2011.5 Citroen DS4 RHD ECO mode

The system is reactivated automaticallyat every new star t using the key.
Reactivation

This system requires a specific battery with aspecial specification and technology (reference numbers available from a CITROËN dealer or
a qualified workshop).
Fitting a battery not listed by CITROËN
introduces the risk of malfunction of the system. In the event of a malfunction with the s
ystem,
the "ECO OFF"switch warning lamp flashes,
then comes on continuously.
have it checked by a CITROËN dealer or a qualified workshop.


Operating fault
Maintenance

Before doing anything under the bonnet, deactivate the Stop & Start system to avoid any risk of injury resulting from automatic operation of STA R T mode.

The Stop & Star t system makes use of advanced technology. All work on this type of battery must be done only by a CITROËN dealer or a qualifiedworkshop. Pr
ess the "ECO OFF"switch again.
The system is active again; this is confirmed
by the switch warning lamp going off and the
display of a message.
In the event of a fault in STOP mode, thevehicle may stall. All of the instrumentpanel warning lamps come on.Depending on version, an alert message may also be displayed askingyou to put the gear lever into position Nand put your foot on the brake pedal.
It is then necessary to switch off the ignition, then restart the engine using the key.

) Turn dial 1
to the "LIMIT"
position: the
speed limiter mode is selected but is not
switched on
(Pause). You do not have to switch the speed limiter on
in order to set the speed.) Set the speed value by pressing button 2or 3(e.g.: 55 mph (90 km/h)).
Programming
You can then change the programmed speed using buttons 2
and 3:- by + or - 1 mph (km/h) = shor t press,
- in steps of + or - 5 mph (km/h) = maintained press.
If speed memorisation is available and activated on your vehicle, theprogrammed speed will stop at the closest memorised speed; refer to thecorresponding paragraph. )Switch the speed limiter on by pressing button 4 . )Switch the speed limiter off by pressing button 4: the display confirms that it has been switched off (Pause).)Switch the speed limiter back on by pressing button 4
again.

Exceeding the programmed speed
Pressing the accelerator pedal to exceed the programmed speed will not have any effect unless you press the pedal firmlypast the ypoint of resistance
.
The speed limiter is deactivated temporarily and the programmed speed,
which is still displayed, flashes.
Returning to the programmed speed, by means of intentional or unintentional
deceleration of the vehicle, automatically cancels the flashing of the programmed speed.
On a steep descent or in the event of sharp acceleration, the speed limiter will not be able to prevent the vehiclefrom exceeding the programmed speed. To a v o i d a ny risk of jamming of the pedals:


- ensure that the mat is positioned correctly,

- do not fit one mat on top of another.



Exiting the speed limiter mode
)Turn dial 1to the "0"
position: the speed
limiter mode is deselected. It disappears
from the screen.



Operating fault

In the event of a fault with the speed limiter,
the speed is cleared resulting in flashing of the dashes.
Have it checked by a CITROËN dealer or a qualified workshop.

221Driving





Cruise control
System which automatically maintains thespeed of the vehicle at the value programmed
by the driver, without any action on the
accelerator pedal.
The
functions of this system are grouped
together on the steering mounted controls.
1
.Cruise control mode selection dial.
2. Speed programming/value decreasebutton.3.
Speed programming/value increase button.4.
Cruise control off/resume button.
5. Memorised speeds display button.(see "Memorising speeds")
Steering mounted controls
The cruise control system cannot, in any
circumstances, replace the need to respect speed limits, nor can it replace the need for vigilance and responsibility on the par t of the driver.
You are advised to keep your feet near the pedals at all times.

