2011 AUDI A3 technical data

_________________________________________ I_ n_ t_ e_ ll_,igent technology ,__E~-
Battery diagnosis
Battery diagnosis continuously determines the state of the battery.
Sensors determine battery voltage, battery current and battery
temperature. This determines the current state of charge and the
power of the battery .
Idling current management
Idling current management reduces energy consumption while the
vehicle is standing. With the ignition switched off, it controls the
energy supply to the various electrical components. Data from
battery diagnosis is considered.
Depending on the battery's state of charge , individual consumers are
gradually turned off to prevent excessive discharge of the battery and
thus maintain starting capability.
Dynamic energy management
While the vehicle is being driven, dynamic energy management
distributes the energy generated according to the needs of the indi­
v idual components. It regulates consumption, so that more electrical
energy is not being used than is being generated and ensures an
optimal state of charge for the battery.
[ i] Tips
• But even energy management cannot negate the limits of physics.
Consider that the power and life of a battery are limited.
• If starting ability is threatened, you are informed by a warning
=> page 196, "Driver notification in the instrument cluster display". •
What you should know
The highest priority is given to maintaining starting capa­
bility.
The battery is severely taxed in short-distance driving, in city traffic
and during the cold time of year. Abundant electrical energy is
Controls and equip­
ment Safety first Vehicle operation
required, but only a little is generated. It is also critical if the engine
is
not running and electrical components are turned on. In this
instance energy is being consumed but none is being generated .
It is in precisely these situations that you will notice energy manage­
ment actively regulating the distribution of energy.
Vehicle stands for an extended period
If you do not drive your vehicle over a period of several days or weeks,
electrical components are gradually cut back or switched off. This
reduces energy consumption and maintains starting capability over a
longer period.
Take into consideration that when you unlock your vehicle, some
convenience functions, such as the remote key or power seat adjust ­
ment, may not be available. The convenience functions will be avail­
able again when you turn on the ignition and start the engine .
With the engine turned off
If you listen to the radio, for example, with the engine turned off, the
battery is being discharged.
If starting capability is jeopardized due to energy consumption, a
message appears in the driver information display.
You have to start the engine to charge the battery.
With the engine running
Although electrical energy is generated when the vehicle is being
driven, the battery can become discharged. This happens mostly
when little energy is being generated and a great deal consumed and
the battery's state of charge is not optimal.
To bring the energy balance back into equilibrium, consumers which
require especially large amounts of energy are temporarily cut back
or switched off. Heating systems in particular require a great deal of
energy . If you notice, for example , that the heated seats* or the
heated rear window are not heating, they have been temporarily cut
back or switched off. These systems will be available again as soon as
the energy balance has been restored. .,
Vehicle care Do-it-yourself service Technical data

Driving and environment
----------------------------------------------'
Driving and environment
The first 1,000 miles (1,500 km)
and afterwards
New engine
The engine needs to be run-in during the first 1,000 miles
(1,50 0 km) .
For the first 600 miles (1,000 kilometers):
- Do not use fu ll thrott le .
- Do not drive at engine speeds that are more than 2/3 of
the maximimum permitted RP M.
From 600 to 1,000 miles (1 ,000 to 1 ,500
kilometers):
- Speeds can
gradually be increased to the maxim um
perm iss ible road or engine s peed .
During and after break-in period
- Do not r ev the eng ine up to high speeds when it is co ld.
T h is app lies w hether th e t ransmission is in N ( Neutral) o r
1 n gear .
After the break-in period - Do not exceed maximum engine speed under any circum ­
stances.
- U pshift i nto the nex t higher gear
before reach ing t he red
area at t he end of the tachometer scale==>
page 8.
During the first few hours of driving, the engine's interna l friction is
hig her than later w hen all the moving pa rts have been broken in. How
Controls and equip­ ment Safety first Vehicle operation we
ll th is b reak-in p rocess is done depends to a cons iderab le extent on
the way the veh icle is d riven dur ing the f irst 1,000 miles (1,500 kilo­
meters).
0 Note
E x tremely high e ngine speeds are automatic ally reduced. However,
these RPM- limits we re prog rammed for an engine well ru n-in, not a
new e ng ine.
~ For the sake of the environment
Do not drive w it h un necess arily hig h eng ine speeds -up shift ing ea rly
saves f uel, reduces noise and protects the environme nt.•
New tires
If y our veh icle is run nin g on n ew tir es, dr ive parti cula rl y
carefu l for the fi rst 30 0 mil es (500 kil ometer s) af ter fit ting.
& WARNING
New tires tend to be slippery and must also be "broken -in ". Be
sure to remember this dur ing the first 300 miles (500 kilome ­
ter s) . Brake gently. Avoid following closely behind other vehicles
or other situations that might require sudden, hard braking.
u
New brake pads
Remember tha t new brak e pa ds d o no t hav e a fu ll braki ng
eff ect d uri ng the first 250 mi les (400 k ilomet ers) after they
are i nsta lled.
Vehicle care Do-it-yourself service Technical data

