2011 Acura TL engine

The automatic transmission will not
allow you to shif t up or down if :If the vehicle speed decreases
below the redline of the selected
lowergearwhiletheindicatoris
f lashing, the transmission
downshif ts, and the indicator
displays the selected gear.
You upshif t bef ore the engine
speed reaches the lowest
threshold of the higher gear.
You pull both paddle shif ters at
thesametime. You downshif t bef ore the engine
speed reaches the highest
threshold of the lower gear.
If you try to do this, the gear
position indicator will f lash the
numberof thelowergearseveral
times, then return to a higher gear.
Downshifting with the paddle shifter
allows you to increase the engine
braking when going down steep or
long hills, and provides more power
when climbing uphills. You can
upshif t the transmission manually to
reduce the rpm.
The transmission remains in the
selected gear (5, 4, 3, 2, or 1).
There is no automatic downshift
when you push the accelerator
pedal to the floor.
When you are driving in 4th or 5th
gear, the transmission downshif ts to
the lower gear under the f ollowing
conditions:
The vehicle slows down to a
certain speed.
You press the brake pedal. The transmission also shif ts
automatically as the vehicle comes to
a complete stop. It downshif ts to f irst
gear when the vehicle speed reaches
9mph(15km/h)orless.
Driving with the Paddle Shif ters (A utomatic Transmission Only)
476
10/07/29 12:43:18 31TK4620_481
2011 TL

´
When you are in sequential shif t
mode, and the vehicle is stopped,
pull the (right) paddle shifter to
shif t to second gear. You will see
‘‘M2’’ in the display. Starting in
second gear helps to reduce
wheelspin in deep snow or on a
slippery surf ace. Drive in the highest gear that lets
the engine run and accelerate
smoothly. This will give you good
f uel economy and ef f ective
emissions control. The f ollowing
shif t points are recommended:
Shif t up
1st to 2nd
2nd to 3rd 3rd to 4th4th to 5th Normal acceleration
15 mph (24 km/h)
25 mph (40 km/h)
40 mph (64 km/h)
45 mph (72 km/h)
Driving with the Paddle Shif ters (A utomatic Transmission Only)
St art ing in Second Gear Recommended Shif t Point s
Driving
477
10/07/29 12:43:23 31TK4620_482
2011 TL

µ
µ
The SH-AWD torque distribution
monitor on the multi-inf ormation
display shows you the amount of
torque being sent to the wheels.
Each wheel right f ront (RF), lef t
front(LF),rightrear(RR),andleft
rear (LR) has its own torque
indicator. Each torque indicator is displayed as
a bar graph divided into 5 segments.
The number of segments represents
the amount of torque distributed to
each wheel.
When there is only a slight change in
torque distribution while driving,
such as cruising on level roads at the
same speed, the torque distribution
monitor may stop displaying the
amount of torque. This is not a
system problem. The monitor will
show the amount if the system
senses any change in torque
distribution.
While the SH-AWD system helps to
enhance the vehicle’s driving
stability in all situations, it is still
your responsibility to drive and
corner at reasonable speeds and to
leave a sufficient margin of safety. The super handling-all wheel drive
(SH-AWD) system is a f ull time all-
wheel-drive system that
automatically controls and transfers
varying amounts of engine torque to
all wheels independently, according
to the driving conditions.
If equippedSH-AWD T orque Distribution
Monitor
Super Handling-A ll Wheel Drive (SH-A WD)System
478
TORQUE INDICATOR TORQUE INDICATOR
U.S. model is shown.
TM
10/07/29 12:43:30 31TK4620_483
2011 TL

Your vehicle still has normal f ront-
wheel drive with vehicle stability
assist (VSA), but does not have the
advantages of SH-AWD. Have your
vehicle checked by a dealer as soon
as possible.
If the SH-AWD indicator begins to
blink while driving, it indicates the
dif f erential temperature is too high.
You will also see an ‘‘SH-AWD DIFF
TEMP. HIGH’’ message on the
multi-inf ormation display. If this happens, pull to the side of the
road when it is safe, park the vehicle
and shift to Park (automatic), and let
the engine idle until the indicator
goes out. If the indicator does not go
out, take your vehicle to a dealer to
have it checked.
If the SH-AWD indicator on the
instrument panel stays on, and the
‘‘CHECK SH-AWD SYSTEM’’
message also appears on the multi-
inf ormation display, there is problem
with the SH-AWD system.
Super Handling-A ll Wheel Drive (SH-A WD)System
Driving
479
TM
10/07/29 12:43:36 31TK4620_484
2011 TL

Always use the parking brake when
you park your vehicle. Make sure
the parking brake is set f irmly, or
your vehicle may roll if it is parked
on an incline.
If your vehicle has an automatic
transmission, set the parking brake
bef ore you put the transmission in
Park. This keeps the vehicle f rom
moving and putting pressure on the
parking mechanism in the
transmission.Make sure the moonroof and the
windows are closed.
Turn of f the lights.
Place any packages, valuables, etc.,
in the trunk or take them with you.
Lock the doors.
Never park over dry leaves, tall
grass, or other f lammable
materials. The hot three way
catalytic converter could cause
these materials to catch on fire. Check the indicator on the
instrument panel to verif y that the
security system is set.
If the vehicle is f acing uphill, turn
the front wheels away from the
curb. If your vehicle has a manual
transmission, put it in f irst gear.If the vehicle is f acing downhill,
turn the front wheels toward the
curb. If your vehicle has a manual
transmission, put it in reverse gear.
Make sure the parking brake is
f ully released bef ore driving away.
Driving with the parking brake
partially set can overheat or
damage the rear brakes.
If you are unable to stop the
engine normally when the vehicle is
parked (in the Park position on the
automatic transmission models),
see on
page .
186
On models with keyless access system
Parking T ips
Emergency Engine Stop
Parking
480
NOTE:
10/07/29 12:43:45 31TK4620_485
2011 TL

