2010 Seat Alhambra child lock

Seats and storage compartments 148
Each rear seat can fold down individually to extend the luggage compart-
ment.
Folding the seats in the second row of seats for loading
xIf necessary, open the belt loop and wind up the seat belt by hand.
xIf it is necessary, remove the head rests on the integrated child seats then
reinstalled the integrated child seats Ÿpage 52.
xIf necessary, raise the armrests.
xRemove objects from the footrest area in front of and behind the rear seat
Ÿ.
xMove the rear seat all the way back.
xPush the head restraint down as far as it will go Ÿpage 10.
xIn the middle seat, close the drinks carrier in the rear of the centre
console, if necessary.
xPull lever Ÿpage 147, fig. 95 back and fold the backrest forwards.
The complete rear seat folds forward Ÿ.
xFold the backrest forwards until it locks into the load surface position
Ÿpage 147, fig. 95 .
xIf necessary, pull on the lever Ÿfig. 96 to move the seat to the
required position.
xWhen the seat is folded down, no adults or children should travel in it
Ÿ.
Folding the seats in the third row of seats for loading
xIf necessary, open the belt loop and wind up the seat belt by hand.
xOpen the tailgate.
xPush the head restraint down as far as it will go Ÿpage 10.
xRemove objects from the footrest area in front of and behind the rear seat
Ÿ.
xRemove objects from the space below the rear seat.
xRemove the attachment elements and supports for the net from the rail
system.
xPull lever Ÿfig. 96 back and fold the backrest forwards. The rear seat
folds forward Ÿ and the cushion also moves forward.
xFold the seat tray forward on top of the folded seat.
Fig. 96 Third row of seats: fold down the rear seat to
load then return to position .AAAB
A1
AB
A2
A1

Seats and storage compartments149
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xWhen the seat is folded down, no adults or children should travel in it
Ÿ.
Putting the seats in the second row back in place
xPull lever Ÿpage 147, fig. 95 upwards and place the seatback in
vertical position. The entire seat folds backwards.
xPull on the rear seats and the backrest to ensure that they are correctly
locked in place and that the safety belt protection is guaranteed for rear seat
passengers.
Putting the seats in the third row back in place
xOpen the tailgate.
xPull on the handle Ÿpage 148, fig. 96 to put the seat tray back in
position.
xPull on the handle Ÿpage 148, fig. 96 . The entire seat folds back-
wards.
xPress on the seat tray in the backrest until it is held in position by its
magnets.
xOpen the sliding door.
xPut the backrest into position and press firmly until it clicks into place.
xPull on the rear seats and the backrest to ensure that they are correctly
locked in place and that the safety belt protection is guaranteed for rear seat
passengers.
WARNING
Folding and lifting the rear seats carelessly without paying attention could
cause serious injury.
xNever fold or lift the seats while driving.
xDo no trap or damage seat belts when raising the backrest.
xKeep your hands, fingers, feet and other body parts out of the hinges
and the seat locking mechanism when folding and unfolding.
xMats or other objects can be caught in the hinges of the backrests or
rear seat. This could prevent the seat or backrest from locking securely in
the vertical position.
xAll backrests must engage correctly for the seat belts on the rear seats
to work properly. When the backrest of an occupied seat is not correctly
locked in place, the passenger can be thrust forward with the backrest in
case of sudden braking, sudden manoeuvres or an accident.
xNo seat must be occupied if the backrest or seat is folded or not
correctly engaged.
Caution
Before folding the backrest of the rear seat, adjust the front seats so that the
head restraint or backrest do not hit them when it is folded.
Caution
xObjects placed in the footrest area in front of and behind the rear seats
can be damaged when seats are folded down or put back into position.
Remove any objects in the way before folding seats down or repositioning
them.
xObjects placed in the moulding on the back of the third row of seats can
be damaged when folding down the seats or putting them back into position.
Remove any objects in the way before folding seats down or repositioning
them.
xThe attachment elements and supports for the net partition placed on the
rail system can be damaged when folding down seats from the third row or
putting them back into position and these can also damage the seats them-
selves. Before folding down or repositioning the seats, remove the attach-
ment elements and supports for the net from the rail system.
A1
A2
A3
WARNING (continued)

