Operating the Switches Around the Steering Wheel
Light Switches
106Controls
Automatic Operation (automatic lighting control)
Automatic lighting control can be used when
the ignition switch is in ON
II
.
When you turn the light switch to
AUTO
,
the headlights and other exterior lights will
switch on and off automatically depending
on the ambient brightness.
Automatic Operation (automatic lighting control)
We recommend that you turn on the lights manually
when driving at night, in a dense fog, or in dark
areas such as long tunnels or parking facilities.
The light sensor is in the location shown below.
Do not cover this light sensor with anything;
otherwise, the automatic lighting system may not
work properly.Light SensorYou can change the AUTO light sensitivity and
automatic lighting off timer setting using the multi-
information display.
Customization Procedure
P. 8 0
Automatic lighting off feature
The headlights, all other exterior lights, and the instrument panel lights turn off
within 15 seconds after you remove the key and close the driver's door.
If you turn the ignition switch to LOCK
0 with the headlight switch on, but do
not open the door, the lights turn off after 10 minutes (3 minutes, if the switch is
in the
AUTO
position).
The lights turn on again when you unlock or open the driver's door. If you unlock
the door, but do not open it within 15 seconds, the lights go off. If you open the
driver's door, you will hear a lights on reminder chime.
Operating the Switches Around the Steering Wheel
Wipers and Washers
108Controls
Wipers and Washers
The windshield wipers and washers can be
used when the ignition switch is in ON
II
.
MIST
The wipers run at high speed until you
release the lever. Wiper switch (OFF, INT, LO, HI)
Change the wiper switch setting according to
the amount of rain. Adjusting the delay
Turn the adjustment ring to adjust the wiper
delay.
Windshield Wipers and Washers NOTICE Do not use the wipers when the windshield is dry.
The windshield will get scratched, or the rubber
blades will get damaged. NOTICE In cold weather, the blades may freeze to the
windshield, becoming stuck.
Operating the wipers in this condition may
damage the wipers. Use the defroster to warm the
windshield, then turn the wipers on.
If the vehicle speeds up while the wipers are
operating intermittently, the length of the wipe
interval shortens. When the vehicle starts moving,
the wipers make a single sweep.
The wiper operation of the shortest delay setting
(
) and the LO setting become the same when the
vehicle speeds up.
Turn the washers off if no washer fluid comes out.
The pump may get damaged.
Long delayShort delay
Washer
Sprays while you pull the lever toward you.
When you release the lever, the wipers make
two or three more sweeps before stopping.
MIST OFF INT: Low speed with
intermittent LO: Low speed wipe HI: High speed wipe Intermittent Time
Adjustment RingPull
to use
washer.
197
Continued
Driving
When Driving
Shifing
Sequential Shift Mode
Use the paddle shifters to change between 1st and 5th gears without removing
your hands from the steering wheel. The transmission will switch to the sequential
shift mode.
When the shift lever is in
D
:
The vehicle will go into the sequential shift mode momentarily, and the gear
position indicator will come on.
Once you start traveling at a constant speed, the sequential shift mode will
automatically switch off, and the gear position indicator will go off.
Hold the
+ paddle shifter for two seconds to return to normal drive.
When the shift lever is in
S
:
The vehicle will go into the sequential shift mode, and the
M
(sequential shift)
indicator and gear position indicator will come on. At speeds of 6 mph (10 km/h)
or less, the vehicle automatically shifts down into 1st gear. It will not automatically
shift up, even if vehicle speed increases.
You can only pull away in 1st or 2nd gear.
When switching out of the sequential shift mode, move the shift lever from
S
to
D
. When the sequential shift mode is canceled, the sequential shift mode
indicator and shift indicator go off.
If a Tire Goes Flat
Changing a Flat Tire
280Handling the Unexpected
WARNING
The vehicle can easily roll off the jack,
seriously injuring anyone underneath.
Follow the directions for changing a tire
exactly, and never get under the vehicle
when it is supported only by the jack.
How to Set Up the Jack
How to Set Up the Jack
Do not use the jack with people or luggage in the
vehicle.
Use the jack provided in your vehicle.
Other jacks may not support the weight
("load") or
their shape may not match.
The following instructions must be followed to use
the jack safely.
Do not use while the engine is running. tUse only where the ground is firm and level. tUse only at the jacking points. tDo not get in the vehicle while using the jack. tDo not put anything on top of or underneath the tjack.
1. Place the jack under the jacking point
closest to the tire to be changed.
2. Turn the end bracket (as shown in the
image) clockwise until the top of the jack
contacts the jacking point.
Make sure that the jacking point tab is
resting in the jack notch.
3. Raise the vehicle, using the extension bar
and the jack handle, until the tire is off the
ground.
Extension Bar
Wheel Nut
Wrench as Jack
Handle