_____________________________________________ D _r_ i_v _i_,ng and environment
& WARNING
• Do not park or operate the vehicle in areas where the hot
exhaust sy stem may come in conta ct with dry gra ss, bru sh, fuel
s pill or oth er mater ial wh ich can caus e a fire .
• Do not apply additional under co ating or ru stproofing on or
near the exhaust manifold, exhaust p ipes, catalytic converter or
heat shield s. During driving, the sub stance u sed for undercoating
c ould overheat and cause a fire .
0 Note
• Be aware that j ust one tank fi lling w it h le aded fuel w ill already
seriously degra de the performance of the catalyt ic converter .
• Do not exceed the correct engine o il leve l~
page 23 2.
• Do not dr ive until t he f uel tank be comes comp lete ly empty. The
eng ine could misfire . Unburned fue l cou ld also get into the exhaust
sys tem and t his co uld cause t he ca talyt ic conver ter to ove rhe at.
• Do not t urn off the ignition while the vehicle is moving .
• Do not continue to operate your vehicle under these conditions, as
otherwise fuel can reach the cata lytic converter. This cou ld resu lt in
over heat ing of the converter, req uir ing its rep lacemen t.
• T o ass ure efficient operation of the Emission Contro l System :
- Have your ve hicle maintai ned properly and in accordance with
t he se rvi ce recommenda tions in your Warran ty
& M ain tenance
book let .
- Lack o f prope r mai ntena nce as well as improper use of the
vehicle w ill impa ir the f unct io n of the emission control system and
co uld lead to damage .
<£> For the sake of the environment
Even when the Emission Contro l System is operating p roperly, the
exhaust gas ca n have a sulfur-like exhaust gas smell under some
ope rating states. This depends on the s ulfur content o f the fue l being
Controls and equip­
ment Safety first Vehicle operation
used
. Using a differe nt brand of fuel may help, or filling the tank with
lead-free supe r grade g asoline .•
A pp lies to ve hicle s: with d ie se l pa rtic ul at e f ilte r
Diesel particu ate filter
The diese l particulate filte r filters nearly all of the soot part icles out
of the exhaust. The filte r cleans itself a utomat ically under normal
dr iv ing cond itions . If the fi lter cannot clea n itself (for example,
because you are only driving short distances), the filter becomes
clogged w it h soot and the symbol fo r the diese l particulate fi lter
ill uminates ~
page 34.
& WARNING
• Do not park your vehicle over flammable materials such as
grass or leaves because the high temperature of the diesel partic­
ulate filter could start a fire .
• Do not apply an underbody prot ectant in the exhaust system
area or a fire could start.
[I) Tips
• When the diesel partic ulate f ilter becomes sat urated, the engine
speed increases to approx ima tely 1 ,S00 rpm w hile the vehicle is in
motion to initiate t he cleanin g of the diesel particulate fi lter auto ­
matically w it h out the wa rning lamp ligh ting up. If the war ning lamp
st ill appears, you sho uld drive to a qualified workshop. •
Avoid damaging the vehicle
When you are driving on poor roads, or ove r curbs, steep ramps, etc .,
m ake ce rta in t hat low-ly ing pa rt s such as spoilers and exhaust system
parts do not bottom out and get damaged.
Vehicle care Do-it-yourself service Technical data