Seats and storage compartments 176
Vehicle socketsMaximum power consumption
The maximum capacity of each socket must not be exceeded. The power
consumption is indicated on the rating plate of each appliance.
Where two or more appliances are connected at the same time, the total
rating of all the connected devices must never exceed 190 Watts Ÿ.
12 volt socket
The 12 Volt socket will only work with the ignition on.
Using electrical appliances with the engine stopped and the ignition
switched on will drain the battery. Therefore, electrical consumers connected
to the socket must only be used when the engine is running.
To prevent voltage variations from causing damage, switch off the electrical
consumer connected to the 12 Volt socket before switching the ignition on or
off and before starting the engine.
12 Volt sockets can be found in the following locations in the vehicle:
xCompartment in the centre of the centre console.
xCompartment in the front centre console.
xStorage compartment in the front central armrest.
xRear centre console Ÿfig. 126.
xAt the rear right of the luggage compartment.
230 Volt Euro socket*
The socket only works when the engine is running Ÿ.
Connecting an electrical appliance: Plug the appliance into the socket as far
as possible to unlock the built-in child safety device. The current only flows
when the child safety device is unlocked.
Fig. 126 Centre console,
rear section: 12 volt
socket.
Fig. 127 Rear centre
console: 230 Volt Euro
socket.
SocketMaximum power consumption
12 Volts120 Watts
230 Volts150 Watts (300 Watt peak)

Seats and storage compartments177
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Heat protection
The 230 Volt Euro power connector converter switches off automatically when
a certain temperature is exceeded. This disconnect prevents overheating in
the event of an increase in power consumption of the connected appliance
and where the atmospheric temperature is too high. The converter will switch
on again automatically after it has cooled down. Appliances that are switched
on and connected to the socket will start up again. Therefore, switch off all
electrical appliances connected to the socket when the current converter
switches off due to overheating.
WARNING
High voltage in the electrical installation!
xLiquids must not be spilt over the socket.
xDo not plug adapters or extension cords into the 230 Volt Euro power
connector. Otherwise, the built-in child safety device will switch off and the
connector will become live.
xDo not plug current conductors such as a knitting needle into the 230
Volt Euro power connector.
Caution
xAlways follow the operating instructions for the appliances to be
connected!
xNever exceed the maximum power rating as this could damage the
vehicle's general electrical system.
x12 volt socket:
Only use accessories with approved electromagnetic compatibility
according to current regulations.
Never power the socket.
x230 Volt Euro socket:
Do not hang appliances or plugs that are too heavy (e.g. a transformer)
from the socket.
Do not connect lamps which contain a neon tube.
Only plug appliances with a voltage that matches the socket voltage
into the socket.
In the event of consumers with a high start-up current, surge protection
prevents them from switching on. In this case, unplug the consumer and
try plugging it back in after around 10 seconds.
Note
Some appliances may not work properly in the 230 Volt Euro power connector
due to a lack of power (Watts).
Note
The 230 Watt Euro power connector can be modified for 115 Watt appliances
and vice versa. Consult a specialist shop for advice on accessories to adapt
the connector. SEAT recommends visiting a qualified workshop.
LED on the socket Ÿpage 176, fig. 127
Steady green light:The child safety device is unlocked. The
socket can now be used.
Flashing red light:There is some kind of fault (e.g. discon-
nection due to excess current or tempera-
ture).

