2011 Acura TSX steering

Operating the Switches Around the Steering Wheel
Wipers and Washers
108Controls
Wipers and Washers
The windshield wipers and washers can be
used when the ignition switch is in ON
II
.
MIST
The wipers run at high speed until you
release the lever. Wiper switch (OFF, INT, LO, HI)
Change the wiper switch setting according to
the amount of rain. Adjusting the delay
Turn the adjustment ring to adjust the wiper
delay.
Windshield Wipers and Washers NOTICE Do not use the wipers when the windshield is dry.
The windshield will get scratched, or the rubber
blades will get damaged. NOTICE In cold weather, the blades may freeze to the
windshield, becoming stuck.
Operating the wipers in this condition may
damage the wipers. Use the defroster to warm the
windshield, then turn the wipers on.
If the vehicle speeds up while the wipers are
operating intermittently, the length of the wipe
interval shortens. When the vehicle starts moving,
the wipers make a single sweep.
The wiper operation of the shortest delay setting
(
) and the LO setting become the same when the
vehicle speeds up.
Turn the washers off if no washer fluid comes out.
The pump may get damaged.
Long delayShort delay
Washer
Sprays while you pull the lever toward you.
When you release the lever, the wipers make
two or three more sweeps before stopping.
MIST OFF INT: Low speed with
intermittent LO: Low speed wipe HI: High speed wipe Intermittent Time
Adjustment RingPull
to use
washer.

Operating the Switches Around the Steering Wheel
Brightness Control
109
Controls
Brightness Control
When the parking lights are turned on and
the ignition switch is in ON
II
, you can
use the brightness control knob to adjust
instrument panel brightness.
Brighten: Turn the knob to the right.
Dim: Turn the knob to the left.
You will hear the beeper when the brightness
reaches minimum or maximum. The multi-
information display will return to its original
state several seconds after you adjust the
brightness.
Brightness level indicator
The brightness level is shown on the multi-
information display while you are adjusting it.
As the brightness level increases to the right,
the instrument panel gets brighter.
Brightness Control
Instrument panel brightness varies, depending
on whether the exterior lights are on or off. The
instrument panel dims to reduce glare when they
are on.
Pressing either
(information) button
switches the display.
If you turn the knob to the right until the brightness
display is up to max, the beeper sounds. This cancels
the reduced instrument panel brightness when the
parking lights are on.
The brightness can be set differently for when the
exterior lights are on, and when they are off.
Control Knob

Operating the Switches Around the Steering Wheel
Rear Defogger/Heated Door Mirror Button
110Controls
Rear Defogger/Heated Door Mirror Button
Press the rear defogger and heated door
mirror button to defog the rear window and
mirrors when the ignition is in ON
II
.
The rear defogger and heated door mirrors
automatically switch off after 10-30 minutes
depending on the outside temperature.
However, if the outside temperature is 32°F
(0°C) or below, they do not automatically
switch off.
Rear Defogger/Heated Door Mirror Button NOTICE When cleaning the inside of the rear window, be
careful not to damage the heating wires.
It is critical to wipe the window from side to side
along the defogger heating wires.
This system consumes a lot of power, so turn it off
when the window has been defogged.
Also, do not use the system for a long period when
the engine is idling. This may weaken the battery,
making it difficult to start the engine.

Operating the Switches Around the Steering Wheel
Driving Position Memory System*
111
Continued
Controls
Driving Position Memory System
Using the multi-information display, you can disable
the automatic seat adjustment function.
Customization Procedure


P. 8 0
You can cancel the driving position memory link
and customized settings. Press and hold the LOCK
and UNLOCK buttons at the same time. The LED in
the remote transmitter blinks twice and the default
settings are restored.
To turn the memory position link settings back on,
repeat this procedure. The LED will blink once.
Driving Position Memory System
*
You can store two driver's seat positions with the driving position memory system.
When you unlock and open the driver's door with a remote transmitter, the seat
adjusts automatically to one of the two preset positions.
The multi-information display shows you which remote transmitter you used to
unlock the vehicle when you enter.
Driver 1 transmitter is linked to memory button 1. t
Driver 2 transmitter is linked to memory button 2. t
* Not available on all models
Driver 1 Driver 2

