2011 AUDI A5 CABRIOLET brakes

Intelligent technology
'-------------------------------------------------
Corrosion
T he re may be a te ndency fo r d irt to build u p on the bra ke pads and
co rrosion to form on the d iscs if the car is not dr iven reg ularly o r only
for short trips with litt le use of the bra kes .
If the brakes a re not used freq uen tly, or if co rrosion has formed o n
the discs, it is advisable to clean off the pads and discs by braking
fir mly a few times from a mode rat ely h igh spee d~ & .
Faults in the brake system
If yo u sh ou ld noti ce a sudden increase in b rake peda l trave l, then one
of the two brake circu its may have failed~& .
Low brake fluid level
Ma lfunctions can occ ur in t he brake system if the brake fluid level is
t oo low. The bra ke f lu id level is moni tore d elec tron ically.
Brake lin ing wear status
Brake lin ing wear may be checked by v isua l inspect ion of the condi­
tion of the brake pads throu gh the open ings in the whee l.
If neces­
sary, the whe el may be removed fo r thi s insp ection~
page 320,
"Changing a w hee l".
& WARNING
• You should perform braking maneuvers for the purpose of
cleaning the brake system only if road conditions permit. Other
road users must not be put at risk - you may cau se an accident!
• Before descending a steep grade, reduce speed and shift trans­
mission into a lower gear or lower driving range. Do not ride the
brakes or hold the pedal down too long or too often . This could
cause the brakes to get hot and diminish braking efficiency.
• Do not "ride the brakes " by resting your foot on the pedal when
you do not intend to brake . This may cause the brakes to overheat ,
premature wear and increased stopping distance.
• Under certain climatic and operating condition s such as
passing through water , driving in heavy rain or after washing the
& WARNING (co ntinued )
vehicle, the effectiveness of the brakes can be reduced . In winter,
ice can ac cumulate on the brake pads, linings, dis cs and drums.
Carefully apply brakes for a test. Brakes will dry and ice coatings
will be cleaned off after a few careful brake appli cations.
• Driving for an extended period of time on salt-covered roads
without u sing your brakes can also affect braking efficiency . Clean
off accumulated salt coating from b rake discs and pads with a few
careful brake applic ations.
• If you damage the front spoiler, or if you install a different
spoiler, be sure the air flow to the front brakes i s not obstructed .
Otherwise the brake system could overheat reducing the effective­
ness of the entire brake system.
• Failure of one brake circuit will impair the braking capability
resulting in an increased stopping di stance. Avoid driving the
vehicle and have it towed to the nearest authorized Audi dealer or
qualified workshop.
n
Brake booster
The b roke boost er odds extra broking po wer.
The bra ke boos ter wor ks wi th v acuum pressure whi ch is crea ted o nly
when the eng ine is ru nning~ &.
& WARNING
• Never let the vehicle roll to a stop with the engine shut off.
• If the brake booster is not working, for example when towing
your vehicle , or because the brake booster has somehow been
damaged, the brake pedal mu st be pressed considerably harder to
make up for the lack of booster assistance. •

Intelligent technology
--------------------------------------------------' '----'----
Functioning of Anti-Lock Brake System
(ABS}
ABS prevents the wheels from locking up under braking.
The ABS contributes effectively to vehicle control since it prevents the
w heels from
locking whe n the brakes are applied . This means t hat t he
vehicle rema ins steerable and is less likely to skid.
With ABS you do not need to pump the brake. Ju st hold the brake
pedal down .
However, do not expect the ABS to shorten braking distance under all
circu mstances. When d riving on gr ave l o r on new ly falle n snow o n top
of icy s urfaces, braking distance may be even longer, therefore, under
t he se c ir cu mstances, i t is especially importa nt that you dr ive slowly
and with great care.
How the ABS system works
An a utomat ic check is made when a speed of about 12 mph (20 km/h)
is reached. When this happens, a pumping noise can be heard.
If an individ ual w heel beg ins to rotate too slow ly in relat ion to vehicle
speed and tends to lock, t he ABS automat ic al ly reduces brake pres­
sure to prevent t hat wheel from locking .
Thi s automatic adjustment process w ill cause a
slight vibrat ion of
t he bra ke ped al and some noises to aler t you th at vehicle s peed mus t
be adapted to existing road and traff ic conditions.