Driving 196
Ignition lock
Key not authorised for the vehicle
If a key which is not authorised for this vehicle is inserted in the ignition lock,
it can be removed as follows:
xAutomatic gearbox: the key cannot be removed from the ignition lock.
Press and release the selector lever locking button. Key can be removed from
the vehicle.
xManual gearbox: Remove the key from the ignition.
WARNING
Unsuitable or careless use of the vehicle key could result in serious injury.
xAlways take all the keys with you whenever you leave the vehicle. The
engine could accidentally be started and electrical equipment such as the
windows could accidentally be operated resulting in serious injury.
xNever leave children or disabled people alone in the car. They could be
trapped in the car in an emergency and will not be able to get themselves
to safety. For example, depending on the time of the year, temperatures
inside a locked and closed vehicle can be extremely high or extremely low
resulting in serious injuries and illness or even death, particularly for
young children.
xNever remove the key from the ignition if the vehicle is in motion. The
steering may lock and it will not be possible to turn the steering wheel.
Note
If the key is left in the ignition lock with the engine off for long periods, the
vehicle battery will run flat.
Fig. 134 Vehicle key positions
Car keys Ÿfig. 134
No key in the ignition lock: The steering lock may be activated.
Ignition off, all electrical components disconnected. Key can be
removed from the vehicle.
Ignition is switched on. Pre-heating of diesel engine. The steering
lock can be unlocked.
Switch on the engine. Release the key when the engine has started.
When it is released, the key returns to position .
A0
A1
A2A1

Driving 210
Braking, stopping and parking
Introduction
The assisted braking systems include the anti-lock braking system (ABS), the
brake assist system (BAS), the electronic differential system (EDS), the trac-
tion control system (TCS) and the electronic stabilisation program (ESP).
Additional information and warnings:
xTo wi ng m o d e Ÿpage 260
xStart assist systems Ÿpage 221
xWheels and tyres Ÿpage 323
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Driving with worn brake pads or a faulty brake system may lead to serious
accident.
xIf I lights, alone or accompanied by a warning message on the instru-
ment panel, please go immediately to a specialist workshop to check the
brake pads and to replace them if they are worn.
WARNING
Careless parking can cause serious injury.
xNever remove the key from the ignition if the vehicle is in motion. The
steering lock may engage and locked the steering wheel making the
vehicle impossible to control.
xAlways park your vehicle so that no part of the exhaust system can
come in contact with flammable materials (such as wood, leaves, spilled
fuel, dried grass, etc).
xAlways apply the electronic parking brake when you leave your vehicle
and when you park.
xNever leave children or disabled people alone in the vehicle. They could
release the electronic parking brake, activate the selector lever or gear
stick and start the vehicle moving. This could result in serious accident.
xAlways take all the keys with you whenever you leave the vehicle. The
engine could accidentally be started and electrical equipment such as the
windows could accidentally be operated resulting in serious injury.
xNever leave children or disabled people alone in the car. They could be
trapped in the car in an emergency and will not be able to get themselves
to safety. For example, depending on the time of the year, temperatures
inside a locked and closed vehicle can be extremely high or extremely low
resulting in serious injuries and illness or even death, particularly for
young children.
Caution
xSpecial care should be taken when parking in areas with high kerbs or
fixed barriers. Objects protruding from the ground may damage the bumper
or other parts of the vehicle during manoeuvres. To avoid damage, stop
before the wheels touched the barrier or kerb.
xSpecial attention is required when driving through entrances, over ramps,
kerbs or other objects. The vehicle underbody, bumpers, mudguards and
running gear, and the engine and exhaust system could be damaged as you
drive over these objects.
WARNING (continued)

