2011.5 Citroen C4 AIRCROSS RHD ignition

176
Practical information
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not block traffic: if possible, park the vehicle on level, stable and non-slippery ground.
Apply the parking brake, switch off theignition and engage first gear to lock the wheels.If necessary, place a chock under the wheel diagonally opposite the wheel tobe changed. Never go underneath a vehicle raisedusing a jack; use a stand.


List of operations
)If your vehicle is equipped with security
wheel bolts (equipment available as an accessory) fit the security socket 5on the
wheelbrace 1to slacken the security bolt. )Slacken the other bolts using the
wheelbrace 1only.

194
Practical information

The batteries contain harmful substancessuch as sulphuric acid and lead. Theymust be disposed of in accordancewith regulations and must not, in any circumstances, be discarded withhousehold waste. Ta k e used remote control batteries andvehicle batteries to a special collection point.
Do not reverse the polarity and use only a 12 V charger. Do not disconnect the terminals while the engine is running. Do not charge the batteries without disconnecting the terminals first.Do not push the vehicle to star t the engine if it is fitted with a CVT gearbox.

It is advisable to disconnect the battery if the vehicle is to be left unused for more than one month.
Before disconnectingthe battery
Wait 2 minutes after switching off theignition before disconnecting the battery. Close the windows and the doors before disconnecting the battery.
Following reconnection of the battery
Following reconnection of the battery, switch on the ignition and wait 1 minutebefore starting to permit initialisation of theelectronic systems. However, if problemsremain following this operation, contact a CITROËN dealer or a qualified workshop.

)Disconnect the battery from the vehicle, if necessary. )Follow the instructions for use provided by
the manufacturer of the charger.
)Reconnect starting with the negative
terminal (-). )Check that the terminals and connectors are clean. If they are covered with sulphate (whitish or greenish deposit), remove themand clean them.
Charging the battery using
a battery charger

195
7
Practical information

Removing a front or rear
wiper blade
) Raise the corresponding wiper arm.)
Remove the wiper blade, sliding it towards
the outside.










Changing a wiper
blade

Fitting a front or rear wiper
blade
) At the front, check the size of the wiper blade as the shorter blade is fitted on the
right-hand side of the vehicle.) Put the corresponding new wiper blade in
place and fix it. )
Fold down the wiper arm carefully.


Automatic power cut-off to accessories

After the engine has stopped, when the ignition switch is in the "ACC" position(or the vehicle in "ACC" mode)
you can still use functions such as the audio equipment, windscreen wipers, dipped beamheadlamps, cour tesy lamps, etc. for about
t
hirty minutes.
Cutting off
Once the thir ty minutes have expired, thepower supply to the accessories will be automatically cut off.
Restoring power
The power supply will be restored the next time
the ignition is switched on.

The period before cut-off can beextended up to about sixty minutes or deactivated, via the colour screen"Equipment" menu.

196
Practical information





Recovering the vehicle



General
recommendations

Obser ve the legislation in force in your country.
Ensure that the weight of the towing vehicle is higher than that of the towed vehicle.
The person at the wheel of the towed vehicle must have a valid drivinglicence.
When towing a vehicle with all four wheels on the ground, always use anapproved towing bar; rope and strapsare prohibited.
When towing a vehicle with the engine off, there is no longer any power assistance for braking or steering.
In the following cases, you must always call on a professional recovery service:


- vehicle broken down on a motor way or fast road,

- 4 wheel drive vehicle,

- when it is not possible to put thegearbox into neutral, unlock the steering, or release the parking brake,

- towing with only two wheels on the ground,

- where there is no approved towing bar available...
Towing with the wheels on the groundis only possible on 2 wheel drive (2WD) versions.


Recovery of your vehicle


2 wheel drive (2WD) versions: towingwith the wheels on the ground
)Put the gear lever into neutral (position Nfor the CVT gearbox).)Unlock the steering by by turning the
ignition switch to the " ON
" position (or
t
o " ON " mode for vehicle fitted with the
"Keyless Entry and Star ting" system). )Release the parking brake. )Switch on the hazard warning lamps on both vehicles.)Move off gently and travel slowly for a shor t
distance only.
) Fit the towing bar to the towing eye on thechassis, located under the front bumper.

211
8
Checks






Checking levels


Take care when working under the bonnet, as certain areas of the engine may be extremelyhot (risk of burns).