& WARNING
Although the ABS is very effective , always remember that braking
capability i s limited by tire traction . Always adjust your driving
speed acco rding to the road and traffic condition s. Do not let the
extra safety afforded by the ABS tempt you into taking extra risk s.
T he ABS cannot overcome the laws of physics .
Controls and equip­ ment Safety first Vehicle operation
(I] Tips
•
If ABS is no t fun ct io ni ng prope rly, a wa rning light will come on .
See =>
page 15.
• If a fault occurs in the A BS, the EDL is also not functioning . This is
indicated by t he ABS warn ing light .•
Brake assist
Brake assist is designed to achieve the optimum braking
effect.
Bra ke ass ist helps to i ncrease the effe ctive br aking power and thus to
achieve a shorte r stopping distance . If the d river presses the brake
peda l very quickly, brake assist automatically boosts the bra king
force to the max imum level, up to the po int whe re the anti-lock b rake
function (ABS) intervenes to stop t he wheels from locki ng . You
should then keep the br ake peda l pressed unti l the veh icle has braked
to the required speed . Brake ass ist switches itself off as soon as you
re le ase the br ake pedal.
& WARNING
Please remember that the accident risk always increases if you
drive too fast , especially in corners or on a slippery road , or if you
follow the vehicle ahead of you too clo sely. Increased ri sk of an
accident cannot be compensated for even by brake assist , so
alway s maintain a safe speed .•
Vehicle care Do-it-yourself service Technical data

Driving and environment
----------------------------------------------'
New brake pads
- -
Remem ber th at new brake pads do not have a full braking
e ffe ct du ring the first 250 mi les (400 ki lo mete rs) afte r they
are in sta lle d .
N ew br ake pads have to be " burnishe d in" before they have op tim al
grab~ &-
Dur ing the break-in period, you sho uld avoid putting severe loads on
the brakes . Severe loads include, for example, sudden ha rd bra king,
in part icu lar at very high s peeds o r, for example, on mountain passes .
& WARNING
New brake pads don't have the best stopping power and must be
" broken-in " during the in itial 100 to 150 miles (150 to 200 kilo ­
meters) of normal city driving. You can compensate for this by
pressing the brake pedal mor e firmly . This also applies later when
new pads are installed. n
Avoid damaging the vehicle
When yo u are driving on poor roads, or over c urbs, steep ramps, etc.,
ma ke ce rtain that low-lying pa rts su ch as spoilers and exhaust system
parts do not bottom out and get damaged .
This is es peciall y tr ue for veh icle s wi th low-slung chass is (sports
chassis)" and fully loaded vehicles. •
Driving through water on roads
Note the following to avoid vehicle damage w hen drivi ng through
water, fo r examp le on floode d roa ds:
Controls and equip­
ment Safety first Vehicle operation
•
The wate r must not be any higher than the bottom of the vehicle
body .
• Do not drive faster than wa lking speed.
& WARNING
After driving through water , mud , slush , etc ., the brakes may be
slow to take effect because of wet brake rotors and pads . Dry the
brakes first by braking carefully to resto re the full braking effect.
0 Note
Vehicle components such as the engine, transmiss ion, suspension or
ele ct ric al sy stem can be severe ly d amaged by driv ing thro ugh wa ter.
[ i ] Tips
• C heck the de pth o f th e wate r before driving thr oug h it.
• Do not stop the vehicle, drive in reverse or switch the engine off
w he n dr iving throug h wate r.
• Keep in m ind that oncoming vehicles may c reate waves t hat raise
t he water leve l and make it too deep fo r yo ur vehicle t o drive thr oug h
safely.
• Avoid drivi ng through sal t wa ter because it can cause corros io n.
Catalytic converter
It is very important th at your emission control s ystem
( c a ta lytic co n verter) is functionin g proper ly to e nsure
th at y our ve hicl e is ru nn in g in an en vir onm entally sound
m ann er.
- Alwa ys use lead- free g asoline=> p ag e 274, "Fuel sup ply".
- Never ru n the tan k down a ll the way to empty . .,
Vehicle care Do-it-yourself service Technical data

Trailer towing
Driving with a trailer
General information
Your Audi was designed primarily for passenger transpor ­
tation.
If yo u plan to tow a t rai ler, p lease rem emb er that the add itiona l load
wi ll affect durab ility, economy and performance.
