2011 Acura TL Owner's Manual

µ
µ
The SH-AWD torque distribution
monitor on the multi-inf ormation
display shows you the amount of
torque being sent to the wheels.
Each wheel right f ront (RF), lef t
front(LF),rightrear(RR),andleft
rear (LR) has its own torque
indicator. Each torque indicator is displayed as
a bar graph divided into 5 segments.
The number of segments represents
the amount of torque distributed to
each wheel.
When there is only a slight change in
torque distribution while driving,
such as cruising on level roads at the
same speed, the torque distribution
monitor may stop displaying the
amount of torque. This is not a
system problem. The monitor will
show the amount if the system
senses any change in torque
distribution.
While the SH-AWD system helps to
enhance the vehicle’s driving
stability in all situations, it is still
your responsibility to drive and
corner at reasonable speeds and to
leave a sufficient margin of safety. The super handling-all wheel drive
(SH-AWD) system is a f ull time all-
wheel-drive system that
automatically controls and transfers
varying amounts of engine torque to
all wheels independently, according
to the driving conditions.
If equippedSH-AWD T orque Distribution
Monitor
Super Handling-A ll Wheel Drive (SH-A WD)System
478
TORQUE INDICATOR TORQUE INDICATOR
U.S. model is shown.
TM
10/07/29 12:43:30 31TK4620_483
2011 TL

Your vehicle still has normal f ront-
wheel drive with vehicle stability
assist (VSA), but does not have the
advantages of SH-AWD. Have your
vehicle checked by a dealer as soon
as possible.
If the SH-AWD indicator begins to
blink while driving, it indicates the
dif f erential temperature is too high.
You will also see an ‘‘SH-AWD DIFF
TEMP. HIGH’’ message on the
multi-inf ormation display. If this happens, pull to the side of the
road when it is safe, park the vehicle
and shift to Park (automatic), and let
the engine idle until the indicator
goes out. If the indicator does not go
out, take your vehicle to a dealer to
have it checked.
If the SH-AWD indicator on the
instrument panel stays on, and the
‘‘CHECK SH-AWD SYSTEM’’
message also appears on the multi-
inf ormation display, there is problem
with the SH-AWD system.
Super Handling-A ll Wheel Drive (SH-A WD)System
Driving
479
TM
10/07/29 12:43:36 31TK4620_484
2011 TL

Always use the parking brake when
you park your vehicle. Make sure
the parking brake is set f irmly, or
your vehicle may roll if it is parked
on an incline.
If your vehicle has an automatic
transmission, set the parking brake
bef ore you put the transmission in
Park. This keeps the vehicle f rom
moving and putting pressure on the
parking mechanism in the
transmission.Make sure the moonroof and the
windows are closed.
Turn of f the lights.
Place any packages, valuables, etc.,
in the trunk or take them with you.
Lock the doors.
Never park over dry leaves, tall
grass, or other f lammable
materials. The hot three way
catalytic converter could cause
these materials to catch on fire. Check the indicator on the
instrument panel to verif y that the
security system is set.
If the vehicle is f acing uphill, turn
the front wheels away from the
curb. If your vehicle has a manual
transmission, put it in f irst gear.If the vehicle is f acing downhill,
turn the front wheels toward the
curb. If your vehicle has a manual
transmission, put it in reverse gear.
Make sure the parking brake is
f ully released bef ore driving away.
Driving with the parking brake
partially set can overheat or
damage the rear brakes.
If you are unable to stop the
engine normally when the vehicle is
parked (in the Park position on the
automatic transmission models),
see on
page .
186
On models with keyless access system
Parking T ips
Emergency Engine Stop
Parking
480
NOTE:
10/07/29 12:43:45 31TK4620_485
2011 TL

Your vehicle is equipped with disc
brakes at all f our wheels. A power
assist helps reduce the ef f ort needed
on the brake pedal. The emergency
brake assist system increases the
stopping f orce when you depress the
brake pedal hard in an emergency
situation. The anti-lock brake system
(ABS) helps you retain steering
control when braking very hard.
Resting your f oot on the pedal keeps
the brakes applied lightly, builds up
heat, reduces their ef f ectiveness and
reduces brake pad lif e. In addition,
f uel economy can be reduced. It also
keeps your brake lights on all the
time, conf using drivers behind you.Constant application of the brakes
when going down a long hill builds
up heat and reduces their ef f ective-
ness. Use the engine to assist the
brakes by taking your f oot of f the
accelerator and downshif ting to a
lower gear.
Check your brakes af ter driving
through deep water. Apply the
brakes moderately to see if they f eel
normal. If not, apply them gently and
f requently until they do. Be extra
cautious and alert in your driving.
The hydraulic system that operates
the brakes has two separate circuits.
Each circuit works diagonally across
the vehicle (the lef t-f ront brake is
connected with the right-rear brake,
etc.). If one circuit should develop a
problem, you will still have braking
at two wheels.If the brake pads need replacing, you
will hear a distinctive, metallic
screeching sound when you apply
the brake pedal. If you do not have
the brake pads replaced, they will
screech all the time. It is normal f or
the brakes to occasionally squeal or
squeak when you apply them. All f our brakes have audible brake
wear indicators.
Braking System Design Brake Pad Wear Indicators
Braking System
Driving
481
10/07/29 12:43:52 31TK4620_486
2011 TL