Driving and environment
------------------------------------------------'
you start the engine and avoid running at high RPMs while the engine
is still warming up.
0 Note
Do not leave engine idling unattended after starting. If warning
lights should come on to indicate improper operation, they would go
unheeded. Extended idling also produces heat, which could result in
overheat ing or other damage to the vehicle or other property.•
Regular maintenance
A badly tuned engine unnecessarily wastes a lot of fuel.
- Have your vehicle serviced at regular intervals.
By having your vehicle regularly serviced by an authorized Audi dealer
helps to ensure that it runs properly and economically. The condition
of your vehicle not on ly affects its safety and ability to hold its value,
it also affects
fuel consumption .
Check your oil each time you fill your tank.
The amount of oil used is related to engine load and speed.
It is normal for the oil consumption of a new engine to reach its
lowest value after a certain mi leage has been driven.
You must drive you r vehicle about 3,000 miles (5,000 kilometers)
before you can properly assess oil consumption.
Thi s also applies to fuel consumption and engine output.
0 Note
• Have your vehicle maintained properly and in accordance with the
service recommendations in your Warranty
& Maintenance booklet.
Lack of proper maintenance as well as improper use of the vehicle will
impa ir the function of the emission control system and could lead to
damage.
Controls and equip­ ment Safety first Vehicle operation
•
Do not alter or remove any component of the Emission Control
System unless approved by the manufacturer.
• Do not a lter or remove any device, such as heat shie lds, switches,
ignition w ires, va lves, which are designed to protect your vehicle 's
Emission Control System and other important vehicle components.
Fewer short tr ips
Fuel consumption will always be relatively high on short
trips.
- Try to avoid driving short distances with a cold engine.
The engine and catalytic converter have to reach their optimal oper­
ating temperature
to reduce fuel consumption and noxious emis ­
sions effectively .
• Just after starting, a cold eng ine in a mid-size car burns the fuel at
a poor rate of 6-8 miles per gallon (30-40 l/l00km). Half a mile down
the road, the mileage improves to 12 MPG (20 l/100 km). It will take
the engine no less than
two and a half miles (4 km) of driving to
warm up to its proper operat ing temperature and operate at an
economic mileage . This explains why taking the car for sho rt trips is a
rather wasteful convenience .
• Th e
outside temperature is also critical in this regard . Your car
consumes more fuel in the winter than in the summer.
Vehicle care Do-it-yourself service Technical data

Mirrors
If you are unable to see the traffic beh ind you using the regular
outs ide mirrors, then you
must i nstall extended mirrors. It is impor­
tant that you
always have clear vision to the rear.
& WARNING
After removing the trailer hitch, do not store it in your vehicle. In
case of sudden braking, the hitch could fly forward and injure you
or your passengers. •
Operating instructions
Maximum trailer weight
A trailer for your vehicle is lim ited to a typ ical class 1 or class 2 tra iler.
Trailer load distribution
Be sure the load in the trailer is held securely in place to guard aga inst
shifting, be it fo rwa rd, backward or sideways.
Never allow a passenger to ride in a trailer ~ & in "Driving instruc­
tions".
Tire pressure
When towing a tra iler, inflate the tires of yo ur veh icle to the co ld tire
pressure listed unde r "Full load" on the sticker on the right doorjamb.
Inflate trailer tires to trai ler and tire manufacturers' specifications.
Lights
T he headlight settings sho uld be checked with the trailer attached
before driving off . Adjust as necessary so that you can see the road
ahead but not blind oncoming traffic.
Check p roper working of vehicle and tra iler lights.
Controls and equip­
ment Safety first Vehicle operation
Safety
chains
Be sure trailer safety chains are properly connected from the trailer
to the hitch on the vehicle. Leave enough s lack in the chains to permit
turning corners . When you install safety chains, make sure they will
not drag on the road when you are driving.
The chains should cross under the trailer tongue to prevent it from
dropping in case of separation from the hit ch. •
Driving instructions
Driving with a trailer always requires extra care and
consideration.
To obtain the best possible handling of vehicle and trailer,
please note the following:
- Do not tow a loaded trailer when your car itself is not
loaded .
- Be especially careful when passing other vehicles.
- Observe speed limits.
- Do not drive at the maximum permissible speed .
- Always apply brakes early.
- Monitor the temperature gauge.
Weight distribut ion
Towing a loaded trailer with an empty car results in a highly unstable
distribution of we ight. If th is cannot be avoided drive at very low
speeds only to avoid the risk of losing steering control.
A "balanced " rig is easier to operate and control. This means that the
tow vehicle should be loaded to the extent possible and permiss ible
whi le keeping the trai ler as light as possible under the circumstances .
Whenever possible, transfer some cargo to the luggage compart-
Vehicle care Do-it-yourself service Technical data

Parking on a slope
Do not park with a trailer on a slope. If it cannot be
avoided, do so only after doing the following:
When parking:
-Apply the foot brake.
- Have someone place chocks under both the vehicle and the
trailer wheels.
- With chocks in place, slowly release the brakes until wheel
blocks absorb the load.
- Turn the wheels towards the curb.
- Apply the parking brake.
- Place an automatic transmission in
P, respectively a
manual transmission in first or reverse gear.
When restarting after parking:
- Start the engine .
- Shift transmission into gear .
- Release the parking brake and slowly pull out and away from the wheel blocks .
- Stop and have someone retrieve the wheel blocks.
[I] Tips
If you move the selector lever of the automatic transmiss ion to P
before applying the parking brake and before blocking the wheels,
you may have to use more force later to move the leve r out of the
P
position. •
Controls and equip­ ment Safety first Vehicle operation
Vehicle care Do-it-yourself service Technical data