T railer tow ing not on ly p laces mo re s tress on the vehicle, it a lso calls
for more concentrat ion from the driver.
For this reason, a lways follow the ope rating and dr iv ing instr uctions
prov ided and use common sense .
Technical requirements
Trailer hitch
Use a weight-carrying hitch conforming to the gross trailer weig ht.
Th e hitch mus t be suitable for yo ur vehicle a nd tra ile r and mus t be
mounted secure ly on the vehicle's chassis at a
technically sound l oca­
t ion. Use only a trailer hitch wi th a remov ab le b all m ount. Alw ays
check w ith the tra iler hitch manufacturer to make sure that you are
using t he cor re ct hi tch.
Do not use a bumper hitch.
The h itch must be installed in such a way t hat it does not interfere
w ith the impa ct-absorbing b umper system. No mod ifi cat ions sho uld
be made to the vehicle exhaust and brake systems. From time to
ti me, chec k tha t all hitc h mou ntin g bol ts rem ain secure ly f aste n ed.
When you a re not tow ing a tra iler, remove the tra iler hitch ba ll
mount. This prevents the hitc h from caus ing damage should yo ur
vehicle be struck from behind=> &.
Controls and equip­
ment Safety first Vehicle operation
Trailer brakes
If your trailer is eq
uipped with a braking system, check to be s ure that
i t confo rm s to all regula tions.
The tra iler hydraulic brake system must not be directly connected to
the vehicle's hydraulic brake system=>& .
Safety chains
Alw ays use safety chains be twee n your vehicle and the trai ler.
Trailer lights
Tr ailer l ights m ust meet all reg ulat io ns. Be su re to check with your
author ized Audi deale r for correct wir ing, switches, and re lays.
Mirrors
If you are unab le to see the traffic behind you us ing the regular
outside m irro rs, then you
must install extended m irro rs. It is impor­
tant that yo u
always have clear vision to the rear.
& WARNING
• If a trailer has electrical b rake s please note that these brakes
are not activated by the factory-fitted control unit -ri sk of acci­
dent!
• After removing the trailer hitch , do not store it in your vehicle.
In case of sudden braking, the hitch could fly fo rward and injure
you or your passengers. •
Operating instructions
Maximum trailer we ight
A trailer for your vehicle is limited to a typical class 1 or class 2 trailer . .,.
Vehicle care Do-it-yourself service Technical data

Trailer towing
"-------------------------------------------------
Trailer load distribution
Be sure the load in the trailer is held securely in pla ce to prevent it
from shifting forward, backward or s ideways.
Never allow a passenger to ride in a trailer => & in "Driving instruc­
tions" on
page 256.
Engine cooling system
Towing a trailer makes the eng ine work harde r. It is important that
the cooling system's performance is up to the additional load. Make
sure that the cooling system has enough fluid.
Tire pressure
When towing a trailer, inflate the tires of your vehicle to the cold tire
pressure listed under "Full load" on the label located either on the
dr iver's side B-pillar (visible when the door is open) or inside the fuel
filler flap . Inflate trailer tires to trailer and tire manufacturers' spec­
ifications.
Lights
The headl ight settings should be checked w ith the trailer attached
before driving off. Check to make sure both vehicle and trai ler lights
are working properly.
Safety chains
Be sure trailer safety cha ins are properly connected from the trailer
to the hitch on the vehicle. Leave enough s lack in the chains to permit
turning corners. When you install safety chains, make sure they will
not drag on the road when you are driving.
T he chains should cross under the trailer tongue to p revent it from
dropping in case of separation from the hitch.
Driving instruct!ons
Driving with a trailer always requires extra care and
consideration.
To obtain the best possible handling of vehicle and trailer,
please note the following:
- Do not tow a loaded trailer when your car itself is not
loaded.
- Be especially careful when passing other veh icles .
- Observe speed limits.
- Do not drive at the maximum permissible speed.
- Always apply brakes early.
- Monitor the temperature gauge .
Weight distribution
Towing a loaded trailer w ith an empty car results in a highly unstable
distr ibution of weight. If this cannot be avoided, drive at very low
speeds only to avo id the r isk of losing steer ing control.
A "balanced" rig is easier to operate and control. Th is means that the
tow vehicle should be loaded to the extent possible and permissible,
wh ile keeping the trailer as light as possible under the c ircumstances.
