2011 Acura TSX check engine

205
Driving
When Driving
VSA
® (Vehicle Stability Assist), aka ESC (Electronic Stability Control), System
VSA
® On and Off
This button is on the driver side control
panel. To turn the VSA
® system on and off,
press and hold it until you hear a beep.
VSA
® will stop and the indicator will come
on.
To turn it on again, press the
(VSA
® OFF)
button until you hear a beep.
VSA
® is turned on every time you start the
engine, even if you turned it off the last time
you drove the vehicle.
VSA
® (Vehicle Stability Assist), aka ESC (Electronic Stability
Control), System
Without VSA
®, your vehicle will have normal braking
and cornering ability, but it will not have VSA
®
traction and stability enhancement.
In certain unusual conditions when your vehicle gets
stuck in shallow mud or fresh snow, it may be easier
to free it with the VSA
® temporarily switched off.
When the VSA
® system is off, the traction control
system is also off. You should only attempt to free
your vehicle with the VSA
® off if you are not able to
free it when the VSA
® is on.
Immediately after freeing your vehicle, be sure
to switch VSA
® on again. We do not recommend
driving your vehicle with the VSA
® and traction
control systems switched off.
If the low tire pressure/ TPMS indicator comes on or
blinks, the VSA
® system comes on automatically.
In this case, you cannot turn the system off by
pressing the

button.
You may hear a motor sound coming from the
engine compartment while system checks are being
performed immediately after starting the engine or
while driving. This is normal.
VSA
® OFF
Indicator

Braking
Brake System
211
Driving
Foot Brake
Your vehicle is equipped with disc brakes at all four wheels. A power assist helps
reduce the effort needed on the brake pedal. The brake assist system increases the
stopping force when you depress the brake pedal hard in an emergency situation.
The anti-lock brake system (ABS) helps you retain steering control when braking
very hard.
Brake Assist System

P. 2 13
ABS (Anti-lock Brake System)


P. 2 12
Foot Brake
Check the brakes after driving through deep water,
or if there is a buildup of road surface water. If
necessary, dry the brakes by lightly depressing the
pedal several times.
If you hear a continuous metallic friction sound
when applying the brakes, the brake pads need to
be replaced. Have the vehicle checked by a dealer.
Constantly using the brake pedal while going down
a long hill builds up heat, which reduces the brake
effectiveness. Apply engine braking by taking your
foot off the accelerator pedal and downshifting to
a lower gear. With manual transmission use a lower
gear for greater engine braking.
Do not rest your foot on the brake pedal while
driving, as it will lightly apply the brakes and cause
them to lose effectiveness over time and reduce pad
life. It will also confuse drivers behind you.

Braking
ABS (Anti-lock Brake System)
212Driving
ABS (Anti-lock Brake System)
ABS
Helps prevent the wheels from locking up, and helps you retain steering control by
pumping the brakes rapidly, much faster than you.
The electronic brake distribution (EBD) system, which is part of the ABS, also
balances the front-to-rear braking distribution according to vehicle loading.
You should never pump the brake pedal. Let the ABS work for you by always
keeping firm, steady pressure on the brake pedal. This is sometimes referred to as
"stomp and steer."
ABS (Anti-lock Brake System) NOTICE The ABS may not function correctly if you use an
incorrect tire type and size.
When the ABS indicator comes on while driving,
there may be a problem with the system.
While normal braking is not affected, there is a
possibility of the ABS not operating. Have the
vehicle checked by a dealer immediately.
The ABS does not reduce the time or distance it
takes to stop the vehicle. It only helps with steering
control during hard braking.
In the following cases, your vehicle may need more
stopping distance than a vehicle without ABS:
When driving on rough road surfaces, including twhen driving on uneven surfaces, such as gravel
or snow.
When tire chains are installed. tYou may hear a motor sound coming from the
engine compartment while system checks are being
performed immediately after starting the engine or
while driving. This is normal.
ABS operation
The brake pedal may pulsate slightly when the ABS is working. Keep holding the
pedal firmly down. On dry pavement, you will need to press on the brake pedal
very hard before the ABS activates. However, you may feel the ABS activate
immediately if you are trying to stop on snow or ice.
When the vehicle speed goes under 6 mph (10 km/h), the ABS stops.

Maintenance
This chapter discusses basic maintenance.
Before Performing Maintenance
Inspection and Maintenance .............. 222
Safety When Performing
Maintenance .................................... 223
Parts and Fluids Used in
Maintenance Service ........................ 224
Maintenance Minder
™ ........................ 225
Maintenance Under the Hood
Maintenance Items Under the Hood .. 229
Opening the Hood ............................. 231
Recommended Engine Oil .................. 234
Oil Check ........................................... 235
Adding Engine Oil .............................. 237Engine Coolant .................................. 240
Transmission Fluid .............................. 242
Brake/Clutch Fluid .............................. 244
Refilling Window Washer Fluid ........... 246
Replacing Light Bulbs ......................... 247
Checking and Maintaining Wiper
Blades ................................................ 257
Checking and Maintaining Tires
Checking Tires ................................... 259
Tire and Loading Information Label .... 260
Tire Labeling ...................................... 260
DOT Tire Quality Grading
(U.S. Vehicles)
.................................... 262Wear Indicators .................................. 264
Tire Service Life .................................. 264
Tire and Wheel Replacement ............. 265
Tire Rotation ...................................... 266
Winter Tires ....................................... 267
Battery ................................................. 268
Remote Transmitter Care ................... 269
Replacing the Battery ........................ 269
Climate Control System
Maintenance ..................................... 270
Cleaning
Interior Care ........................................271
Exterior Care ...................................... 273
221