The programmed information is grouped
together in the instrument panel screen.
6
. Cruise control off/resume indication.
7.Cruise control mode selection indication. 8. Programmed speed value.9.Selecting a stored speed.
(see "Storing speeds")

Displays in the instrument panel


Operation

The cruise control is switched on
manually: it
requires a minimum vehicle speed of 25 mph
(40 km/h) and engagement of:


- fourth gear on the manual gearbox,

- second gear on the electronic gearbox system or automatic gearbox, in sequentialdriving mode,

- position A
on the electronic gearboxsystem or Don an automatic gearbox.
The cruise control is switched off
manually for by pressing the brake or clutch pedal or
on triggering of the ESP system for safety reasons.
It is possible to exceed the programmed speed
temporarily by pressing the accelerator pedal.
To return to the programmed speed, simply
release the accelerator
pedal.
Switching off the ignition cancels any programmed speed value.

Programming
)Turn dial 1 to the "CRUISE"
position: thecruise control mode is selected but is not
switched on (Pause).)Set the programmed speed by accelerating
to the required speed, then press button 2or 3(e.g.: 70 mph (11 0 k m / h)); the cruisecontrol system is activated (ON).
You can then chan
ge the programmed speed using buttons 2 and 3
:
- by + or - 1 mph (km/h) = shor t press,
- in steps of + or - 5 mph (km/h) = maintained press.
If storing speeds is available and activated on your vehicle, theprogrammed speed will stop at the closest stored speed; refer to thecorresponding section.)Stop the cruise control system by pressing button 4: this isconfirmed in the screen (Pause).
)Switch on the cruise control again with another press on button 4 .
Exceeding the programmed speed
Intentional or unintentional exceeding of the programmed speed results in
flashing of this speed in the screen.
Return to the programmed speed, by means of intentional or unintentional
deceleration of the vehicle, automatically cancels the flashing of the speed.
Exiting cruise control mode
)Turn dial 1
to the "0"
position: the cruise control mode is deselected.
It disappears from the screen.



Operating fault

In the event of a cruise control malfunction,
the speed is cleared resulting in flashing of the dashes.
Have it checked by a CITROËN dealer or a
qualified workshop.

When the cruise control is switched on, be careful if you maintain the pressure on one of the programmed speed changingbuttons: this may result in a very rapidchange in the speed of your vehicle. Do not use the cruise control on slippery roads or in heavy traffic. On a steep descent, the cruise control will not be able to prevent the vehicle from exceeding the programmed speed. On steep climbs or when towing, the programmed speed may not be reached or maintained. To avoid any risk of jamming of the pedals:- ensure that the mat is positionedcorrectly,- never fit one mat on top of another.

Changing dipped beam headlamp
bulbs (only on models with
halogen headlamps)
)Remove the protective cover by pulling on
the tab. )Disconnect the bulb connector. )Spread the springs to release the bulb.)Extract the bulb and change it.
To reassemble, carry out these operations in
r
everse order.
Changing direction indicator
bulbs
When refitting, close the protectivecover carefully to preser ve the sealing
of the headlamp.


Amber coloured bulbs, such as thedirection indicators, must be replacedwith bulbs of identical specificationsand colour.

Rapid flashing of the direction indicator warning lamp (right or left) indicates thefailure of a bulb on that side.
Model with Xenon headlamps)
Remove the protective cover by pulling on
its tongue. ) Disconnect the electrical connector. )
Separate the springs to release the bulb.)
Pull the bulb out and replace it.
To r e a s s e m b l e , c a r ry out these operations in reverse order.Model with halogen headlamps)Turn the bulb holder a quarter of a turn and extract it. )Pull out the bulb and change it.
To reassemble, carry out these operations inreverse order.

Energy economy mode System which manages the period of use of cer tain functions to conser ve a sufficient level of charge in the battery.
After the engine has stopped, you can still use functions such as the audio equipment, windscreen
wipers, dipped beam headlamps, courtesy lamps, etc. for a maximum combined period of
thirty minutes.
This period may be greatly reduced if the battery is not fully charged.
A flat battery prevents the engine from
starting (refer to the corresponding paragraph).
If the telephone is being used at the same time on the navigation system, it will be interrupted after 10 minutes.


