2011 Acura TSX remove seats

Seat Belts
Fastening a Seat Belt
30Safe Driving
Lap belt
as low as
possible
3. Position the lap part of the belt as low
as possible across your hips, then pull up
on the shoulder part of the belt so the
lap part fits snugly. This lets your strong
pelvic bones take the force of a crash and
reduces the chance of internal injuries.
4. If necessary, pull up on the belt again to
remove any slack, then check that the belt
rests across the center of your chest and
over your shoulder. This spreads the forces
of a crash over the strongest bones in your
upper body.
Fastening a Seat Belt
To release the belt, push the red PRESS button
then guide the belt by hand until it has retracted
completely.
When exiting the vehicle, be sure the belt is out of
the way and will not get closed in the door.
Adjusting the Shoulder Anchor
The front seats have adjustable shoulder anchors to accommodate taller and
shorter occupants.
1. Move the anchor up and down while
holding the release button.
2. Position the anchor so that the belt rests
across the center of your chest and over
your shoulder.
Adjusting the Shoulder Anchor
The shoulder anchor height can be adjusted to four
levels. If the belt contacts your neck, lower the
height one level at a time.
After an adjustment, make sure that the shoulder
anchor position is secure.
WARNING
Improperly positioning the seat belts can
cause serious injury or death in a crash.
Make sure all seat belts are properly
positioned before driving.
Push

Adjusting the Seats
Adjusting the Seat Positions
119
Continued
Controls
A passenger sitting in the center back seating
position should adjust the height of their
head restraint to an appropriate position
before the vehicle begins moving.
To raise the head restraint:
Pull it upward.
To lower the head restraint:
Push it down while pressing the release
button.
Removing and Reinstalling the Head Restraints
Head restraints can be removed for cleaning or repair.
To remove a head restraint:
Pull the restraint up as far as it will go. Then push the release button, and pull the
restraint up and out.
To reinstall a head restraint:
Insert the legs back in place, then adjust the head restraint to an appropriate
height while pressing the release button. Pull up on the restraint to make sure it is
locked in position.
Removing and Reinstalling the Head Restraints
WARNING
Failure to reinstall the head restraints can
result in severe injury during a crash.
Always replace the head restraints before
driving.
Changing the Center Rear Seat Head Restraint Position

Adjusting the Seats
Rear Seats
123
Controls
Rear Seats
Folding Down the Rear Seats
2. Pull the release lever in the trunk to release
the lock.
Folding Down the Rear Seats
The rear seat-backs can be folded down to
accommodate bulkier items in the trunk.
Never drive with a seat-back folded down and the
trunk lid open.
Carbon Monoxide Hazard


P. 6 0
To lock a seat-back upright, push it backwards until
it locks.
When returning a seat-back to it’s original position,
push it firmly back. Also, make sure all rear shoulder
belts are positioned in front of the seat-back, and
the center shoulder belt is re-positioned in the
guide.
Make sure that the folded seat-back does not press
against the front passenger seat, as this can cause
the weight sensors in the front passenger seat to
work improperly.
Passenger Airbag Off Indicator


P. 4 5
Also make sure all items in the trunk or items
extending through the opening into the rear
seats are properly secured. Loose items can fly
forward if you have to brake hard.
1. Remove the center shoulder belt from the
guide.3. Fold the seat-back down.
If the rear head restraints get caught on the
front seat-backs, remove the head restraints.
Removing and Reinstalling the Head
Restrants P.119
Guide
Center Shoulder BeltRelease Lever