227
Maintenance
Continued
Maintenance Minder™
Maintenance Service ItemsCODE Maintenance Main Items
A Replace engine oilt
*1
B Replace engine oilt
*1 and oil filter
Inspect front and rear brakes t
Check parking brake adjustment t
Inspect tie rod ends, steering gear box, and boots t
Inspect suspension components t
Inspect driveshaft boots t
Inspect brake hoses and lines (Including ABS) t
*OTQFDU
BMM
nVJE
MFWFMT
BOE
DPOEJUJPO
PG
nVJET t
Inspect exhaust system t
#
Inspect fuel lines and connections t
#
CODE Maintenance Sub Items
1 Rotate tirest
2 Replace air cleaner elementt
*2
Replace dust and pollen filter t
*3
Inspect drive belt t
33FQMBDF
USBOTNJTTJPO
nVJE t
*4
4 Replace spark plugst
Replace timing belt and inspect water pump t
*5
Inspect valve clearance t
5 Replace engine coolantt
*4: If you drive regularly in mountainous areas or tow a trailer, replace the transmission fluid at 60,000
miles (100,000 km), then every 30,000 miles (48,000 km). (automatic transmission models only)
*5: If you drive regularly in very high temperatures (over 110 °F, 43 °C ), in very low temperatures (under
-20 °F, -29 °C), or tow a trailer, replace every 60,000 miles/100,000 km. (6-cylinder models only)
#: See information on maintenance and emissions warranty. *1: Change the engine oil according to the Maintenance Minder, or annually, whichever comes first.
*2: If you drive primarily in dusty conditions, replace the air cleaner element every 15,000 miles (24,000
km).
*3: If you drive primarily in urban areas that have high concentrations of soot in the air from industry and
from diesel-powered vehicles, replace the dust and pollen filter every 15,000 miles (24,000 km).
Maintenance Service Items
Independent of the Maintenance Minder tinformation, replace the brake fluid every 3 years.
Inspect idle speed every 160,000 miles (256,000 tkm).
Adjust the valves during services A, B, 1, 2, or 3 tonly if they are noisy. Maintenance Minder
Message System Message
Indicator
Main Items
Sub Items

Maintenance Under the Hood
Oil Check
235
Continued
Maintenance
Oil CheckWe recommend that you check the engine oil level every time you refuel.

Park the vehicle on level ground.
Wait approximately three minutes after turning the engine off before you check
the oil.
4-cylinder models 1. Remove the dipstick (orange handle). 6-cylinder models 1. Remove the dipstick (orange loop). All models 2. Wipe the dipstick with a clean cloth or
paper towel.
3. Insert the dipstick back all the way into its
hole.
Oil Check
If it is near or below the lower mark, slowly add oil
being careful not to overfill.
6-cylinder models 4-cylinder models

Maintenance Under the Hood
Adding Engine Oil
237
Maintenance
Adding Engine Oil
1. Unscrew and remove the engine oil fill cap.
2. Add oil slowly.
3. Reinstall the engine oil fill cap, and tighten
it securely.
4. Wait for three minutes and recheck the
engine oil dipstick.
Adding Engine Oil
If any oil spills, wipe it up immediately. Spilled oil
may damage the engine compartment components. NOTICE Do not fill the engine oil above the upper mark.
Overfilling the engine oil can result in leaks and
engine damage.
6-cylinder models 4-cylinder models
Engine Oil Fill Cap
Engine Oil Fill Cap

Maintenance Under the Hood
Changing the Engine Oil and Oil Filter
239
Maintenance
6. Check that the filter gasket is not stuck to
the engine contact surface.
If it is stuck, you must detach it.
7. Wipe away dirt and dust adhering to the
contact surface of the engine block, and
install a new oil filter.
8. Put a new washer on the drain bolt, then
reinstall the drain bolt. Tightening torque: 29 lbf∙ft (39 N∙m, 4.0
kgf∙m)
9. Pour the recommended engine oil into the
engine. Engine oil change capacity (including
filter):
4-cylinder models 4.2 US qt (4.0 L) 6-cylinder models

4.5 US qt (4.3 L)
10. Reinstall the engine oil fill cap securely
and start the engine.
11. Run the engine for a few minutes, and
then check that there is no leak from the
drain bolt or oil filter.
12 . Stop the engine, wait for three minutes,
and then check the oil level on the
dipstick.
If necessary, add more engine oil.
Changing the Engine Oil and Oil Filter
You will need a special wrench to replace the oil
filter. You can buy this wrench from a dealer.

When installing the new oil filter follow the
instructions supplied with the oil filter.

Reinstall the engine oil fill cap. Start the engine.
The low oil pressure indicator should go off within
five seconds. If it does not, turn off the engine, and
check your work.
Oil Filter
4-cylinder models 6-cylinder models 6-cylinder models
Oil Filter Drain Bolt
Washer