Switching to economy mode

Once this period has elapsed, a message
appears in the screen indicating that the vehiclehas switched to economy mode and the activefunctions are put on standby.

Exiting economy mode

These functions are reactivated automaticallythe next time the vehicle is driven. )In order to resume the use of these functions immediately, star t the engine and
let it run for a few minutes.
The time available to you will then be double
the period for which the engine is left running. However, this period will always be between
five and thir ty minutes.








Load reduction mode System which manages the use of certainfunctions according to the level of chargeremaining in the battery.
When the vehicle is being driven, the load
reduction function temporarily deactivates cer tain functions, such as the air conditioning,
th
e heated rear screen...
The deactivated functions are reactivated automatically as soon as conditions permit.

285
Technical data
WEIGHTS AND TOWED LOADS (in kg)
Petrol enginesVTi 120THP 155THP 160THP 200
GearboxesManualElectronic gearbox systemAutomaticManual
Model codes: NX...5FS05FV8/P5FMA5FU8


- Unladen wei
ght 1 2051 284 1 363
1 316



- Kerb weight 1 280
1 359
1 438
1 391



- Gross vehicle weight (GVW)
1 755

1 795

1 835

1 820



-
Gross train weight (GTW)
on a 12 % gradient
2 955
3 195

2 635

2 820



- Braked trailer
(within the GTW limit)
on a 12 % gradient 1 200
1 400
8001 000



- Braked trailer * (with load transfer within the
GTW limit) 1 4501 650 1 0001 250



- Unbraked trailer 640
680

715695



- Recommended nose weight
75

75
7575


*
The weight of the braked trailer can be increased, within the GTW limit, if the GV W of the towing vehicle is reduced by an equal amount. Warning:
towing using a lightly loaded towing vehicle may have an adverse effect on its road holding.
The
GTW and towed load values indicated are valid up to a maximum altitude of 1 000 metres; the towed load mentioned must be reduced by 10 % for each additional 1 000 metres of altitude.
The speed of a towing vehicle must not exceed 60 mph (10 0 km/h) (comply with the legislation in force in your country).
High ambient temperatures may result in a reduction in the performance of the vehicle to protect the engine; if the ambient temperature is above 37 °C,
limit the towed load.

Technical data
WEIGHTS AND TOWED LOADS (in kg)
Diesel enginesHDi 90 PEFHDi 110 PEFe-HDi 110 PEFHDi 160 PEF
GearboxManualManualManualElectronic gearbox systemManual
Model codes:NX...9HP09HR89HR8/S9HR8/PSRHH8


- Unladen wei
ght 1 205 1 2901 295 1 3001 320



- Kerb weight 1 280 1 365
1 370 1 375
1 395


-
Gross vehicle weight (GVW)

1 765

1 805

1 8101 815
1 880



-
Gross train weight (GTW)
on a 12 % gradient
2 865
3 105
3 110
3 115
3 180



- Braked trailer
(within GTW limit) on 12 % gradient
1 100
1 300
1 300
1 300 1 300


- Braked trailer
*
(with load transfer with the
GTW limit)
1 3501 550
1 550
1 550
1 550



-
Unbraked trailer 640
680
680680695



- Recommended nose weight 75 75 75 75 75

*

The wei
ght of the braked trailer can be increased, within the GTW limit, if the GV W of the towing vehicle is reduced by an equal amount. Warning:
towing using a lightly loaded towing vehicle may have an adverse effect on its road holding.
The
GTW and towed load values indicated are valid up to a maximum altitude of 1 000 metres; the towed load mentioned must be reduced by 10 % for each additional 1 000 metres of altitude.
The speed of a towing vehicle must not exceed 60 mph (10 0 km/h) (comply with the legislation in force in your country).
High ambient temperatures may result in a reduction in the performance of the vehicle to protect the engine; if the ambient temperature is above 37 °C,
limit the towed load.