2010 Seat Alhambra headlights

Vehicle maintenance and cleaning 270
For the sake of the environment
The remains of car care products should not be disposed of with ordinary
household waste. Observe information provided by the manufacturer.
Washing the vehicle
The longer substances such as insects, bird droppings, resinous tree sap,
road dirt, industrial deposits, tar, soot or road salt and other aggressive mate-
rials remain on the vehicle, the more damage they do to the paintwork. High
temperatures (for instance due to strong sunlight) further intensify the corro-
sive effect. The vehicle undercarriage should also be thoroughly washed at
regular intervals.
Automatic car washes
Always observe the instructions provided at the automatic car wash. The
standard precautionary measures prior to entering the car wash should be
taken to avoid damage to the vehicle (close all windows, fold in exterior
mirrors). If the vehicle is fitted with additional components (spoiler, roof-rack,
aerial...), check with the car wash supervisor whether these can enter the car
wash Ÿ.
The vehicle paintwork is so durable that the car can normally be washed
without problems in an automatic car washing tunnel. However, wear and
damage to the paintwork will depend on the type of car wash used. SEAT
recommends the use of car washed without brushes.
To remove traces of wax on windows and to prevent wiper blades from
scratching, please observe the following Ÿpage 272, “Cleaning windows
and exterior mirrors”.
Washing the car by hand
When washing the car by hand, use plenty of water to soften the dirt first, and
rinse off as well as possible.Then clean the vehicle with a soft sponge, glove or brush using only slight
pressure. Start at the roof and work downwards. Special car shampoo should
only be used for very persistent dirt.
Rinse the sponge or glove thoroughly and often.
Wheels, sills and similar should be cleaned last. Use a second sponge for
this.WARNING
Sharp components on the vehicle may cause injury.
xProtect arms and hands from sharp edges when cleaning the vehicle
undercarriage or the interior of the wheel hubs.
WARNING
After the vehicle has been washed, the braking effect will be reduced (and
the braking distance increased) due to moisture (and ice in winter) on the
brakes.
xDry the brakes and remove ice by braking carefully. Ensure that you are
not endangering other road-users or breaking traffic regulations in the
process.
Caution
xThe temperature of the water must not exceed +60 °C (+140 °F).
xTo avoid damage to the paintwork, do not wash the vehicle in full sun.
xDo not use rough sponges or similar which could damage the surface to
clean away the traces of insects.
xNever wipe the headlights with a dry cloth or sponge, always moisten
first. It is best to use soapy water.

Checking and refilling levels 296
Closing the tank cap
xScrew on the tank cap clockwise until it you hear it click into position.
xPress the tank flap until you hear it click into place. The tank flap must be
flush with the body contour.
WARNING
Do not continue refilling once the fuel nozzle has switched itself off. The
fuel tank may be filled too much. As a result, fuel may spurt out and spill.
This could lead to a fire, explosion and severe injuries.
Caution
xAlways remove any fuel spilled on the vehicle paintwork immediately to
avoid damage to the wheel housing, the tyre and vehicle paintwork.
For the sake of the environment
Spilt fuel can contaminate the environment.
Refilling precautions
Information on bulb replacement Ÿpage 360.
Checklist
Never work on the engine or in the engine compartment if you are not familiar
with the operations to be carried out, the applicable safety standards and
especially if you do not have the instruments, liquids and tools necessary
Ÿpage 304, “Working in the engine compartment”! Have the work carried
out by a qualified workshop if you are uncertain. Check the following regu-
larly, preferably when you refuel:
xWindscreen washer fluid level Ÿpage 124
xEngine oil level Ÿpage 309
xEngine coolant level Ÿpage 313
xBrake fluid level Ÿpage 210
xTyre pressure Ÿpage 323
xVehicle lighting required to guarantee road safety:
–Indicators
– Side lights, dipped headlights and full beam headlights
– Rear lights
–Brake lights
– Rear fog light Ÿpage 116
WARNING
Not following the checklist prepared for your own safety could lead to acci-
dents and severe injuries.
xAlways follow the check list and perform the necessary operations.