Your vehicle is equipped with disc
brakes at all f our wheels. A power
assist helps reduce the ef f ort needed
on the brake pedal. The emergency
brake assist system increases the
stopping f orce when you depress the
brake pedal hard in an emergency
situation. The anti-lock brake system
(ABS) helps you retain steering
control when braking very hard.
Resting your f oot on the pedal keeps
the brakes applied lightly, builds up
heat, reduces their ef f ectiveness and
reduces brake pad lif e. In addition,
f uel economy can be reduced. It also
keeps your brake lights on all the
time, conf using drivers behind you.Constant application of the brakes
when going down a long hill builds
up heat and reduces their ef f ective-
ness. Use the engine to assist the
brakes by taking your f oot of f the
accelerator and downshif ting to a
lower gear.
Check your brakes af ter driving
through deep water. Apply the
brakes moderately to see if they f eel
normal. If not, apply them gently and
f requently until they do. Be extra
cautious and alert in your driving.
The hydraulic system that operates
the brakes has two separate circuits.
Each circuit works diagonally across
the vehicle (the lef t-f ront brake is
connected with the right-rear brake,
etc.). If one circuit should develop a
problem, you will still have braking
at two wheels.If the brake pads need replacing, you
will hear a distinctive, metallic
screeching sound when you apply
the brake pedal. If you do not have
the brake pads replaced, they will
screech all the time. It is normal f or
the brakes to occasionally squeal or
squeak when you apply them. All f our brakes have audible brake
wear indicators.
Braking System Design Brake Pad Wear Indicators
Braking System
Driving
481
10/07/29 12:43:52 31TK4620_486
2011 TL

The vehicle stability assist (VSA)
system helps to stabilize the vehicle
during cornering if the vehicle
turns more or less than desired. It
also assists you in maintaining
traction while accelerating on loose
or slippery road surfaces. It
does this by regulating the
engine’s output, and by selectively
applying the brakes.
The VSA system cannot enhance the
vehicle’s driving stability in all
situations and does not control your
vehicle’s entire braking system. It is
still your responsibility to drive and
corner at reasonable speeds and to
leave a sufficient margin of safety.When VSA is off, the VSA OFF
indicator comes on as a reminder.
When VSA activates, you will see the
VSA system indicator blink.
If this indicator comes on while
driving, you will also see a ‘‘CHECK
VSA SYSTEM’’ and/or ‘‘CHECK
HILL START ASSIST SYSTEM’’
message on the multi-inf ormation
display. Drive cautiously as the VSA
may not be f unctioning. Without
VSA, your vehicle will have normal
braking and cornering ability, but it
will not have VSA traction and
stability enhancement. Also, the VSA
OFF switch will not operate. Pull to
the side of the road when it is saf e,
and turn of f the engine. Reset the
system by restarting the engine. If
the VSA system indicator stays on,have the VSA system inspected by
your dealer.
When VSA activates, you may notice
that the engine does not respond to
the accelerator in the same way it
does at other times. There may also
be some noise f rom the VSA
hydraulic system. You will also see
the VSA system indicator blink. The main f unction of the
VSA system is generally known as
Electronic Stability Control (ESC).
The system also includes a traction
control f unction.
Vehicle Stability Assist
(VSA ) System Indicator VSA OFF Indicator
Vehicle Stability A ssist (VSA), aka Electronic Stability Control (ESC), System
484
NOTE:
10/07/29 12:44:12 31TK4620_489
2011 TL

This switch is under the driver’s
side vent. To turn the VSA system
on and off, press and hold it
until you hear a beep.
When VSA is off, the VSA OFF
indicator comes on as a reminder.
Press and hold the switch again. It
turns the system back on.
If the low tire pressure/TPMS
indicator comes on (see page ),
or the multi-information display
shows a ‘‘CHECK TPMS SYSTEM’’
message with the indicator flashing
(see page ), the VSA system
automatically turns on even if the
VSA system is turned off with the
VSA OFF switch. In this case, you
cannot turn the VSA system of f by
pressing the VSA OFF switch again.
Without VSA, your vehicle will have
normal braking and cornering ability,
but it will not have VSA traction and
stability enhancement.
If there is a problem with the hill
start assist system, the VSA system
indicator comes on and stays on. The
multi-inf ormation display shows a
‘‘CHECK HILL START ASSIST
SYSTEM’’ message.
With the VSA system indicator on,
you may not be able to stop the
engine even if you park the vehicle
safely. To stop the engine, see
on
page .
186 487
491
CONT INUED
On models with SH-AWD
On models with keyless access systemVSA OFF Switch
Emergency Engine Stop
Vehicle Stability A ssist (VSA), aka Electronic Stability Control (ESC), System
Driving
485
VSA OFF SWITCH
10/07/29 12:44:20 31TK4620_490
2011 TL