2010 Seat Alhambra display

Driving 206
Selector lever locking
The gear selector lever lock prevents, in P or N, a gear selection from being
inadvertently engaged and the vehicle moving off accidentally.
To release the gear selector lever lock, press and hold the brake pedal with
the ignition on. Press simultaneously on the selector lever lock.
The selector lever lock is not engaged if the selector lever is moved quickly
through position N (e.g. when shifting from R to D). This makes it possible, for
instance, to rock the vehicle backwards and forwards if it is stuck in snow or
mud. The selector lever lock engages automatically if the brake pedal is not
pressed and the lever is in position N for more than about one second at a
speed of less than 5 km/h (3 mph).
In vehicles with a DSG
® automatic gearbox, on rare occasions the selector
lever lock may not engage. In this case, the transmission is locked to prevent
the vehicle from moving accidentally. The green control light
K flashes and
an information text is displayed. Proceed as follows to engage the selector
lever lock:
xPress the brake pedal and then release.
WARNING
Placing the selector lever in an incorrect position may cause loss of control
of the vehicle and a serious accident.
xDo not press the accelerator when engaging a range of gears.
xWith the engine running and a range of gears selected, the vehicle will
move off when the brake pedal is released.
xNever select reverse gear or the parking lock while driving.
WARNING
Unintentional movements of the vehicle could cause serious injury.
xAs a driver, you should never leave your vehicle if the engine is running
and a gear is engaged. If you have to leave your vehicle while the engine is running, you must apply the electronic parking brake and engage parking
lock P.
xWhile the engine is running and with the D, S or R range of gears
selected, keep the brake pressed to keep the vehicle at a standstill. Trans-
mission is not totally interrupted either when the vehicle is idling or when
the vehicle continues moving forwards.
xNever engage the R or P gear ranges when the vehicle is moving.
xNever leave the vehicle with the gear selector in N. The vehicle may
move downhill regardless of whether the engine is switched on or not.
Caution
If, when the vehicle is at a standstill, the electronic parking brake is not
applied and the brake pedal is released while in position P, the vehicle may
move a few centimetres forwards or backwards.
Note
If, while driving, the selector lever is accidentally placed in position N, lift your
foot off the accelerator. Wait until the engine is running at idle speed before
selecting a new gear ratio.
WARNING (continued)

Driving 208
Driving down hills
The steeper the gradient, the lower the gear you will need. The lowest gears
increase the engine braking work. Never go down hills with the selector lever
in neutral N.
xYou should reduce speed accordingly.
xPress the selector lever from position D to the right into the Tiptronic
selector gate Ÿpage 207.
xGently pull the selector lever back to change down a gear.
xALTERNATIVELY: Reduce using the steering wheel paddles Ÿpage 207.
Emergency program
If all the selector lever positions on the instrument panel display are shown
with a light-coloured background, this means there is a fault in the system.
The automatic gearbox will operate in emergency programme mode. When
the emergency program is activated, it is possible to drive the vehicle
however, at low speeds and within a selected range of gears.
For the DSG
® dual clutch gearbox, in some cases, this may mean that reverse
gear does not engage. The gearbox should be checked by a qualified work-
shop as soon as possible.
Overload protection for the 6-speed DSG gearbox
®
When the clutch is overloaded, the vehicle begins to jerk and the selector
lever position indicator begins to flash. To prevent damage to the clutch, this
interrupts the power transmission between the engine and the gearbox.
There is no more traction and it is not possible to accelerate. If the clutch is
opened automatically due to overloading, press the brake pedal. Wait a few
seconds before starting to move again.
Kick-down
The kick-down system provides maximum acceleration when the gear
selector lever is in the positions D, S or in the Tiptronic position.When the accelerator pedal is pressed right down, the automatic gearbox will
shift down to a lower gear, depending on road speed and engine speed. This
takes advantage of the maximum acceleration of the vehicle Ÿ.
When the accelerator is pressed to the floor, the automatic gearbox shifts to
the next gear only after the engine reaches the specified maximum engine
speed.
Launch-Control Programme
The Launch-Control programme enables maximum acceleration while at a
standstill.
xDeactivating the TCS Ÿpage 210.
xPress and hold the brake pedal with your left foot.
xPlace the selector lever in position S or Tiptronic.
xPress the accelerator with the right foot until the vehicle reaches an
engine speed of approximately 3,200 rpm.
xLift the left foot off the brake Ÿ. The vehicle starts with maximum
acceleration.
xTurn on the TCS after accelerating!
WARNING
Rapid acceleration can cause loss of traction and skidding, especially on
slippery ground. This could cause loss of control of the vehicle resulting in
an accident and considerable damage.
xOnly use kick-down and rapid acceleration when weather conditions,
surface conditions and traffic conditions permit; accelerate and drive in a
manner that does not endanger other road users.
xPlease remember that the driven wheels can slip and the vehicle can
skid if the TCS is turned off, especially on slippery ground.
xTurn on the TCS after accelerating.

