2010 YAMAHA RHINO 700 oil

8-25 1. Oil filler hole access panel
1. Cache d’accès à l’orifice de remplissage d’huile
1. Panel de acceso a la boca de llenado de aceite
1
5B410012
Engine oil and oil filter cartridge
Check engine oil level before each operation. In
addition, change the oil and the oil filter cartridge at
the intervals specified in the periodic maintenance
and lubrication chart.
To check the engine oil level
1. Park the vehicle on a level surface.
2. Remove the oil filler hole access panel by
pulling it outward.
3. Check the engine oil level on a cold engine. If
the engine was started before checking the
oil level, be sure to warm up the engine suffi-
ciently, and then wait at least ten minutes un-
til the oil settles for an accurate reading.
EE.book Page 25 Monday, January 19, 2009 5:30 PM

8-27 1. Engine oil dipstick
1. Jauge d’huile moteur
1. Varilla de medición del aceite del motor
1
1. Engine oil dipstick 2. Maximum level mark
3. Minimum level mark
1. Jauge d’huile moteur 2. Repère de niveau maximum
3. Repère de niveau minimum
1. Varilla de medición del aceite del motor
2. Marca de nivel máximo 3. Marca de nivel mínimo
2
3
1
4. Remove the engine oil dipstick, and then
wipe it off with a clean rag.
5. Insert the dipstick completely into the oil filler
hole with the arrow mark on the dipstick knob
pointing upward as shown, and then remove
it again to check the oil level. The engine oil
should be between the minimum and maxi-
mum level marks.
6. If the engine oil is at or below the minimum
level mark, add sufficient oil of the recom-
mended type to raise it to the correct level.
7. Insert the dipstick completely into the oil filler
hole with the arrow mark on the dipstick knob
pointing upward.
EE.book Page 27 Monday, January 19, 2009 5:30 PM

8-29 1. Oil filler hole access panel
1. Cache d’accès à l’orifice de remplissage d’huile
1. Panel de acceso a la boca de llenado de aceite
1
1. Engine guard 2. Bolt (× 10)
1. Protège-carter 2. Vis (× 10)
1. Protector del motor 2. Perno (× 10)
1
22
2
8. Install the oil filler hole access panel in the
original position.
To change the engine oil (with or without oil fil-
ter cartridge replacement)
1. Park the vehicle on a level surface.
2. Remove the engine guard by removing the
bolts.
3. Remove the oil filler hole access panel by
pulling it outward.
4. Start the engine, warm it up for several min-
utes, and then turn it off.
EE.book Page 29 Monday, January 19, 2009 5:30 PM

8-31 1. Engine oil drain bolt
1. Vis de vidange d’huile moteur
1. Tornillo de vaciado del aceite del motor
1
1. Oil filter cartridge 2. Oil filter wrench
1. Cartouche du filtre à huile 2. Clé pour filtre à huile
1. Cartucho del filtro de aceite 2. Llave del filtro de aceite
21
5. Place an oil pan under the engine to collect
the used oil, and then remove the dipstick.
6. Remove the engine oil drain bolt to drain the
oil from the crankcase.
Skip steps 7–9 if the oil filter cartridge is not being
replaced.
7. Remove the oil filter cartridge with an oil filter
wrench. An oil filter wrench is available from a
Yamaha dealer. Make sure that the O-ring is
removed together with the oil filter cartridge.
If the O-ring remains attached to the crank-
case, oil leakage may occur.
EE.book Page 31 Monday, January 19, 2009 5:30 PM

8-33 1. O-ring
1. Joint torique
1. Junta tórica
1. Oil filter cartridge 2. Torque wrench
1. Cartouche du filtre à huile 2. Clé dynamométrique
1. Cartucho del filtro de aceite 2. Llave Dinamométrica
2 1
8. Apply a light coat of clean engine oil to the O-
ring of the new oil filter cartridge. Make sure
the O-ring is seated properly.
9. Install the new oil filter cartridge with an oil fil-
ter wrench, and then tighten it to the specified
torque with a torque wrench.
10. Reinstall the engine oil drain bolt, and then
tighten it to the specified torque. Tightening torque:
Oil filter cartridge:
17 Nm (1.7 m·kgf, 12 ft·lbf)
Tightening torque:
Engine oil drain bolt:
30 Nm (3.0 m·kgf, 22 ft·lbf)
EE.book Page 33 Monday, January 19, 2009 5:30 PM

8-35
11. Refill with the specified amount of recom-
mended engine oil, and then insert the dip-
stick completely into the oil filler hole with the
arrow mark on the dipstick knob pointing up-
ward. NOTICE: Be sure to wipe off spilled
oil on any parts after the engine and ex-
haust system have cooled down.
Recommended engine oil:
See page 10-3.
Oil quantity:
Without oil filter cartridge replacement:
2.00 L (2.11 US qt, 1.76 Imp.qt)
With oil filter cartridge replacement:
2.10 L (2.22 US qt, 1.85 Imp.qt)
EE.book Page 35 Monday, January 19, 2009 5:30 PM

8-37
NOTICE

In order to prevent clutch slippage (since
the engine oil also lubricates the clutch),
do not mix any chemical additives with oil.
Do not use oils with a diesel specification
of “CD” or oils of a higher quality than
specified. In addition, do not use oils la-
beled “ENERGY CONSERVING II” or high-
er.


Make sure that no foreign material enters
the crankcase.
12. Start the engine, and then let it idle for sever-
al minutes while checking it for oil leakage. If
oil is leaking, immediately turn the engine off
and check for the cause.
13. Turn the engine off, wait at least ten minutes,
and then check the oil level and correct it if
necessary.
14. Install the engine guard by installing the bolts,
and then tightening them to the specified
torque.
EE.book Page 37 Monday, January 19, 2009 5:30 PM

8-39
15. Install the oil filler hole access panel in the
original position. Tightening torque:
Engine guard bolt:
7 Nm (0.7 m·kgf, 5.1 ft·lbf)
EE.book Page 39 Monday, January 19, 2009 5:30 PM