Whenever possible, trans fer some cargo to the luggage compart ­
ment of the tow vehicle while observing tongue load requirements
and vehicle loading considerations.
Speed
Th e higher the speed, the more difficult it becomes for the driver to
control the r ig . Do not drive at the maximum permiss ible speed.
Reduce your speed even more if load, weather or wind conditions are
unfavorable -part icularly when go ing downhill.
Reduce vehicle speed
immediately i f the trailer shows the slightest
sign of swaying.
Do not try to stop the swaying by accelerating. _,

Observe speed limits. In some areas, speeds for vehicles towing
t railers are lowe r than for regular veh icles.
Always apply brakes early. When dr iv ing downh ill, sh ift in to a lower
gear to use the engine braking effect to slow the vehicle. Use of the
brakes alone can cause them to overheat and fail.
Coolant temperature
The coolant temperature gauge~ page 8 must be observed care­
fully. If the needle moves close to the upper end of the scale, reduce
speed immediately and/or turn off the air conditione r.
If the coolant temperature warning light in the instrument cluster
star ts flashing
-t- , pull off the road, stop and let the engine idle for
about two minutes to prevent heat bu ild-up.
& WARNING
Anyone not properly restrained in a moving vehicle is at a much
greater risk in an accident. Never let anyone ride in your car who is
not properly wearing the restraints provided by Audi. u
Trailer towing tips
Important to know
------------
Your vehicle handles differently when tow ing a tra iler because of the
additiona l weight and different weight distribution. Safety, perfor ­
mance and economy will greatly depend on how carefu lly you load
your trailer and operate your rig .
Before you actua lly tow your trailer, practice turning, stopping and
backing up in an area away from traffic. Keep pract icing until you have
become completely familiar with the way your vehicle-t railer combi­
nation behaves and responds.
Controls and equip­
ment Safety first Vehicle operation
Backing up
is d iff icult and requ ires practice . Backing up with a trailer
generally requires steering action opposite to that when backing up
your vehicle without a trailer.
Maintain a greater distance between your vehicle and the one in front
of you. You will need more room to stop . To compensate fo r the
trailer, you will need a larger than norma l turning radius.
When passing, remember that you cannot accelerate as fast as you
normally would because of the added load. Make sure you have
enough room to pass. After passing, allow plenty of room for you r
trailer before changing lanes again.
Avoid jerky starts, sharp turns or rapid lane changes .
[I) Tips
• Do not tow a trai ler during the break-in per iod of your vehicle.
• If you tow a tra iler, your Audi may requi re more frequent mainte­
nance due to the extra toad~
page 343. •
Parking on a slope
Do not park on a slope with a trailer. If it cannot be
avoided, do so only after doing the following:
When parking:
-Apply the foot brake.
- Have someone place chocks under both the vehicle and the
trailer wheels.
- With chocks in place, slowly release the brakes until the
wheel chocks absorb the load.
- Turn the wheels towards the curb.
- Apply the parking brake .
- Move the se lector lever to
P.
Vehicle care Do-it-yourself service Technical data

-~_C_ le_ a_n_ i_ n_ g=- a_ n_d___. p_ ro_ t_e _c_ t_ i_o _n ___________________________________________ _
Cleaning and protection
General information
Regular care preserves vehicl e val ue.
Any automobile is exposed to industria l fumes, co rrosive road salt,
e tc. A well ca red for Audi c an look lik e new many ye ars after pur cha se.
Regu lar and correct care w ill contribute to mai nta in ing t he bea uty
a nd valu e of your Au di.
Furthermore, good care may be a condition for substantiating a
warranty claim should corrosion damage or paint defects occur.
Yo ur au thori zed Audi d eale r h as a var iety of dedicated vehicle-care
products
and can advise w hich ones to use for clea ning the exterior
a n d inter io r of your ve hicle.
W het her you use products recommended by Aud i or other comme r­
cia lly availab le cleaning agents , please make sure yo u appl y them
co rrectly .
& WARNING
• Cleaning agents may be poisonous . Keep them out of the reach
of children.
• Heed all caution labels .
• Always read directions on the container before using any
product. Follow the directions carefully.
• Most chemical cleaners are concentrated and have to be
diluted .
