PERIODIC MAINTENANCE AND ADJUSTMENT
6-14
6
EAU20016
Final gear oil The final gear case must be checked
for oil leakage before each ride. If any
leakage is found, have a Yamaha deal-
er check and repair the vehicle. In addi-
tion, the final gear oil level must be
checked and the oil changed as follows
at the intervals specified in the periodic
maintenance and lubrication chart.
WARNING
EWA10370
Make sure that no foreign mate-
rial enters the final gear case.
Make sure that no oil gets on the
tire or wheel.
To check the final gear oil level1. Place the vehicle on the center- stand.TIPMake sure that the vehicle is positioned
straight up when checking the oil level.
A slight tilt to the side can result in a
false reading.2. Remove the final gear oil filler boltand its gasket, and then check the
oil level in the final gear case.
TIPThe oil level should be at the brim of the
filler hole.3. If the oil is below the brim of the fill-er hole, add sufficient oil of the rec-
ommended type to raise it to the
correct level.
4. Check the gasket for damage, and replace it if necessary.
5. Install the final gear oil filler bolt and its gasket, and then tighten the
bolt to the specified torque. To change the final gear oil
1. Place the vehicle on a level sur- face.
2. Place an oil pan under the final gear case to collect the used oil.
3. Remove the final gear oil filler bolt, the final gear oil drain bolt and their
gasket to drain the oil from the final
gear case.
4. Install the final gear oil drain bolt and its new gasket, and then tight-
en the bolt to the specified torque.1. Final gear oil filler bolt
2. Gasket
3. Correct oil level
1
2
3
Tightening torque: Final gear oil filler bolt:
23 Nm (2.3 m ·kgf, 17 ft· lbf)1. Final gear oil filler bolt
2. Final gear oil drain bolt
3. Gasket
231
U23PE0E0.book Page 14 Wednesday, March 3, 2010 2:29 PM
SPECIFICATIONS
8-2
8
Secondary reduction system:Shaft drive
Secondary reduction ratio: 21/25 × 32/9 (2.987)
Transmission type:
Constant mesh 6-speed
Operation: Left foot operation
Gear ratio: 1st: 36/13 (2.769)
2nd: 33/16 (2.063)
3rd:
33/21 (1.571)
4th: 30/24 (1.250)
5th: 25/24 (1.042)
6th:
26/28 (0.929)Chassis:Frame type:Steel tube backbone
Caster angle:
28.00 °
Trail: 126.0 mm (4.96 in)Front tire:Type:
Tubeless
Size: 110/80R19M/C 59V Manufacturer/model:
BRIDGESTONE/BW501
Manufacturer/model: METZELER/TOURANCE EXP C
Rear tire:Type:Tubeless
Size: 150/70R17M/C 69V
Manufacturer/model:
BRIDGESTONE/BW502
Manufacturer/model: METZELER/TOURANCE EXP CLoading:Maximum load:
209 kg (461 lb)
(Total weight of rider, passenger, cargo and
accessories)Tire air pressure (measured on cold
tires):Loading condition:0– 90 kg (0– 198 lb)
Front: 225 kPa (2.25 kgf/cm ², 33 psi)
Rear:
250 kPa (2.50 kgf/cm ², 36 psi)
Loading condition: 90–209 kg (198 –461 lb)
Front: 225 kPa (2.25 kgf/cm ², 33 psi)
Rear:
290 kPa (2.90 kgf/cm ², 42 psi)
Front wheel:Wheel type:
Spoke wheel
Rim size:
19M/C x MT2.50Rear wheel:Wheel type:Spoke wheel
Rim size:
17M/C x MT4.00Front brake:Type:Dual disc brake
Operation:
Right hand operation
Recommended fluid: DOT 4Rear brake:Type:
Single disc brake
Operation: Right foot operation
Recommended fluid: DOT 4Front suspension:Type:Telescopic fork
Spring/shock absorber type: Coil spring/oil damper
Wheel travel:
190.0 mm (7.48 in)Rear suspension:Type:Swingarm (link suspension)
U23PE0E0.book Page 2 Wednesday, March 3, 2010 2:29 PM