The anti-lock brake system (ABS)
helpspreventthewheelsfrom
locking up, and helps you retain
steering control by pumping the
brakes rapidly, much f aster than a
person can do it.
The electronic brake distribution
(EBD) system, which is part of the
ABS, also balances the f ront-to-rear
braking distribution according to
vehicle loading.
Let the ABS work f or you by always
keeping f irm, steady pressure on the
brake pedal. This is sometimes
ref erred to as ‘‘stomp and steer.’’If this indicator comes on, the anti-
lock f unction of the braking system
has shut down. The brakes still work
like a conventional system, but
without anti-lock. You should have
your dealer inspect your vehicle as
soon as possible.
You will f eel a pulsation in the brake
pedal when the ABS activates, and
you may hear some noise. This is
normal: it is the ABS rapidly
pumpingthebrakes.Ondry
pavement, you will need to press on
thebrakepedalveryhardbeforethe
ABS activates. However, you may
feel the ABS activate immediately if
you are trying to stop on snow or ice.
If the ABS indicator comes on while
driving, test the brakes as shown on
page . When the ABS indicator comes on,
you will also see a ‘‘CHECK ABS
SYSTEM’’ message on the multi-
inf ormation display.563
You should never pump the brake pedal.
ABS Indicator
Anti-lock Brakes (ABS)
482
10/07/29 12:43:58 31TK4620_487
2011 TL

If the ABS indicator and the brake
system indicator come on together,
and the parking brake is f ully
released, the EBD system may also
be shut down.
Test your brakes as instructed on
page . If the brakes f eel normal,
drive slowly and have your vehicle
repaired by your dealer as soon as
possible. Avoid sudden hard braking
which could cause the rear wheels to
lock up and possibly lead to a loss of
control.such as trying to take a
corner too f ast or making a sudden
lane change. Always drive at a safe
speed f or the road and weather
conditions.
Always steer moderately
when you are braking hard. Severe
or sharp steering wheel movement
can still cause your vehicle to veer
into oncoming traffic or off the road. on loose
gravel or snow, than a vehicle
without anti- lock.
It only helps with the
steering control during braking.
563 Important Saf ety Reminders
A BS will not prevent a skid that
results f rom changing direction
abruptly,
A BS cannot prevent a loss of
stability. A vehicle with ABS may require a
longer distance to stop
A BS does not reduce the time or
distance it takes to stop the
vehicle.
Anti-lock Brakes (ABS)
Driving
483
10/07/29 12:44:04 31TK4620_488
or uneven surfaces ,such as
2011 TL

The vehicle stability assist (VSA)
system helps to stabilize the vehicle
during cornering if the vehicle
turns more or less than desired. It
also assists you in maintaining
traction while accelerating on loose
or slippery road surfaces. It
does this by regulating the
engine’s output, and by selectively
applying the brakes.
The VSA system cannot enhance the
vehicle’s driving stability in all
situations and does not control your
vehicle’s entire braking system. It is
still your responsibility to drive and
corner at reasonable speeds and to
leave a sufficient margin of safety.When VSA is off, the VSA OFF
indicator comes on as a reminder.
When VSA activates, you will see the
VSA system indicator blink.
If this indicator comes on while
driving, you will also see a ‘‘CHECK
VSA SYSTEM’’ and/or ‘‘CHECK
HILL START ASSIST SYSTEM’’
message on the multi-inf ormation
display. Drive cautiously as the VSA
may not be f unctioning. Without
VSA, your vehicle will have normal
braking and cornering ability, but it
will not have VSA traction and
stability enhancement. Also, the VSA
OFF switch will not operate. Pull to
the side of the road when it is saf e,
and turn of f the engine. Reset the
system by restarting the engine. If
the VSA system indicator stays on,have the VSA system inspected by
your dealer.
When VSA activates, you may notice
that the engine does not respond to
the accelerator in the same way it
does at other times. There may also
be some noise f rom the VSA
hydraulic system. You will also see
the VSA system indicator blink. The main f unction of the
VSA system is generally known as
Electronic Stability Control (ESC).
The system also includes a traction
control f unction.
Vehicle Stability Assist
(VSA ) System Indicator VSA OFF Indicator
Vehicle Stability A ssist (VSA), aka Electronic Stability Control (ESC), System
484
NOTE:
10/07/29 12:44:12 31TK4620_489
2011 TL

This switch is under the driver’s
side vent. To turn the VSA system
on and off, press and hold it
until you hear a beep.
When VSA is off, the VSA OFF
indicator comes on as a reminder.
Press and hold the switch again. It
turns the system back on.
If the low tire pressure/TPMS
indicator comes on (see page ),
or the multi-information display
shows a ‘‘CHECK TPMS SYSTEM’’
message with the indicator flashing
(see page ), the VSA system
automatically turns on even if the
VSA system is turned off with the
VSA OFF switch. In this case, you
cannot turn the VSA system of f by
pressing the VSA OFF switch again.
Without VSA, your vehicle will have
normal braking and cornering ability,
but it will not have VSA traction and
stability enhancement.
If there is a problem with the hill
start assist system, the VSA system
indicator comes on and stays on. The
multi-inf ormation display shows a
‘‘CHECK HILL START ASSIST
SYSTEM’’ message.
With the VSA system indicator on,
you may not be able to stop the
engine even if you park the vehicle
safely. To stop the engine, see
on
page .
186 487
491
CONT INUED
On models with SH-AWD
On models with keyless access systemVSA OFF Switch
Emergency Engine Stop
Vehicle Stability A ssist (VSA), aka Electronic Stability Control (ESC), System
Driving
485
VSA OFF SWITCH
10/07/29 12:44:20 31TK4620_490
2011 TL