Operating the Switches Around the Steering Wheel
Driving Position Memory System*
112Controls
1. Adjust the driver's seat to the desired
position, and turn the ignition switch to
ON
II
.
2. Press the SET button.
You will hear the beeper, and the
memory button indicator light will blink.
3. Press memory button
1
or
2
within five
seconds of pressing the SET button.
Once the seat position has been
memorized, the indicator light on the
button you pressed stays on.
Storing a Position in Memory
Automatic transmission models 1. Move the shift lever to
P
.
All models 2. Apply the parking brake.
3. Press a memory button (
1
or
2
).
You will hear the beeper, and the
indicator light will blink.
The seat will automatically move to the
memorized position. When it has finished
moving, you will hear the beeper, and the
indicator light stays on.
Recalling the Stored Position
Storing a Position in Memory
After you press the SET button, the storing
operation will be canceled when:
You do not press the memory button within five tseconds.
You readjust the seat position before the double- tbeep.
You turn the ignition switch to any position texcept ON
II.
Recalling the Stored Position
The seat will stop moving if you:
Press the SET button, or a memory button ( t
1 or
2).
Adjust the seat position.
t Automatic transmission models Shift into any position except t
P.
Manual transmission models Release the parking brake. t
Memory Button 1
Memory Button 2
Set ButtonMemory Buttons

Operating the Switches Around the Steering Wheel
Adjusting the Steering Wheel
113
Controls
Adjusting the Steering WheelThe steering wheel height and distance from your body can be adjusted so that
you can comfortably grip the steering wheel in an appropriate driving posture.
1. Pull the steering wheel adjustment lever
up.
The steering wheel adjustment lever is
under the steering column.
2. Move the steering wheel up or down, and
in or out. Make sure you can see the instrument
panel gauges and indicators.
3. Push the steering wheel adjustment
lever down to lock the steering wheel in
position. After adjusting the position, make sure
you have securely locked the steering
wheel in place by trying to move it up,
down, in, and out.
Adjusting the Steering Wheel
Make any steering wheel adjustments before you
start driving.
WARNING
Adjusting the steering wheel position
while driving may cause you to lose
control of the vehicle and be seriously
injured in a crash.
Adjust the steering wheel only when the
vehicle is stopped.
To lock
Lever To a d j u s t

Adjusting the Seats
116Controls
Adjusting the Seat Positions

 
 




Adjust the driver's seat as far back as possible
while allowing you to maintain full control of
the vehicle. You should be able to sit upright,
well back in the seat and be able to
adequately press the pedals without leaning
forward, and grip the steering wheel
comfortably. The passenger's seat should be
adjusted in a similar manner, so that it is as
far back from the front airbag in the
dashboard as possible.
Adjusting the Seats
The National Highway Traffice Safety Administration
and Transport Canada recommend that drivers
allow at least 10 inches (25 cm) between the center
of the steering wheel and the chest.
Always make seat adjustments before driving.
WARNING
Sitting too close to a front airbag can
result in serious injury or death if the
front airbags inflate.
Always sit as far back from the front
airbags as possible while maintaining
control of the vehicle.
Horizontal Position
Adjustment
Height Adjustment
(Driver's seat only)
Driver's seat is shownSeat-back Angle
Adjustment

Adjusting the Seats
Adjusting the Seat Positions
117
Continued
Controls
Adjusting the Seat-Backs
Adjusting the Seat-Backs
Adjust the driver's seat-back to a
comfortable, upright position, leaving ample
space between your chest and the airbag
cover in the center of the steering wheel.
The front seat passenger should also adjust
their seat-back to a comfortable, upright
position.
Reclining a seat-back so that the shoulder part of the belt no longer rests against
the occupant's chest reduces the protective capability of the belt. It also increases
the chance of sliding under the belt in a crash and being seriously injured. The
farther a seat-back is reclined, the greater the risk of injury.
WARNING
Reclining the seat-back too far can result
in serious injury or death in a crash.
Adjust the seat-back to an upright
position, and sit well back in the seat. Do not put a cushion, or other object, between the
seat-back and your back.
Doing so may interfere with proper seat belt or
airbag operation.
If you cannot get far enough away from the steering
wheel and still reach the controls, we recommend
that you investigate whether some type of adaptive
equipment may help.