____________________________________________ C_l_e _a_ n_ i n--= g=--- a_n_ d----' p,__ r_o _t_ e_ c_ t_ i _o_ n __ lffll'II
High temperatures, as from exposure to intense sunlight, intensify
the corrosive effect particularly when humidity is high as well.
Under certa in circumstances,
weekly washing may be necessary .
Under other conditions, a month ly washing and waxing may be
adequate.
After the winter, the underside of the vehicle should be thoroughly
washed, preferably in a profess ional car wash.
& WARNING
Always read and heed all WARNINGS and other information
=> page 206.
0 Note
You should remove debris (such as insects) from the headlight lenses
on a regular basis, for example when refueling yo ur vehicle. Never
clean the headlights with a dry cloth or sponge. Use a wet cloth or
sponge. It is best to use soapy wate r.•
Automatic car wash
The vehicle can be washed in almost any modern auto­
matic car wash.
The vehicle paint is so durable that the vehicle can normally be
washed without problems in an automatic car wash. However, the
effect on the paint depends to a large extent o n the design of the
facility, the filtering of the wash water, the type of wash and care
material, e tc. If the paint has a dull appearance after going through
the car wash or is scratched, bring this to the attention of the oper­
ator immediately .
If necessary, use a different car wash.
Before going through a car wash, be sure to take the usual precau­
tions such as closing the windows and panoramic sliding sunroof*.
Remove ante nna if applicable.
Safety first
If you have installed additional accessories on the vehicle - such as
spoilers, roof rack, etc. - it is best to ask the car wash operator if these
should be removed.
& WARNING
Always read and heed all WARNINGS and other information
=>page 206. •
Washing the vehicle by hand
A lot of water is needed when washing a vehicle by hand.
-Before you start wash ing, ma ke sure you have read and
understood the WARNINGS ~
& in "General informa­
tion" on
page 206.
-First soak all dried dirt until it is soft, then rinse it off.
- As you clean your vehicle, start with the roof and work your
way down to the bottom, using a sponge, a sponge glove
or a clean brush.
- Rinse the sponge or the sponge glove often, flushing it
clean each time.
- Use special car shampoo only for very persistent dirt.
- Rinse the car thoroughly with water .
- Use a chamois leather to gently wipe the exter ior dry .
Use a separate sponge for cleaning the whee ls, door s ills and other
regions exposed to road dirt. In this way, you will not scratch the
paint with coarse particles imbedded in the sponge the next time you
wash the car . .,,
Vehicle care Technical data

____________________________________________ C_l_e _a_ n_ i n--= g,___ a_n_ d----' p,___ r_o _t_ e_ c_ t_ i _o_ n __ _
0 Note
To avo id damaging your vehicle, a lways make sure that there i s suffi­
cient distance between the spray head and soft materia ls like r ubber
hoses, plastic part s and sound-de adening mate ria ls. Never aim the
spray head at the same point for a long time . This a lso applies to
cleaning headl ights and painted bumpers. Remembe r: the closer t he
nozzle is to the surface of the mater ia l, the greater the stress on the
mate rial. •
Wa xing
Wax protects the vehicle's paint.
- U se a manua lly applied car wax occas ionally to pro tect t he
pa int.
A good wax coat ing protects the vehicle paint to a la rge extent
agai nst the env ironmen ta l fa ctors liste d un der~
page 20 6,
"Washing" and even against slight scratches.
You can use a liquid car wax to protect yo ur paint as soon as one wee k
after your ve hicle has been delivered .
Even if you regula rly use a
wa xing process in automatic car washes,
we recomme nd that you m anually apply a co at of wax to give the
paint extra protection, part icularly if water no longer beads on t he
cl ean pa int .
Protec t plast ic body parts with car wax in t he same way as the vehicle
body .
Dur ing warm wea ther de ad insec ts te nd t o collec t on t he fron t
bumper and on the forward area of the hood. They a re much easier to
remove from p aint th at is waxed
often.
Safety first
& WARNING
Always read and heed all WARNINGS and other information
:=> page 206 .
0 Note
Do not use car wax on
• matte o r anodized metal trim
• rub ber or rubbe r-like trim .•
Polishing
P olishing restores the gloss to the paint.
P olis h your ve hicl e only if t he pa int has lost its shine and the gloss
cannot be brought back with wax.
If the polish used does not contain preservative compounds, the
paint must be waxed afterwards=> page 209, "Wax ing".
& WARNING
Always read and heed all WARNINGS and other information
:=> page 206 .
0 Note
Do no t trea t matte a nodize d meta l trim, p lastic o r ru bber p arts wi th
polish or wax . •
Trim strips
fv1 etal tri m needs s pec ial care .
For env ironmental reasons, Aud i fabr icates the brig ht trim strips and
trim p ieces from pure chrom ium -free a lum inum. ._
Vehicle care Technical data