If and when 362
13. Check if the new bulb is working. If the bulb is not working, it may not
have been correctly fitted, it could be damaged or the connector may not
be correctly connected.
14. Every time a bulb for the headlights is replaced, visit a specialised work-
shop to check the headlights.
WARNING
Failure to follow the checklist prepared for your own safety could lead to
accidents and severe injuries.
xAlways complete the operations given in the checklist and observe the
general rules of safety.
Caution
Always remove and fit headlights carefully to avoid damage to the paintwork
and other vehicle parts.
To replace halogen headlight bulbs
There is no need to remove the headlight to replace bulbs.
Complete operations only in the sequence given:
WARNING (continued)
Fig. 213 In the engine
compartment: Left-hand
side headlight lining.
dipped beam headlights,
daytime lights and
main beam headlights
and side lights.
AA
ABAC
Fig. 214 Left headlight

If and when363
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Note
The images show the left hand headlight from behind. The structure of the
right hand side headlight is symmetric.
page 362, fig. 213,
page 362, fig. 214 Indicators (small lamp
holder)Dipped beam head-
lightsDaylight driving lightsMain beam headlightsSide lights
1.Always take the checklist into account and take the necessary actions Ÿpage 361.
2.Open the bonnet ’ Ÿpage 304.
3.Remove the rubber cover on the rear of the headlight.
4.
Rotate the lamp holder
to the left all the way
and pull it out back-
wards with the bulb.
Rotate the lamp holder to the left all the way and
pull it out backwards with the bulb.
Press the wire clip down-
wards and pull the lamp
holder out with the
bulb.Pull the lamp holder
out backwards with the
bulb.
5.Depending on the model, the bulb is removed directly from the lamp holder or it may need to be rotated and then removed.
6.Replace the faulty bulb by a new identical bulb.
7.Place the bulb holder in the headlight and rotate to the right all the way.
Place the lamp holder in
the headlight and pull the
wire clip upwards until it
clicks into place.Place the lamp holder in
the headlight and insert
completely.
8.Insert the rubber cover.
AAABAC
A1A2
A3

If and when 364
To replace the xenon headlights bulb
There is no need to remove the headlight to replace bulbs.
Complete operations only in the sequence given:Always seek the help of a specialist when changing the Xenon dipped beam
and full beam headlamps Ÿ in “Introduction” on page 360.
Note
The illustrations show the left hand headlight. The structure of the right hand
side headlight is symmetric.
Fig. 215 In the engine
compartment: Turn signal
cover.
Fig. 216 Turn signal indi-
cator lamp holder and
turning light .A1A2
Turn signal indicators Turning lights
1.Always take the checklist into account and take the necessary
actions Ÿpage 361.
2.Open the bonnet ’ Ÿpage 304.
3.Rotate the cover Ÿfig. 215 in the direction of the arrow and remove
it.
4.
Rotate the lamp holder
Ÿfig. 216 to the left all the way
and pull it out backwards with the
bulb.Press the wire clip downwards
and pull the lamp holder
Ÿfig. 216 out with the bulb.
5.Depending on the model, the bulb is removed directly from the lamp
holder or it may need to be rotated and then removed.
6.Replace the faulty bulb by a new identical bulb.
7.Place the bulb holder in the head-
light and rotate to the right all the
way.Place the lamp holder in the
headlight and pull the wire clip
upwards until it clicks into place.
8.Rotate the cover Ÿfig. 215 in the opposite direction to the arrow as
far as it will go.
A1A2
A1
A2

