2011.5 Citroen DS4 RHD turn signal

Warning lampis onCauseAction/Observations
Left-hand
direction indicator

flashing with buzzer. The lighting stalk is pushed down.
Right-handdirection indicator

flashing with buzzer. The lighting stalk is pushed up.



Sidelamps
fixed. The lighting control is in the"Sidelamps" position.
On vehicle where the daytime running lamps are deactivated,
if the lighting control is in the "AUTO" position, the sidelampscome on as a luminous signature of the vehicle.


Dipped beam headlamps
fixed. The lighting stalk is in the "Dipped beam
headlamps" position or in the "AUTO"
position in conditions of low li
ght.



Main beamheadlamps

fixed. The lighting stalk is pulled towards you. Pull the stalk again to return to dipped beam
headlamps.
Front foglamps
fixed. The front foglamps are switched on. Turn the ring on the stalk rear wards twice to switch off
the front foglamps.
Rear foglamps fixed. The rear foglamps are switched on. Turn the ring on the stalk rear wards to switch off the rear foglamps.
Hazard warninglamps flashing with audible
signal. The hazard warning lamps switch, located on the dashboard, has beenoperated. The le
ft-hand and right-hand direction indicators and
their associated indicator lamps flash simultaneously.
Operation indicator lamps
If one of the following indicator lamps comes on, this confirms that the corresponding system has come into operation.
It may be accompanied by an audible signal and a message on the multifunction screen.

105
Access
Starting the vehicle
)Inser t the key in the ignition switch.
The system recognises the star ting code. )Turn the key fully towards the dashboard toposition 3 (Starting).)When the engine star ts, release the key.
) Immobilise the vehicle.)
Turn the key fully towards you to
position 1 (Stop).)
Remove the key from the ignition switch.
Switching the vehicle off

A heavy object (key fob...), attached to the key and weighing down on its shaft in the ignition switch, could cause amalfunction.
Key left in the "Ignition on"position
On opening the driver's door, an aler t message is displayed, accompaniedby an audible signal, to remind you that the key is still in the ignition switch atposition 1 (Stop).
If the key has been left in the ignitionswitch at position 2 (Ignition on),the ignition will be switched off automatically after one hour. To switch the ignition back on, turn the key to position 1 (Stop)
, then back toposition 2 (Ignition on).

control, you can no longer unlock, lock or
locate your vehicle. )First of all, use the key in the lock to unlock
or lock your vehicle. )Then, reinitialise the remote control.
Fault with the remote
control
Reinitialisation
)Switch off the ignition and remove the ignition key.)Press the closed padlock immediately for a
few seconds.)Turn the key to position 2 (Ignition on).)Switch off the ignition and remove the keyfrom the ignition switch.
The remote control is fully operational again.

Changing the battery

Battery ref.: CR2032/3 volts.
)Unclip the cover using a small screwdriver at the two cutouts.)Lift off the cover. )Remove the flat battery from its location. )Fit the new battery into its location
observing the original direction of fitment. )Clip the cover onto the casing.
If the batter
y is flat, you are
informed by illumination of this
warning lamp, an audible signal
and a message in the screen.

If the problem persists, contact aCITROËN dealer as soon as possible.

127Visibility

Switching off the lighting when switching off the ignition

When the ignition is switched off, allof the lamps switch off immediately, except for the dipped beam headlamps if automatic guide-me-home lighting is activated.
Temporarily keeping the dipped beamheadlamps on after the vehicle's ignition has been switched off makes the driver's exit easier when the light is poor.
Switching on
)
With the ignition off, "flash" the headlamps using the lighting stalk.)
A further "headlamp flash" switches thefunction off.

Switching off
The manual guide-me-home lighting switches
o
ff automatically after a set time.
Manual guide-me-home
lighting

Switching on the lightingwhen switching on the ignition
To reactivate the lighting control stalk, turnthe ring Ato position A"0"
- lighting off, then to the position of your choice.
If the lighting is switched on manually after switching off the ignition, there is an audible signal when a front door is opened to warn the driver that they have forgotten to switchoff the vehicle's lighting, with the ignition off.
They switch off automatically after a periodwhich depends on the state of charge of thebattery (entry to energy economy mode).
Parking lamps
Side markers for the vehicle by illumination of
the sidelamps on the traffic side only.) Within one minute of switching off the
ignition, operate the lighting control stalk up
or down dependin
g on the traffic side(for example: when parking on the left;
lighting control stalk upwards; the right hand sidelamps are on).
This is confirmed by an audible signal and
illumination of the corresponding direction
indicator warning lamp in the instrument panel.
To switch o
ff the parking lamps, return the
lighting control stalk to the central position.

When a low level of ambient light is detected by a sunshine sensor, the number plate
lamps, sidelamps and dipped beam headlamps are switched on automatically, without any action on the par t of the driver. They can also come on if rain is detected, at the same time as automatic operation of the windscreen wipers.
As soon as the brightness returns to a sufficient level or after the windscreen wipers are switched off, the lamps are switched off automatically.
Automatic illumination of
headlam
ps
Activation
)
Turn the ring to the "AUTO"
position. The
activation of the function is accompanied
by the display of a message in the screen.