• Use spot removing fluids only in well ventilated areas.
• Do not use gasoline, kero sene , diesel fuel , nail polish remover
or other volatile fluids . They may be toxic, flammable or
hazardous in other ways. Do not wash, wax or dry the vehicle with
the ign ition on or the engine running .
& WARNING (continued )
• Do not clean the under sides of chassi s, fenders , wheel covers,
etc. without protecting your hands and arms. You may cut your­
self on sharp-edged metal parts.
• Moisture and ice on brakes may impair braking efficiency
~ page 243, "General information ". Test the brakes carefully
each time you wash the vehicle .
'£> For the sake of the environment
Select only envir onmenta lly fr iendly clea ning produc ts . Leftover
cleaning pro ducts sho uld not dis posed of i n the household waste .•
Care of exterior
Washing
F re quent w ashin g protec ts th e vehicle.
T he best protection aga inst env ironmental influences is frequent
w ashi ng and w ax ing. How oft en thi s is requ ired depen ds on :
• How m uch the vehicle is used
• Whe re the ve hicle is parke d (gar age, in the o pen un der tr ees, etc.)
• The seasona l and weather conditions
• Environ mental influences
T he longer bird droppings , insects , tree resin, road and industria l
gr ime, t ar, soo t, road sa lt and o ther ma ter ia ls remain on t he veh icle
body, the more lasti ng their destructive effects w ill be. H igh temper­
atu res cause d by ex pos ure to intense s unlight int ensify the co rrosive
effect, part icu larly when humid ity is high as we ll.
~

____________________________________________ C_l_e _a_ n_ i n--= g=--- a_n_ d----' p,__ r_o _t_ e_ c_ t_ i _o_ n __ lffll
Use on ly spec ia l acid-free cleane rs form ulated for a lloy rims . Safe
pro duc ts a re availa ble at your auth oriz e d Audi dealer. Neve r leave the
cleaner on t he rims longer than specified on t he label. If not rins ed
off promptly, the acid containe d in some cleaners can attack t he
t hreads on the wheel bo lts .
N ever use abrasiv e or metal polish ing cleaning agents .
If the protec­
ti ve coatin g has bee n ch ipp ed, e.g . by kick ed up road dirt, to uch it up
as soon as possible.
& WARNING
• Moisture and ice on brakes may affect braking efficiency
~ page 243, "General information ". Test the brake s carefully
each time you wash the vehicle.
• Always read and heed all WARNINGS and other information
~page 260. •
Body cavity sealing
The bod y cavi ty sealing does not ne ed to be checked.
All body cav ities which cou ld be affected by corrosion have been thor­
oughly pro tected at the factory .
T hi s sealing does not require any inspection or add itiona l treatment .
If any wax shou ld see p ou t of the cavity w hen the ambi ent te mper a­
tu re is high, it can be removed with a plastic scraper and a suitable
s o lve nt.
& WARNING
Solvents can be dangerous.
• Benzine is flammable and toxic . If you use benzine fo r
removing the wax, keep sparks, flame and lighted cigarettes
away . Never dump benzine on the ground , into open streams or
down sewage drains.
Safety first
& WARNING (cont inued )
• Be sure to observe all safety and environmental regulations.
Follow all instructions on the container .
• Always read and heed all WARNINGS and other information
~page 260. •
Chassis
Have t he und erc oat ing checke d for dama ge fr om tim e to
t ime.
The lower body shell of you r Aud i is also thoroug hly protected against
c o rrosion.
Any damage to t he un dercoat ing caused by road haza rds s ho ul d be
repa ired promptly .
& WARNING
Too much undercoating in the wrong places can cause a fire.
• Do not apply additional undercoating or rustproofing on or
near the exhaust manifold, exhau st pipes, catalytic converter or
heat shields. While driv ing, the substance used for undercoating
could overheat and cause a fire.
• Always read and heed all WARNINGS and other information
~page 260 . •
E x haust tail pipes
Road s alt and o ther corrosive m ater ials w ill damage the ma terial i n
the exha ust ta il pipes if they are not cleaned reg ularly. Do not clean
t he t ail pipe s with w heel cleaner, pai nt polish , chr ome polish o r oth er
abras ive cleaners . Clean the ta il pipes w ith car care produc ts that are
s u itable fo r st ainless stee l.
~
Vehicle care Technical data