2011 Acura TSX engine oil

Maintenance Under the Hood
Adding Engine Oil
237
Maintenance
Adding Engine Oil
1. Unscrew and remove the engine oil fill cap.
2. Add oil slowly.
3. Reinstall the engine oil fill cap, and tighten
it securely.
4. Wait for three minutes and recheck the
engine oil dipstick.
Adding Engine Oil
If any oil spills, wipe it up immediately. Spilled oil
may damage the engine compartment components. NOTICE Do not fill the engine oil above the upper mark.
Overfilling the engine oil can result in leaks and
engine damage.
6-cylinder models 4-cylinder models
Engine Oil Fill Cap
Engine Oil Fill Cap

Maintenance Under the Hood
Changing the Engine Oil and Oil Filter
238Maintenance
Changing the Engine Oil and Oil FilterYou must change the engine oil and oil filter regularly in order to maintain
the engine's lubrication. The engine may be damaged if they are not changed
regularly.
Change the oil and filter in accordance with the maintenance message on the
multi-information display.
1. Run the engine until it reaches normal
operating temperature, and then turn the
engine off.
2. Open the hood and remove the engine oil
fill cap. 4-cylinder models 3. Remove the bolts on the undercarriage
and remove the under cover. All models 4. Remove the drain bolt and washer from
the bottom of the engine, and drain the oil
into a suitable container.
5. Remove the oil filter and dispose of the
remaining oil.
Changing the Engine Oil and Oil Filter NOTICE You may damage the environment if you do not
dispose of the oil in a suitable way. If you are
changing the oil by yourself, appropriately dispose
of the used oil. Put the oil in a sealed container and
take it to a recycling center. Do not throw the oil
away into a garbage can or onto the ground.
Drain Bolt
Washer
4-cylinder models
Under Cover Bolt
4-cylinder models

Maintenance Under the Hood
Changing the Engine Oil and Oil Filter
239
Maintenance
6. Check that the filter gasket is not stuck to
the engine contact surface.
If it is stuck, you must detach it.
7. Wipe away dirt and dust adhering to the
contact surface of the engine block, and
install a new oil filter.
8. Put a new washer on the drain bolt, then
reinstall the drain bolt. Tightening torque: 29 lbf∙ft (39 N∙m, 4.0
kgf∙m)
9. Pour the recommended engine oil into the
engine. Engine oil change capacity (including
filter):
4-cylinder models 4.2 US qt (4.0 L) 6-cylinder models

4.5 US qt (4.3 L)
10. Reinstall the engine oil fill cap securely
and start the engine.
11. Run the engine for a few minutes, and
then check that there is no leak from the
drain bolt or oil filter.
12 . Stop the engine, wait for three minutes,
and then check the oil level on the
dipstick.
If necessary, add more engine oil.
Changing the Engine Oil and Oil Filter
You will need a special wrench to replace the oil
filter. You can buy this wrench from a dealer.

When installing the new oil filter follow the
instructions supplied with the oil filter.

Reinstall the engine oil fill cap. Start the engine.
The low oil pressure indicator should go off within
five seconds. If it does not, turn off the engine, and
check your work.
Oil Filter
4-cylinder models 6-cylinder models 6-cylinder models
Oil Filter Drain Bolt
Washer

Maintenance Under the Hood
Transmission Fluid
243
Maintenance
1. Park the vehicle on level ground.
2. Remove the bolts with a wrench, then
carefully remove the under cover.
3. Remove the transmission filler bolt and
washer. Carefully feel inside the bolt hole
with your fingers.
Check if the fluid level is up to the edge
of the bolt hole.
4. If the fluid level is not up to the edge
of the bolt hole, add Acura Manual
Transmission Fluid (MTF) until it runs out of
the hole.
5. Put a new washer on the filler bolt, then
reinstall the filler bolt. Tightening torque: 33 lbf∙ft (44 N∙m,
4.5 kgf∙m)
6. Reinstall the under cover with the bolts.
Manual Transmission Fluid
Check the fluid level when the engine is at normal operating temperature.Specified fluid: Acura Manual Transmission Fluid (MTF)
Manual Transmission Fluid
If Acura MTF is not available, you may use the API
certificated SAE 0W-20 or 5W-20 viscosity motor oil
as a temporary measure.
Replace with MTF as soon as possible. Motor
oil does not contain the proper additives for the
transmission and continued use can cause decreased
shifting performance and lead to transmission
damage. Under Cover
Bolt

