2010 SUBARU FORESTER air condition

pAn e l il l Um i n At i o nWhen the headlight switch is in the or position, you can adjust
the brightness of the instrument panel
illumination for better visibility. To
brighten, turn the control dial upward. To
darken, turn the control dial downward.
Ho o d re l e As eTo open your hood, pull the hood release
lever located under the left side of the
instrument panel.
HeA d l i g Ht sDaytime running lights are standard on your
vehicle. To turn on parking lights or headlights,
twist the end of the turn signal lever forward.
To change headlights from low beam to high
beam, push the turn signal lever forward; to
return to low beam, pull the lever back. To
flash the headlights, pull the lever toward you
and then release it.
fo g li g Ht s (i f e q Ui p p e d)Your fog lights will only operate when your
headlights are on low beam. To turn the fog
lights on, turn the dial up. To turn the fog
lights off, turn the dial back down.
co o l An t te m p e r AtU r eIllumination in BLUE indicates insufficient
warming up of the engine. Illumination in RED
indicates overheating condition of the engine.
cH e c k en g i n e li g HtIf this light comes on and stays on, see
your Subaru dealer as soon as possible.
There may be a problem with your
emission control system. NOTE: If you
have recently fueled your vehicle, the
“CHECK ENGINE” light may stay on due
to a missing or loose fuel filler cap. (The
cap should be tightened until it clicks.)
lo w fUe l
w
A r n i n g li g Ht If this light appears, refuel promptly; your
tank is nearly empty. Approximately 2.6 U.S.
gallons of fuel remain.
ABs wAr n i n g li g HtIf the ABS (Anti-lock Brake System) light
comes on and stays on after the vehicle
speed exceeds approximately 8 mph,
the ABS system may not be working
properly. (The conventional brake system
will continue to operate normally.) Have
the ABS system checked by your Subaru
dealer at the first available opportunity.
crU i s e co n t r o lSET Push the “CRUISE” button located
on the steering wheel. The “CRUISE”
indicator light on the instrument panel
will turn on. Press the accelerator pedal
until your vehicle reaches the desired
speed. Push the “SET/COAST” button
and release. Ease off the accelerator pedal. Your vehicle will maintain the
desired speed.
TEMPORARY CANCEL There are four
ways to temporarily cancel cruise
control: depress the brake pedal; push
the “CANCEL” button; press the clutch
pedal (manual transmission); or, shift
the selector lever into the “N” position
(automatic transmission).
RESUME
Push the “RES/ACC” button with
the vehicle speed approximately 20 mph
or more.

SHUT OFF To quit cruise control,
push the main “CRUISE” button again,
or, when the vehicle is stopped, turn
the ignition switch to the “ACC” or
“LOCK” position.
INCREASE SPEED Push the
“RES/ACC” button, hold until your
vehicle reaches the desired speed, and
release. To increase speed using the
accelerator pedal, press the pedal until
you reach the desired speed. Push the
“SET/COAST” button to set the speed.
DECREASE SPEED Push and hold the
“SET/COAST” button, until your vehicle
slows to the desired speed, then release.
To decrease the speed using the brake
pedal, press the pedal to release cruise
control temporarily. When the speed
decreases to the desired rate, push the
“SET/COAST” button.
wi n d sHi e l d wi p e r sTo turn wipers on, press the wiper control
lever down one level for intermittent, two
levels for low, or three levels for high speed.
Return the lever to the “OFF” position to
stop wipers. For a single wipe/mist, pull
the lever toward you. To spray washer fluid
spray, press the washer button at the end
of the wiper control lever. To operate the
rear wiper, turn the knob on the end of
the control lever forward to intermittent,
continuous, or wash position. Turn the end
of the lever backward for wash operation
when the rear wiper is not in use.
pAs s e n g e r fr o n t Al Ai r B A g
on/off i
n d i c At o r sThese indicators, located next to the clock,
show the status of the front seat passenger’s
SRS frontal air bag. If the air bag is enabled,
the frontal air bag ON indicator light will
illuminate. If the air bag is disabled (not
activated to deploy in an accident), the OFF
indicator will illuminate. Please refer to your
Owner’s Manual for complete details.
HA zA r d wAr n i n g flA sH e r sPress the hazard button to turn flashers
on to warn other drivers when you are
experiencing emergency conditions.
Press again to turn flashers off.
10
2
1
3
4
7
8
9
5 11
12
6
Instrument panel
3
199382_10_Forester_QRG_042709.indd 44/27/09 4:08:49 PM

mAi n t Ai n co m f o r t i n An y co n d i t i o n For hot, cold and everything in between, Subaru
climate control systems allow you to maintain comfort in any condition. \
With the automatic climate control
system, the “AUTO” feature automatically controls air temperature,\
fan speed, and distribution of air flow at
the touch of a button.
8
1
2
3
4
5
6
7
199382_10_Forester_QRG_042709.indd 94/27/09 4:09:47 PM