Driving209
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Caution
xIf you stop on a hill with a gear ratio engaged, do not try to prevent the
vehicle from rolling back by pressing on the accelerator. This could cause
overheating and damage the automatic gearbox.
xNever allow the vehicle to move with the gear selector lever in N, espe-
cially with the engine turned off. The automatic gearbox will not be lubricated
and could be damaged.
Recommended gear indication
In some vehicles, the recommended gear for reducing fuel consumption is
displayed on the instrument panel:
Information for cleaning the diesel particulate filter
The exhaust gas system control recognises when the diesel particulate filter
is blocked, and helps to clean it by recommending a specific gear for driving.
It may therefore be necessary to drive with the engine at an exceptionally high
speed Ÿpage 255.
WARNING
The recommended gear display is intended as a guideline only; it should
never replace the driver's attention to driving carefully.
xResponsibility for selecting the correct gear for each situation
continues to lie with the driver, for example when overtaking, climbing a
hill or towing a trailer.
For the sake of the environment
Selecting the most appropriate gear for the situation will help you to save
fuel.
Note
The recommended gear display is switched off when the clutch pedal is
pressed.
DisplayMeaning
ˆOptimum gear.
žRecommendation to change up a gear.
ŸRecommendation to change down a gear.
WARNING (continued)

Driving213
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xPress button . At the same time, press the brake pedal hard or gently
press the accelerator pedal with the engine switched on.
xThe control lamps G on the button and H on the instrument panel go
out.
Automatic release of the electronic parking brake on starting the engine
The electronic parking brake is automatically released when the vehicle starts
moving, if the driver's door is closed and the driver is wearing his/her seat
belt. In vehicles with a manual gearbox the clutch pedal should also be
pressed to the floor before starting the engine so that the system recognises
that the parking brake should be released.
Emergency braking function
Only use the emergency braking function if the vehicle cannot be stopped
with the brake pedal Ÿ!
xPull button hard to stop the vehicle. The warning display will be
accompanied by the corresponding warning chime.
xTo stop the braking process, release the button or press the accelerator.
WARNING
The incorrect use of the electronic parking brake may result in serious acci-
dent.
xNever use the electronic parking brake to brake the vehicle except in an
emergency. The braking distance is considerably longer, because braking
is only applied to the rear wheels. Always use the foot brake.
xNever accelerate from the engine compartment with the engine running
and a gear or a gear range engaged. The vehicle could move, even if the
parking brake is applied.
Note
In vehicles with a manual gearbox: When the clutch pedal is released and the
accelerator pressed at the same time, the electronic parking brake is auto-
matically released.
Note
If the vehicle battery is flat, it will not be possible to disconnect the electronic
parking brake. Use the jump-start Ÿpage 371.
Note
When the electronic parking brake is applied or released, noises may be
heard.
Note
If the electronic parking brake has not been used for a long while, the system
sometimes performs automatic and audible checks while the vehicle is at a
standstill.
Parking
When parking your vehicle, all legal requirements should be observed.
To park the vehicle
Complete operations only in the sequence given.
xPark the vehicle on a suitable surface Ÿ.
xPress and hold the brake pedal until the vehicle comes to a standstill.
xConnect the electronic parking brake Ÿpage 212.
xFor an automatic gearbox, move the selector lever to position P.
G
G