If and when365
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
To replace the front bumper bulbs
Complete operations only in the sequence given:
Fig. 217 On the right-
hand side of the front
bumper: Removing the
headlights
Fig. 218 Changing the
bulbs in the headlights.
1.Always take the checklist into account and take the necessary
actions Ÿpage 361.
2.Pull the cover forwards, in the direction of the arrow Ÿfig. 217.
3.Unscrew the attachment screw Ÿfig. 217 using the screwdriver
from the on-board tools Ÿpage 353.
4.Tilt the headlight slightly forward and extract it from its lateral
attachments Ÿfig. 218 (small arrows).
5.Release the connector Ÿfig. 218 and remove it.
6.Rotate the lamp holder Ÿfig. 218 to the left all the way, in the
direction of the arrow, and pull it out backwards with the bulb.
7.Replace the faulty bulb by a new identical bulb.
8.Place the bulb holder in the headlight and rotate to the right all the
way.
9.Insert the connector Ÿfig. 218 on the lamp holder Ÿfig. 218
. The connector must audibly click into place.
10.Place the headlight into its position Ÿfig. 218 (small arrows) and
tilt it backwards.
11.Tighten the attachment screw Ÿfig. 217 using the screwdriver.
12.Replace the cover on the bumper Ÿfig. 217.
A1
A1
A2
A1
A2
A1

If and when373
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a The vehicles should not touch. Otherwise, current may be allowed to flow
when the positive poles are connected.
Connect the clamps so they have good metal-to-metal contact with the termi-
nals.
If the engine fails to start straight-away, switch off the starter after about 10
seconds and try again after about a minute.
Complete operations only in the sequence given.
Jump lead terminal connections
xSwitch off the ignition of both vehicles Ÿpage 195.
xLikewise, open the battery cover in the engine compartment Ÿpage 318,
or remove the positive pole cap from one side 3), in the direction of the arrow
Ÿpage 372, fig. 225.
xConnect one end of the red jump lead to the positive terminal
Ÿpage 372, fig. 226 or Ÿpage 372, fig. 225 of the vehicle with the
flat battery Ÿ.
xConnect the other end of the red jump lead to the positive terminal in
the vehicle providing assistance .
xFor vehicles without Start-Stop system: Connect one end of the black
jump lead to the negative terminal in the vehicle providing assistance
Ÿpage 372, fig. 226.
xFor vehicles with Start-Stop system: Connect one end of the black
jump lead to a suitable ground connection, a solid piece of metal in the
engine block, or to the engine block Ÿpage 372, fig. 227.
xConnect the other end of the black jump lead to a solid metal compo-
nent connected to the engine block, or onto the engine block itself of the
vehicle with the flat battery however, connect it as far away as possible from
the battery Ÿ.
xPlace the leads so that they cannot be caught by any moving parts in the
engine compartment.Switching on
xStart the engine of the vehicle supplying current and let it run at idling
speed.
xStart the engine of the car with the flat battery and wait two or three
minutes until the engine is “running smoothly”.
Removing the jump leads
xBefore you remove the jump leads, switch off the headlights (if they are
switched on).
xTurn on the heating and rear window heater in the vehicle with the flat
battery. This helps minimise voltage peaks which are generated when the
leads are disconnected.
xWith the engines running, disconnect the leads in reverse order to
connection.
xClose the battery cover, or replace the positive pole cap 3).
WARNING
Incorrectly jump starting could cause the battery to explode resulting in
serious injury. Please observe the following rules to minimise the risk of a
battery explosion:
xAll work involving the vehicle battery and electrical system can cause
corrosion, fire and serious electric shocks. Always read and take into
account the safety warnings and standards before beginning work on the
battery Ÿpage 318, “Vehicle battery”.
xAlways protect your eyes with suitable working goggles and never lean
over the vehicle battery.
xThe jump leads must be connected in the correct order: first the positive
cable, then the negative cable.
xDo not attach the negative cable to parts of the fuel system or to the
brake hose/pipe.
3)Vehicles whose battery is not located in the engine compartment Ÿpage 372.
A+A+AA
A+AB
A-AB
AX
AX
AA