247
Replacing Light Bulbs
Continued
Maintenance
When replacing, use the following bulbs.
High beam headlight: 60W (HB3)
Low beam headlight: 55W (H1 for halogen bulb Type)
35W (D2S for high voltage discharge type)
High Beam Headlight
6-cylinder models 1. Remove all the engine compartment
covers.
Engine Compartment Covers

P. 2 3 3
Passenger side
All models 2. Remove the engine coolant reservoir.
Headlight Bulbs NOTICE Halogen bulbs get very hot when lit.
Oil, perspiration, or a scratch on the glass can cause
the bulb to overheat and shatter.
The headlight aim is set by the factory, and typically
does not need to be adjusted. However, if you
regularly carry heavy items in the trunk or tow a
trailer, have the aiming readjusted at a dealer or by
a qualified technician.
The HB3 and H1 types are halogen bulbs.
When replacing a bulb, handle it by its base, and
protect the glass from contact with your skin or
hard objects. If you touch the glass, clean it with
denatured alcohol and a clean cloth.
Headlight Bulbs
Engine Coolant
ReservoirEngine Coolant
Reservoir
6-cylinder models 4-cylinder models

Cleaning
Exterior Care
274Maintenance
Applying Wax
A good coat of automotive body wax helps protect your vehicle’s paint from the
elements. Wax will wear off over time and expose your vehicle’s paint to the
elements, so reapply as necessary.
Maintaining the Bumpers and Other Resin Coated Parts
If you get gasoline, oil, engine coolant, or battery fluid on resin coated parts, they
may be stained or the coating may peel. Promptly wipe it away using a soft cloth
and clean water.
Cleaning the Window
Wipe using a glass cleaner.
Maintaining Aluminum Wheels
Aluminum is susceptible to deterioration caused by salt and other road
contaminants. Use a sponge and mild detergent to wipe away promptly.
Be careful not to use harsh chemicals (including some commercial wheel cleaners)
or a stiff brush. They can damage the clear coat of the aluminum alloy wheels that
helps keep the aluminum from corroding and tarnishing.
Applying Wax NOTICE Chemical solvents and strong cleaners can damage
the paint, metal, and plastic on your vehicle. Wipe
up spills immediately. Maintaining the Bumpers and Other Resin Coated Parts
Ask a dealer about the correct coating material
when you want to repair the painted surface of the
parts made of resin. Cleaning the Window
Wires are mounted to the inside of the rear window.
Wipe along the same direction as the wires with a
soft cloth so as not to damage them.

Handling the Unexpected
This chapter explains how to handle unexpected troubles.
To o l s ..................................................... 276
Types of Tools .....................................276
If a Tire Goes Flat ................................ 277
Changing a Flat Tire ........................... 277
Engine Does Not Start
Checking the Engine .......................... 283
Jump Starting ..................................... 284
Shift Lever Does Not Move ............... 287
Overheating ........................................ 288
How to Handle Overheating .............. 288Indicator, Coming On/Blinking
If the Low Oil Pressure Indicator
Comes On ........................................ 290
If the Charging System Indicator
Comes On ........................................ 290
If the Malfunction Indicator Lamp
Comes On or Blinks .......................... 291
If the Brake System Indicator
Comes On ........................................ 292
If the EPS Indicator Comes On ........... 292
If the Low Tire Pressure/ TPMS Indicator
Comes On or Blinks .......................... 293Fuses
Fuse Locations ................................... 294
Inspecting and Changing Fuses .......... 297
Emergency Towing ............................. 298
When You Cannot Unlock the Fuel
Fill Door ............................................. 299
When You Cannot Open the
Trunk .................................................. 300
275

Indicator, Coming On/Blinking
290Handling the Unexpected
If the Low Oil Pressure Indicator Comes On
Reasons for the indicator to come on
Comes on when the engine oil pressure is low. What to do as soon as the indicator comes on
1. Immediately park the vehicle in a safe place.
2. If necessary, turn the hazard warning lights on. What to do after parking the vehicle
1. Stop the engine and let it sit for about one minute.
2. Open the hood and check the oil level.
Add oil as necessary.
3. Start the engine and check the low oil pressure indicator. The light goes out: Start driving again. The light does not go out within 10 seconds: Stop the engine and
contact a dealer for repairs immediately.
If the Charging System Indicator Comes On
Reasons for the indicator to come on
Comes on when the battery is not being charged. What to do when the indicator comes on
Turn the climate control system, rear defogger, and other electrical
systems, and immediately contact a dealer for repairs.
If the Low Oil Pressure Indicator Comes On NOTICE Running the engine with low oil pressure can cause
serious mechanical damage almost immediately. If the Charging System Indicator Comes On
If you need to stop temporarily, do not turn off the
engine. Restarting the engine may rapidly discharge
the battery.