Deactivation
)
Turn the ring to another position.
Deactivation of the function isaccompanied by the display of a message
in the screen.
Automatic "guide-me-
home" li
ghting

Operating fault
In the event of a malfunction of
the sunshine sensor, the lighting comes on, this warning lamp is
displayed in the instrument panel and/or a
message appears in the screen, accompanied by an audible signal.
Contact a CITROËN dealer or a qualified
workshop.
In fog or snow, the sunshine sensor may detect sufficient light. In thiscase, the lighting will not come on automatically.
Do not cover the sunshine sensor,coupled with the rain sensor and located in the centre of the windscreen
behind the rear view mirror; theassociated functions would no longer be controlled.
When the automatic illumination of headlamps
function is activated, under low ambient
li
ght the dipped beams headlamps come on
automatically when the ignition is switched off.

Programming
Activation or deactivation, as well
as the duration of the guide-me-home lighting, is set in the vehicle configuration menu.

193Driving
With the ignition on or the engine running, torelease the parking brake, press on the brakepedalor the accelerator, pull then release
control A
.
Manual release


Before leaving the vehicle, ensurethat parking brake warning lamp inthe instrument panel is on fixed, not flashing.


Manual application
With the vehicle stationary, to apply the parkingbrake whether the engine is running or off, pullcontrol lever A.

The application of the parking brake is confirmed by:
- illumination o
f the braking warninglamp and of the P
warning lamp in
the control lever A,
- displa
y of the message"Handbrake on".
When the driver
’s door is opened with the engine running, a message is displayed
accompanied by an audible signal if the parkingbrake has not been applied, except in the case
of an automatic gearbox with the gear lever in position P.P
The full application of the parking brake is confirmed by:


- the brakin
g warning lamp and
the P warning lamp in the controllever Agoing off,

- displa
y of the message
"Handbrake off".
I
f you pull control lever A
without
pressing the brake pedal, the parkingbrake will not be released and awarning lamp will come on in the
instrument panel.


Maximum application

If necessary, you can make a maximum application
of the parking brake. This is obtained by means of a long pullon the control
l
ever A, until you see the message "Handbrake on maximum" and a beep is heard.
Maximum application is essential:

- in the case of a vehicle towing a caravan
or a trailer, if the automatic functions are
activated but you are applying the parkingbrake manually,

- when the gradient you are parked on may
vary (e.g. on a ferry, on a lorry, duringtowing).

In the case of towing, a loaded vehicle or parking on a gradient, make amaximum application of the parkingbrake then turn the front wheelstowards the pavement and engage agear when you park.
After a maximum application, the release time will be longer.

)With your foot on the brake, selectposition P
or N
. )Star t the engine.
If this procedure is not followed, there is an
audible signal, accompanied by a message in
the multifunction screen.)With the engine running, press the brakepedal. )Release the parking brake, unless it is programmed to automatic mode.)Select position R, D
or M,)Gradually release the brake pedal.
The vehicle moves off immediately.

If position N
is engaged inadver tentlywhile driving, allow the engine toreturn to idle then engage position D
toaccelerate.
When the engine is running at idle, withthe brakes released, if position R, Dor Mis selected, the vehicle moves even without the accelerator being pressed. When the engine is running, never leave children in the vehicle withoutsupervision. When carrying out maintenance withthe engine running, apply the parking brake and select position P.P


Automatic operation
)Select position D
for automatic
changing
of the six gears.
The gearbox then operates in auto-adaptive mode, without any inter vention on the par t
of the driver. It continuously selects themost suitable gear according to the style of
driving, the profile of the road and the load in
the vehicle.
For maximum acceleration without touching
the lever, press the accelerator pedal down fully (kick down). The gearbox changes down
automatically or maintains the gear selected
until the maximum engine speed is reached.
On braking, the gearbox changes down
automatically to provide efficient enginebraking.
If you release the accelerator sharply, the
gearbox will not change to a higher gear for safety reasons.

Never select position Nwhile thevehicle is moving. Never select positions Por R
unless the vehicle is completely stationary.

Invalid value during manualoperation
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).

Stopping the vehicle
Before switching off the engine, you canengage position Por N
to place the gearbox in neutral.
In both cases, apply the parking brake toimmobilise the vehicle, unless it is programmedto automatic mode.

If the lever is not in position P, when thePdriver's door is opened or approximately45 seconds after the ignition is switched off, there is an audible signal and amessage appears.)Return the lever to position P
; the audible signal stops and themessage disappears.


Operating fault

When the ignition is on, the lighting of this
warning lamp, accompanied by an audible
signal and a message in the multifunction
screen, indicates a gearbox malfunction.
In this case, the gearbox switches to back-up
mode and is locked in 3rd
gear. You may feel
a substantial knock when changing from Pto R
and from N
to R
. This will not cause any
damage to the gearbox.
Do not exceed 60 mph (10 0 km/h), local speed restrictions permitting.
Have it checked by a CITROËN dealer or aqualified workshop.
This warning lamp may also come on if a door
is opened.
You risk damaging the gearbox:


- if you press the accelerator and brake pedals at the same time,

- if you force the lever from position Pto another position when the batteryis flat.

To reduce fuel consumption when stationary for long periods with the engine running (traffic jam...), positionthe gear lever at Nand apply theparking brake, unless it is programmed in automatic mode.