Driving 214
xSwitch off the engine and release the brake pedal.
xRemove the key from the ignition.
xIf necessary, turn the steering wheel slightly to lock the steering.
xWith a manual gearbox, engage the 1st gear on flat ground and slopes, or
even the reverse gear on hills, and release the clutch pedal.
xEnsure that all passengers leave the vehicle, especially children.
xWhen leaving the vehicle, take all keys with you.
xLock the vehicle.
Additional information for steep slopes and hills
Before switching off the engine, rotate the steering wheel so that if the
vehicle should move then it will be held by the kerb.
xOn slopes, turn the front wheels so that they are against the edge of the
kerb.
xUphill, turn the wheels towards the centre of the road.
WARNING
The components of the exhaust system reach very high temperatures. This
could cause a fire and considerable damage.
xAlways park your vehicle so that no part of the exhaust system can
come in contact with flammable materials (such as wood, leaves, spilled
fuel, dried grass, etc).
Caution
xSpecial care should be taken when parking in areas with high kerbs or
fixed barriers. Objects protruding from the ground may damage the bumper
or other parts of the vehicle during manoeuvres. To avoid damage, stop
before the wheels touched the barrier or kerb.
xSpecial attention is required when driving through entrances, over ramps,
kerbs or other objects. The vehicle underbody, bumpers, mudguards and running gear, and the engine and exhaust system could be damaged as you
drive over these objects.
Information about the brakes
For the first 200 to 300 km (100 to 200 miles), new brake pads have not yet
reached their maximum braking capacity, and need to be run in first Ÿ.
The slightly reduced braking effect can be compensated for by increasing
pressure on the brake pedal. While running in, the full braking distance or
emergency braking distance is larger then when the brake pads have been
run in. While running in, avoid full power braking or situations requiring
braking performance. For example, in heavy traffic.
The rate of wear of the brake pads depends to a great extent on the condi-
tions in which the vehicle is used and the way the vehicle is driven. If the
vehicle is used frequently in city traffic or for short trips or driven sport style,
visit a specialist workshop regularly more frequently than advised in the
Maintenance Programme to have the bake pads checked.
If you drive with wet brakes, for example, after crossing areas of water, in
heavy rainfall or even after washing the car, the effect of the brakes is less-
ened as the brake discs are wet or even frozen (in winter). At higher speed,
dry the brakes as quickly as possible by braking gently several times. Only do
this without endangering vehicles behind you or any other road users Ÿ.
A layer of salt on the discs and brake pads will reduce brake efficiency and
increase braking distance. If you drive for a prolonged period on salted roads
without braking then brake carefully several times to eliminate the layer of
salt on the brakes Ÿ.
If the vehicle remains parked for considerable lengths of time, is used little,
or if the brakes are not used, there may be corrosion on the brake discs and
a buildup of dirt on the brake pads. If the brakes are not used frequently, or
if rust has formed on the discs, SEAT recommends cleaning the pads and

Checking and refilling levels303
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xRotate the shut off on the cover clockwise Ÿpage 302, fig. 171 and open
the cover forwards.
xUnscrew the tank filler neck cap Ÿpage 302, fig. 172 anticlockwise.
Refilling AdBlue
Only use AdBlue that is approved by SEAT and that complies with the ISO
22241-1 Standard. Only use genuine bottles.
xObserve the instructions and information provided by the refill bottle
manufacturer.
xObserve the expiry date.
xUnscrew the cap on the refill bottle.
xPlace the refill bottle upside down inside the tank filler neck.
xPress the refill bottle against the filler neck and keep in this position.
xAdd at least 10 litres of AdBlue (6 bottles). A lower quantity would be
insufficient.
xWait until the contents of the refill bottle have been poured into the
AdBlue tank. Do not crush or damage the bottle!
xUnscrew the liquid bottle anticlockwise and remove it carefully Ÿ.
xYou can tell when the AdBlue tank is full because the bottle will be empty.
Closing the tank filling neck
xScrew on the tank filler neck cap Ÿpage 302, fig. 172 clockwise until
it is fully inserted.
xPlace the cover and turn the shut off anticlockwise to close it.
Operations before driving
xOnly switch the ignition on after refilling.
xKeep the ignition switch on for at least 30 seconds so that the system
detects tank refilling.
xWait 30 seconds before starting the engine!
WARNING
Only keep AdBlue in its original container, tightly shut and in a safe place.
xNever keep AdBlue in empty food cans, bottles or other containers to
avoid other people mistaking it for something else.
xKeep the AdBlue out of the reach of small children.
Caution
xOnly refill using AdBlue expressly approved by SEAT. The use of any other
type of AdBlue could cause engine damage!
xAdBlue should never be mixed with water or any other additives. Any type
of damage caused by a mixture will not be covered by the warranty.
xDo not add AdBlue to the diesel fuel tank! Otherwise you may damage the
engine.
xNever leave the refill bottle in the vehicle. It could become permeable due
to temperature changes and bottle damage and the AdBlue could damage
the vehicle interior.
For the sake of the environment
Dispose of the refill bottle in an environment-friendly manner.
Note
Suitable AdBlue refill bottles can be purchased from a qualified workshop.
A1
A2
A1