Oil level
The check is carried out with the dipstick.
This check will only be correct if the
vehicle is on level ground and theengine has been off for more than 30 minutes.
It is normal to top up the oil level between
two ser vices
(or oil changes). CITROËN
recommends that you check the level, and top
up if necessary, every 3 000 miles (5 000 km).
After topping up the oil, the check when switching on the ignition with the oil levelindicator in the instrument panel is not validduring the 30 minutes after topping up.
Engine oil change
Refer to the ser vicing booklet for details of theinterval for this operation.
In order to maintain the reliability of the engine and emission control system, the use of additives in the engine oil is prohibited.
Oil specifi cation
The oil must be the correct grade for your
engine and conform to the manufacturer'srecommendations.

If a level drops si
gnificantly, have the corresponding system checked by a CITROËN dealer or a qualified workshop.
Check all of these levels regularly, in line with the ser vicing booklet and the requirements of the warranty. Top them up if necessary, unless other wise indicated.
Dipstick

There are two marks on the dipstick:
A
= m
aximum
If you fill past this mark,contact a CITROËN dealer or a qualified workshop. B
= minimum
Never allow the level to fallbelow this mark.

264
07
1
2
USB PLAYER





















USING THE USB PORT


With the vehicle stationary, ignition switch in the LOCK
position, connect a suitable cable to the portable player.
The USB port is used to connect a portable device
(MP3 player,Apple ®
player, ...). The fi les are sent from the player to your audio ®
system and heard through the vehicle's speakers.

Th
en connect the cable to the vehicle's
USB port. Models supported:
- iP
od touch® : FW version 1.1.1 or later. ®
- iPod classic ®: FW version 1.0 or later.
- iPod
5th generation ®: FW version 1.2.2 or later.
-
iPod nano 5th generation®
: FW version 1.2 or later. ®
- iPod nano 2 nd generation ®: FW version 1.1.2 or later.
-
Compatible USB mass storage device: 256 Mb capacity or greater.
File
formats: MP3, WMA, AAC, WAV.
Maximum number of levels (including root): 8.
Number of folders: 700.
Number of fi les: 65 535.
Do not connect the portable device directly to the U
SB port, use a cable.
To disconnect the cable, the i
gnition switch must be in the LOCKposition.
Navigation in the fi le base is done via the portable device / iPod®.
Take care not to trap the cable when closing the armrest.

276
10
09
9
11
12
13
14
15
16
17
Consult your mobile telephone's user manual and enter
the matching code recorded in step 7 in the telephone.
BLUETOOTH® TELEPHONE®
The system says " Start the matching procedure on the
telephone. Consult the instructions in the telephone manual ".
If the code is incorrect, the s
ystem locks. To clear the code:
- check that the telephone's voice reco
gnition is not activated,
- w
ith the ignition on and the audio system active, press the
END CALL button for 2 seconds, 3 times in succession.

Wh
en it detects a Bluetooth ®compatible mobile telephone,
the system says " Please say the name of the telephone after
the beep".

After the audible signal, allocate a name to the telephone
by saying the name of your choice.The s
ystem says "Allocate an order of priority between 1 and 7.
One is the highest level of priority ".
Give a number between 1 and 7 to establish the level of
priority of the mobile telephone.
The system says and con
fi rms the " name of the telephone" andthe " number
" of its priority. r


Answer "Ye s"
Say " No" to return to step 13.
The systems says " Matching complete " then emits an audible signal and deactivates the voice recognition. The services available depend on the network, the
SIM card and the compatibility of the Bluetooth ®telephone used. Check in your telephone user
manual and with your service provider for the services you have access to.
I
f the system does not detect the Bluetooth® compatible mobile®
telephone, the matching process stops ands is accompanied by an audible signal.
If
you select a level of priority which has already been allocated toanother telephone, the system asks you if you wish to replace this
level of priority.

287
1
1
1
11
03GENERAL OPERATION

Press the "PWR" button.
Th
e last source selected beforeswitching off resumes operation.
The audio equipment functions can be
used when the ignition switch is in the "ON" or "ACC" position.
To switch o
ff, press the "PWR" button
again.

ADJU
STING THE VOLUME

SETTING THE AUDIO MODES

Press the "
SOUND" button several
times; the audio modes change in the following order:

SUB PUNCH / TYPE / FIELD /
BASS / MID / TREBLE / FADER /
BALANCE / OFF.
Turn the "V
OL" dial respectively to the
left to decrease the volume or to theright to increase it. To access the personalised sound
functions quickl
y, press and hold
this button, then turn it to reach the
personalised sound setting of your choice.
Release the button to store thesetting. QUICK ACCESS MODE SWITCHING ON / OFF

The audio settin
g mode is deactivated when the radio is operated or a CD is played or after approximately 10 seconds without anyaction.I
f you press this button for more than2 seconds in the audio setting mode,
the system switches to "Hold" mode.
The audio mode selected will be
retained until you press this button again for more than 2 seconds. "HOLD" MODE