Driving215
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a discs by braking firmly a few times at a moderately high speed. Only do this
without endangering vehicles behind you or any other road users Ÿ.
Faults in the brake system
During braking, if you notice that the vehicle does not react as usual (that the
braking distance has increased suddenly) it may be possible that there is a
fault in the braking system. The
H warning lamp lights up and a text
message displayed. Take the vehicle to a qualified workshop immediately
and have the fault repaired. Drive at a moderate speed and be prepared to
use more pressure on the brake pedal, and allow for longer stopping
distances.
Brake servo
The brake servo only operates when the engine is running and the pressure
applied by the driver on the brake pedal increases.
If the brake servo does not operate or the vehicle must be towed, then the
brake pedal will have to be pressed with more force given that the braking
distance will be increased when the brake servo does not operate Ÿ.
WARNING
New brake pads do not brake to full efficiency.
xFor the first 320 km (200 miles), new brake pads have not yet reached
their maximum braking capacity, and need to be run in first. For this, to
compensate for reduced braking efficiency the brake pedal will have to be
pressed with more force.
xTo avoid losing control of the vehicle and causing serious accidents,
always take great care when driving with new brake pads.
xWhen running in new brake pads, always respect the safety distances
between you and other vehicles and do not cause situations requiring
extreme braking performance.
WARNING
When brakes overheat, braking is less efficient and braking distances
increase.
xWhen driving on slopes, brakes can be overloaded and overheat
quickly.
xReduce speed, move down a gear or select a shorter range of gears
before long steep slopes. This allows you to use the engine braking effect
and to reduce the strain on the brake system.
xNon-standard or damaged front spoilers could restrict the airflow to the
brakes and cause them to overheat.
WARNING
Wet, frozen or salt-covered brakes take time to brake and this increases
braking distances.
xTest the brakes carefully.
xDry the brakes, free them of ice and salt by braking gently several
times, when weather, road and traffic conditions permit.
WARNING
Driving without the brake servo may significantly increase the braking
distance and result in a severe accident.
xNever allow the vehicle to move forwards when the engine is switched
off.
xIf the brake servo does not operate or the vehicle must be towed, then
the brake pedal will have to be pressed with more force given that the
braking distance will be increased when the brake servo does not operate.

Driving223
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Auto Hold turns off automatically under the following conditions:
WARNING
The Auto Hold technology is limited by the laws of physics. The improved
comfort provided by Auto Hold should never prompt you to take risks.
xNever leave the vehicle running and with the Auto Hold function
switched on.
xAuto Hold cannot always stop the vehicle uphill and downhill (for
example, if the ground is slippery or frozen).
Caution
Before entering an automatic car wash, always switch the Auto Hold function
off, as it could be damaged when the electronic parking brake automatically
engages.
Start-Stop Function*
In Start-Stop mode, the engine is automatically switched off when the vehicle
is at a standstill. The engine restarts automatically when required.
The function is enabled automatically whenever the ignition is switched on.
The instrument panel displays information on the current status.
Vehicles with a manual gearbox
xWhen the vehicle is at a standstill, leave it in neutral and take your foot off
the clutch. The engine switches off.
xSimply depress the clutch pedal to move off again.
Vehicles with an automatic gearbox
xWhen the vehicle is at a standstill, depress the brake or keep it pressed
down. The engine switches off.
xThe engine will start again as soon as you release the brake pedal.
xWith the gear lever set to P, the engine will not start until a range of gears
is selected or the accelerator pedal is depressed.
manual gearboxAutomatic gearbox
1.If one of the conditions mentioned in table on page 222 changes.
2.If the engine is not running regularly or if there is a malfunction.
3.When changing to idle speed.If the selector lever is placed in
neutral (N).
4.If the engine is turned off or stalls.If the engine is switched off.
5.If the driver accelerates while
pressing the clutch in.If the vehicle is accelerated.
6.When one of the wheels has mini-
mal contact with the ground (for
example, on uneven ground).
Fig. 147 Detailed view of
the centre console: Start-
Stop function button.

