Radio
6
Store station
– After selecting the radio station, hold one of the station keys , on
which it should be stored until it briefly switches to mute and a brief
signal sounds.
Automatic station finding with storing the radio stations
– Press the button . An automatic station finding is started during which the 6 stations with the strongest signal in the memory level
FM2, TP or AM2 are stored. STORE is displayed on the display.When storing the radio stations on the st ation keys is finished, you can call up
the desired radio station by pressing a station key .
Note
The stored radio stations are updated and stored once again by repetitively
pressing the button .Radio textCertain radio stations transmit addition al text information - designated as
radio text.
Note•
The text information must not be available to all radio stations.
•
Depending upon the quality of the received signal, the radio needs a specific
time, in order to correctly read all the illustrated characters.
RDS functionsRDS (“ Radio Data System”) serves to transmit program identification and additional
services therefore also enabling automatic tracking of stations. In the event of sufficiently satisfactory reception the suitable RDS radio stations will
display the station name instead of the station frequency.
If a radio station sends additional inform
ation via the RDS function while a station
is being stored, it can occur that the name of the radio station is later displayed
incorrectly in the memory list.
Tr a f f i c r e p o r t sActivating and deactivating the traffic reports
Press the button , TP appears in the display. If a set radio station does not
transmit a traffic report, the radio searches for a station which transmits the traffic
report. TP SEEK is displayed on the display.
If no radio station which transmits the traffic reports is found, NO TP is shown on
the display.
An incoming traffic report automatically inte rrupts the CD play function or listening
to a radio station, which at that moment is not transmitting a traffic report. INFO
PRGNAME is displayed on the display. At th e end of the traffic report, the radio
automatically returns to the original play function.
If you wish to deactivate the traffic information, press once again the button , TP
goes out on the display.Traffic information memory Automatic recording of traffic reports
If the traffic information function is switched on, a traffic information station
is received and the incoming traffic reports will be recorded as long as the ignition
is switched on. This way you are informed at any time of the current traffic situation,
even if you have your radio switched off for a lengthy period while driving.
If the vehicle is not in use (ignition off) while a traffic information station is received
and the traffic information function is sw itched on, incoming traffic reports from
this station are recorded for two hours.
When switching the ignition off the current traffic information station is displayed
for about five seconds, from which the ne xt two hours of traffic reports will be
A7
AS
A7A7
AS
TP
TP
AIM
s1tk.book Page 6 Thursday, March 20, 2008 1:56 PM
Radio7
recorded. During this display of five seco nds, you can select another traffic infor-
mation station using the arrow keys on the unit, which will be recorded.
If, when the vehicle is not in use, the reception of the set traffic information station
is too poor because of external influences , it will automatically search for another
traffic information station.
A maximum of nine traffic announcements with a total length of up to four minutes
can be recorded. The oldest traffic report will always be overwritten if the memory
is full.
Record for 2 hours
If the TP range was selected before switch ing off the radio, all the following traffic
reports are automatically recorded during th e next 2 hours. “TIM 2 H” is shown in
the display.
Record for 24 hours
A 24 hour recording mode is activated in the switched-off status by pressing the
button . The last heard program and “TIM 24 H” is shown in the display.
Note
•
The radio stations broadcasting this information are responsible for the content
of the traffic reports.
•
A recording of traffic reports is only poss ible, if the traffic information function
is switched on and a traffic information station is received (Display: TP).
•
The oldest traffic report will always be overwritten if the memory is full.
•
In case of a message of over four minut es long, the beginning is overwritten.
•
If you switch on the radio while recording a message, the recording is
interrupted.
Playing traffic reports– Press on the button , in order to listen to the stored traffic reports. The play function starts with the last recorded traffic report and runs
through to the oldest recorded traffic report. – If you press the rocker switch , you can return to the beginning of
the currently replayed traffic report.
– If you press the rocker switch twic e during the play function, you
can switch between the recorded messages by pressing the rocker
switch or .
– You must keep the rocker switch or pressed for a fast reverse or forwards replay of the announcements.
AIM
AIM
s1tk.book Page 7 Thursday, March 20, 2008 1:56 PM
