded when cal
cu lating the cu rrent trip information .
Unli ke the short-term memory, the long-term
memo ry is not erased automatically. Yo u can .,..