Driving 224
Important conditions for the engine to automatically switch off
xThe driver seat belt must be buckled.
xThe driver door must be closed.
xThe bonnet must be closed.
xThe factory-fitted towing bracket must not be electrically connected to a
trailer.
xA minimum engine temperature has been reached.
xThe vehicle has moved since the last stop.
xIn vehicles with Climatronic: The temperature inside the vehicle is within
the preset temperature range.
xThe temperature set is neither very high nor very low.
xThe air conditioning defrost function is not switched on.
xIn vehicles with Climatronic: the blower has not been manually set to a
high speed.
xThe power level of the vehicle's battery is sufficient.
xThe vehicle's battery temperature is neither too high nor too low.
xThe vehicle is not on a steep gradient or slope.
xThe front wheels are not overly turned.
xThe heated windscreen is not switched on.
xReverse gear is not engaged.
xThe park assist system is not switched on.
Conditions for automatically restarting the engine
The engine may automatically restart under the following conditions:
xIf the vehicle interior is too hot or too cold.
xIf the vehicle moves.
xIf the vehicle's battery voltage drops.
Conditions requiring the key to restart the engine
The engine must be started using the key under the following conditions:
xIf the driver unbuckles his/her seat belt.
xIf the driver's door is opened.
xIf the bonnet is opened.
xIn vehicles with a manual gearbox: If a gear has been selected.
Switching Start-Stop mode on and off manually
xPress the button on the centre console Ÿpage 223, fig. 147.
xThe button will light up when the Start-Stop function is switched off.
The engine will start immediately if the vehicle is in Stop mode when it is
switched off manually.
WARNING
The brake servo and the power steering do not work when the engine is
switched off.
xNever allow the vehicle to move when the engine is switched off.
Caution
Using the Start-Stop function for a long period at very high outdoor tempera-
tures could damage the vehicle's battery.
Note
In some cases, you may have to restart the vehicle using the key. Observe the
corresponding message on the instrument panel display.
›

Driving227
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Optical parking system* (OPS)
The optical parking system is an accessory to the Parking sensor system
Ÿpage 226 and the park assist system Ÿpage 229.The zone recorded by the sensors in front of and behind the vehicle is
displayed on the factory-fitted radio or navigation system screen. Any obsta-
cles are display in relation to the vehicle Ÿ.
Zones explored
The zone in which obstacles are recognised runs to a distance of around 120
cm from the front of the vehicle and up to 60 cm to the side Ÿfig. 151 .
Behind the vehicle, the zone analysed reaches a distance of up to 160 cm and
around 60 cm to the sides Ÿfig. 150 .
Screen display
The image displayed represents the supervised zones in several segments.
As the vehicle moves closer to an obstacle, the segment moves closer to the
vehicle displayed Ÿfig. 150 and Ÿfig. 151 . When the penultimate
segment is displayed, this means that the vehicle has reached the collision
zone. Stop the vehicle!
Fig. 150 On-screen OPS
display: an obstacle
has been detected in the
collision zone. an
obstacle has been
detected in the segment.
zone recorded behind
the vehicle.AA
AB
AC
Fig. 151 On-screen OPS
display: an obstacle
has been detected in the
segment. zone
recorded behind the
vehicle.AA
AB
FunctionNecessary operations
Switching the display
on:Switch on the parking sensor system Ÿpage 226
or the park assist system Ÿpage 229. The OPS
switches on automatically.
Switching the display
off manually:
Press a zone selection button on the factory-fitted
radio or navigation system
OR: Briefly press the function button or
on the screen.
Switching the display
off manually:Drive forwards at more than about 10-15 km/h.
Select the reverse gear on vehicles with rear
assist Ÿpage 234. The display changes to the
image of the camera.
ERVC
AB
AC
ABAA