2010 SKODA YETI Technical Change

Tyre repair kit*
8 Tyre inflator bottle with sealing agent
Replacement valve core
The valve remover has a slot at its lower end which fits into the valve core. This is
the only way in which you can remove and re-i nstall the valve core from the tyre valve.
The same also applies to the replacement valve core .
Preparing to use the tyre repair kitBefore using the tyre repair kit, carry out the following preparatory work:
– Park the vehicle as far away as possible from the traffic flow. Park on as flat and firm a surface as possible.
–Have all the occupants get out. While changing a wheel, the occupants of the
vehicle should not stand on the road (instead of behind a crash barrier).
– Switch off the engine and engage 1st gear or if your vehicle is fitted with an auto-
matic gearbox, position the selector lever into position P .
– Apply the handbrake firmly.
– Check whether you can carry out the repairs with the tyre repair kit page 6,
“General information”.
– If a trailer is coupled, uncouple it.
– Remove the tyre repair kit from the luggage compartment.
– Stick the sticker page 7, fig. 7 on the dash panel in view of the driver.
– Do not remove the foreign body, e.g. screw or nail, from the tyre.
– Unscrew the valve cap.
– Use the valve remover to remove the va lve core and place it down on a clean
surface.Seal and inflate tyresSealing tyres– Forcefully shake the tyre inflator bottle page 7, fig. 7 several times. – Firmly screw inflation hose onto the tyre inflator bottle in a clockwise direction
. The film on the cap is pierced automatically.
– Remove the plug from the inflation hose and plug the open end fully into the tyre valve.
– Hold the bottle with the floor facing upwards and fill the whole sealing agent in the tyre inflator bottle into the tyres.
– Remove the empty tyre inflator bottle from the valve.
– Screw the valve core back into the tyre valve using the valve remover .
Pumping up the tyres– Screw the tyre inflation hose page 7, fig. 7 of the air compressor firmly onto
the tyre valve.
– Check whether the air re lease valve is closed.
– Start the engine and run it in idle.
– Plug the cable connector into the 12 Vo lt socket in the vehicle, see Owner's
manual.
– Switch on the air compressor with the ON and OFF switch .
– Allow the air compressor to run until reac hing a pressure of 2.0 - 2.5 bars for a
maximum of 8 minutes !
– Switch off the air compressor with the ON and OFF switch.
– If you cannot reach an air pressure of 2.0 – 2.5 bar, unscrew the tyre inflation hose from the tyre valve.
– Drive the vehicle 10 metres forwards or backwards to allow the sealing agent to
distribute in the tyre.
– Screw the tyre inflation hose of the air compressor firmly back onto the tyre
valve and repeat the inflation procedure.
– If you cannot reach the required tyre inflation pressure here either, this means the tyre has sustained too much damage. You cannot seal with tyre with the break-
down kit .
– Switch off the air compressor with the ON and OFF switch.
– Remove the tyre inflation hose from the tyre valve.
A10A11
A1
A11
A2
A1
A10
A3
A10
A3
A10
A1
A5
A7
A9
A8
A5
A5
A5
s35k.9.book Page 8 Thursday, September 16, 2010 10:24 AM

Tow-starting and towing vehicle9
If you reached a tyre inflation pressure of 2.0 – 2.5 bar, resume driving at a maximum
speed of 80 km/h (50 mph).
Check the tyre inflation pressure after driving 10 minutes page 9, “Check after
driving for 10 minutes”.
WARNING
•
During inflation, the tyre inflation hose and air compressor may get hot-
risk of injury!
•
Do not place hot tyre inflation hoses or hot air compressors on flammable
materials - risk of fire!
•
If you cannot inflate the tyre to at least 2.0 bar, this means the damage
sustained was too serious. The sealing agent cannot be used to seal the tyre. Do
not drive the vehicle. Get professional assistance.Caution
Switch off the air compressor after running 8 minutes at the latest - danger of over-
heating! Allow the air compressor to cool a few moments before switching it on
again.Check after driving for 10 minutesCheck the tyre inflation pressu re after driving 10 minutes.If the tyre inflation pressure is 1.3 bar or less:–Do not drive the vehicle! You cannot properly seal wi th tyre with the breakdown
kit.
– Obtain professional assistance.If the tyre inflation pressure is 1.3 bar or more:– Adjust the tyre inflation pressure to the corr ect value (see inside of fuel filler cap).
– Continue driving carefully to the nearest specialist garage at a maximum speed of 80 km/h (50 mph).
Tow-starting and towing vehicleGeneral
Caution
Do not push or two the vehicle to start the engine - likely engine damage! In vehicles
with catalytic converters, fuel may get into the catalytic converter where it may ignite.
This results in the catalytic converter overheating and being destroyed. To help start
the engine, you can use a battery from another vehicle, see Owner's manual.Electric fusesFuse assignment in engine compartmentFuse assignment in the dash panelNo.
Power consumer
Amperes
F11
Control unit for auxiliary heating
30
No.
Power consumer
Amperes
36
DVD
5
s35k.9.book Page 9 Thursday, September 16, 2010 10:24 AM