AUtom Atic clim Ate
control (
i f e q Ui p p e d)When the climate control system is set to
AUTO, the outlet air temperature, fan speed,
air flow distribution, air inlet control and
air conditioner compressor operation are
all automatically controlled to maintain a
constant, comfortable temperature inside the
vehicle. The automatic climate control system
utilizes several delicate sensors. If damaged,
the system may not be able to control the
interior temperature correctly. Do not subject
the sensors to impact, keep water away from
them and do not cover them.
fAn sp e e d co n t r o l diA l Turn the dial to AUTO (recommended
setting) to automatically adjust the
fan speed in accordance with the air
temperature inside and outside the
vehicle. Turn the dial past AUTO to select
the desired fan speed. Turn the dial to
the OFF position to turn the fan off.
Ai r in l e t se l e c t i o n BU t t o n Select this function for fast cooling with
the air conditioner or when driving on
a dusty road. Press the button to turn
ON the air inlet and recirculate air
inside the vehicle. The indicator light
illuminates. When the interior has cooled
to a comfortable temperature or the
road is no longer dusty, press the button
again to turn OFF the air inlet and allow outside air to flow into the vehicle. Press
the button again to cancel the AUTO
mode. To prevent fogging, do not stay in
the recirculated mode for any extended
period of time. When both the air flow
control dial and the fan speed control
dial are in the AUTO position, the air
inlet is set to the AUTO mode. Operating
the air inlet selection button in this state
cancels the AUTO mode. To return to the
AUTO mode, turn the air flow control
dial or the fan speed control dial to a
position other than the AUTO position.
Then turn to the AUTO position.
Ai r fl o w co n t r o l di
A lThis dial has six positions. Subaru
recommends using the AUTO position,
which adjusts the air flow automatically
in accordance with the air temperature
inside and outside the vehicle. The
dial can also be set to distribute air
through the instrument panel outlets;
the instrument panel outlets and foot
outlets simultaneously; the foot outlets;
the windshield defroster outlets and foot
outlets simultaneously; or solely through
the windshield defroster outlets.
reA r wi n d o w
d
e f o g g e r BU t t o n Press the rear window defogger button
to clear the rear window of fog or frost.
The indicator light will illuminate while
activated. To turn the rear defogger off, press the button again. The rear
defogger will shut off automatically
after approximately 15 minutes. This
button also operates the outside
mirror defogger (if equipped) and the
windshield wiper de-icer (if equipped).
wi n d s
Hi e l d de f r o s t/de f o gTo clear the windshield and side windows
of fog or frost, set the air flow control to
the defrost position, turn the temperature
control dial fully clockwise and set the fan
speed control to the fastest speed. When
the dial is set to the windshield defrost or
simultaneous foot outlet and windshield
defrost position, the air conditioner
compressor operates automatically to
defog the windshield quickly. At the
same time, the air inlet selection is
automatically set to outside air mode.
te m p e r AtU r e co n t r o l diA l
This dial is used to set the desired interior
temperature. Turn the dial fully
counterclockwise for maximum cooling
performance. Turn fully clockwise for
maximum heating.
Ai r co n d i t i o n i n g BU t t o n When the fan speed control dial is
in a position other than OFF and the
A/C button is pushed, the cooling/
dehumidifying function will start
operating and the indicator light will
illuminate. To stop the function, push the A/C button again. When both the
air flow control dial and the fan speed
control dial are in the AUTO position,
the cooling/dehumidifying function is
set to the AUTO mode. Operating the
air conditioner button in this state
cancels the AUTO mode of the cooling/
dehumidifying function. To return to the
AUTO mode, turn the air flow control
dial or the fan speed control dial to a
position other than the AUTO position.
Then turn to the AUTO position.
13
2
Climate controls
7
5
4
6
9
199382_10_Forester_QRG_042709.indd 104/27/09 4:10:13 PM