Index393
Index
"Safe" security system . . . . . . . . . . . . . . . . . . . . 88
A
Abroad
Extended stay abroad with your vehicle . . 283
Sale of vehicle . . . . . . . . . . . . . . . . . . . . . . . 283
ABS
See "Braking assist systems" . . . . . . . . . . . 216
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
Adaptive headlights
Adaptive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
AdBlue
Control lamp . . . . . . . . . . . . . . . . . . . . . . . . 300
Information . . . . . . . . . . . . . . . . . . . . . . . . . 301
Minimum quantity for a refill . . . . . . . . . . . 301
Refilling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
Specifications . . . . . . . . . . . . . . . . . . . . . . . 303
Tank filling capacity . . . . . . . . . . . . . . . . . . . 301
Warning lamp . . . . . . . . . . . . . . . . . . . . . . . . 300
Additional equipment . . . . . . . . . . . . . . . . . . . . 286
Additional heater
See "Auxiliary heater" . . . . . . . . . . . . . . . . . 187
Adjusting passenger exterior mirror . . . . . . . . . 132
Adjustment
Correct sitting position . . . . . . . . . . . . . . . . . 12
Electric front seat . . . . . . . . . . . . . . . . . . . . . 135Head restraints . . . . . . . . . . . . . . . . . . . . . . 143
Mechanical front seat . . . . . . . . . . . . . . . . . 134
Rear seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Seat with position memory . . . . . . . . . . . . . 138
Steering wheel . . . . . . . . . . . . . . . . . . . . . . . 194
Adjustments
Folding the backrest of the front passenger's
seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Headlight range . . . . . . . . . . . . . . . . . . . . . . 120
Aerial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
Aerial built into the window . . . . . . . . . . . . . . . 283
AFS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Air conditioning
see "Climate control" . . . . . . . . . . . . . . . . . 179
Air recirculation mode . . . . . . . . . . . . . . . . . . . . 185
Air vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Airbag system . . . . . . . . . . . . . . . . . . . . . . . . 29, 33
Cleaning instrument panel . . . . . . . . . . . . . 281
Curtain airbags . . . . . . . . . . . . . . . . . . . . . . . 40
Deactivating the front passenger airbag . . . 36
Deactivating using the key switch . . . . . . . . 36
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Differences between front passenger airbag
systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
Front airbags . . . . . . . . . . . . . . . . . . . . . . . . . 34
Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Knee airbag . . . . . . . . . . . . . . . . . . . . . . . . . . 41Locking the vehicle after airbag deployment . .
84
Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
Side airbags . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Use of child seats . . . . . . . . . . . . . . . . . . . . . 36
Vehicle care . . . . . . . . . . . . . . . . . . . . . . . . . 281
Warning lamp . . . . . . . . . . . . . . . . . . . . . . . . 31
Alarm system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Alcantara . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
All-wheel drive
Snow chains . . . . . . . . . . . . . . . . . . . . . . . . . 332
Winter tyres . . . . . . . . . . . . . . . . . . . . . . . . . 331
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
Ambient lighting . . . . . . . . . . . . . . . . . . . . . . . . 121
Anodized surfaces . . . . . . . . . . . . . . . . . . . . . . . 275
Antifreeze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
Anti-lock brake system (ABS) . . . . . . . . . . . . . . 216
Antitheft alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
Antitheft alarm system
Anti-tow system . . . . . . . . . . . . . . . . . . . . . . . 90
False alarms . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Interior monitoring . . . . . . . . . . . . . . . . . . . . 90
Antitheft bolts . . . . . . . . . . . . . . . . . . . . . . . . . . 354
Anti-theft locking bolts . . . . . . . . . . . . . . . . . . . 339
Anti-theft wheel locking bolts . . . . . . . . . . . . . . 340
Anti-tow system . . . . . . . . . . . . . . . . . . . . . . . . . . 90