Technical Data
10
Technical DataWeightThe indicated unloaded weight is for orient ation purposes only. It is for the basic
equipping of the vehicle not includin g special features or accessories.
Caution
Do not exceed the permissible overall weight of the vehicle - risk of accident and
damage to the vehicle. Max. permissible gross weight per axleMax. permissible gross weight per axle (in kg) - front/rear axlePetrol engines1.2 ltr./77 kW TSI (M6)
950/980
930/1110
a)
a)Vehicles of category N11.2 ltr./77 kW TSI (DQ7)
980/970
960/1110
a)
1.8 ltr./118 (112) kW TSI
1070/1030
1050/1160
a)
Diesel engines2.0 ltr./81 kW TDI CR DPF (M5)
1040/960
1020/1100
a)
a)Vehicles of category N12.0 ltr./81 kW TDI CR DPF (M6)
1090/1020
1070/1160
a)
2.0 ltr./103 kW TDI CR DPF (M6)
1090/1030
1070/1160
a)
2.0 ltr./103 kW TDI CR DPF (DQ6)
1120/1020
1100/1160
a)
2.0 ltr/125 kW TDI CR DPF
1090/1030
1070/1170
a)
s35k.9.book Page 10 Thursday, September 16, 2010 10:24 AM

Technical Data11
1.4 ltr./90 kW TSI - EU5Engine
Engine oil specifications
Performances
Fuel consumption (in ltr./100 km) and CO
2 emission (in g/km)
Power output
kW per rpm
90/5000
Maximum torque
Nm per rpm
200/1500-4000
Number of cylinders/Displacement (cm
3)
4/1390
Specification
Engine oil specifications for models with flexible service intervals (QG1)
VW 503 00, VW 504 00
Engine oil specifications for vehicles with fixed service intervals (QG2)
VW 501 01, VW 502 00
Maximum speed
km/h
185
Acceleration 0 - 100 km/h
s
10.5
Urban
8.9
Ex-urban
5.9
combined
6.8
CO2 emissions combined
159
s35k.9.book Page 11 Thursday, September 16, 2010 10:24 AM

Technical Data
12
Capacities (in liter)
Weight (in kg)
Angle (in degree)Engine oil
a)
a)Oil capacity with oil filter change. Inspec t oil level when filling; do not fill up too much. The oil level must be between the markings.
3.6
Cooling system of the vehicle
b)
b)On vehicles which are fitted with an independent auxiliary heating and ventilation, the volume of the coolant is greater by approx. 1 ltr.
7.7
Permissible gross weight
1920/1975
a)
a)Vehicles of the group N1.Unladen weight ready for operation
1375
Loading capacity
620/675
a)
Loading capacity when using the TLC
540
Max. permissible gross weight per front axle
1000/980
a)
Max. permissible gross weight per rear axle
960/1100
a)
Permissible trailer loads, trailer braked
1300
Permissible trailer loads, trailer unbraked
650
Slope angle (°)/climbing ability (%)
27/50
s35k.9.book Page 12 Thursday, September 16, 2010 10:24 AM

Technical Data13
1,6 l/77 kW TDI CR - EU5Engine
Engine oil specifications
Performances
Fuel consumption (in ltr./100 km) and CO
2 emission (in g/km)
Power output
kW per rpm
77/4400
Maximum torque
Nm per rpm
250/1500-2500
Number of cylinders/Displacement (cm
3)
4/1598
Specification
Engine oil specifications for models with flexible service intervals (QG1)
VW 507 00
Engine oil specifications for vehicles with fixed service intervals (QG2)
VW 507 00
Maximum speed
km/h
176
Acceleration 0 - 100 km/h
s
12.1
Urban
5.2
Ex-urban
4.2
combined
4.6
CO2 emissions combined
119
s35k.9.book Page 13 Thursday, September 16, 2010 10:24 AM

Technical Data
14
Capacities (in liter)
Weight (in kg)
Dimensions (mm)
Angle (in degree)Engine oil
a)
a)Oil capacity with oil filter change. Inspec t oil level when filling; do not fill up too much. The oil level must be between the markings.
4.3
Cooling system of the vehicle
b)
b)On vehicles which are fitted with an independent auxiliary heating and ventilation, the volume of the coolant is greater by approx. 1 ltr.
8.4
Permissible gross weight
1955/2010
a)
a)Vehicles of the group N1.Unladen weight ready for operation
1410
Loading capacity
620/675
a)
Loading capacity when using the TLC
540
Max. permissible gross weight per front axle
1040/1000
a)
Max. permissible gross weight per rear axle
960/1100
a)
Permissible trailer loads, trailer braked
1400
Permissible trailer loads, trailer unbraked
650
Clearance
155
Front embankment angle
17.1
Rear embankment angle
25.2
Ramp angle
17.2
Slope angle (°)/climbing ability (%)
29/55
s35k.9.book Page 14 Thursday, September 16, 2010 10:24 AM

s35k.9.book Page 15 Thursday, September 16, 2010 10:24 AM