2010 Seat Alhambra fuel cap

Checking and refilling levels303
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xRotate the shut off on the cover clockwise Ÿpage 302, fig. 171 and open
the cover forwards.
xUnscrew the tank filler neck cap Ÿpage 302, fig. 172 anticlockwise.
Refilling AdBlue
Only use AdBlue that is approved by SEAT and that complies with the ISO
22241-1 Standard. Only use genuine bottles.
xObserve the instructions and information provided by the refill bottle
manufacturer.
xObserve the expiry date.
xUnscrew the cap on the refill bottle.
xPlace the refill bottle upside down inside the tank filler neck.
xPress the refill bottle against the filler neck and keep in this position.
xAdd at least 10 litres of AdBlue (6 bottles). A lower quantity would be
insufficient.
xWait until the contents of the refill bottle have been poured into the
AdBlue tank. Do not crush or damage the bottle!
xUnscrew the liquid bottle anticlockwise and remove it carefully Ÿ.
xYou can tell when the AdBlue tank is full because the bottle will be empty.
Closing the tank filling neck
xScrew on the tank filler neck cap Ÿpage 302, fig. 172 clockwise until
it is fully inserted.
xPlace the cover and turn the shut off anticlockwise to close it.
Operations before driving
xOnly switch the ignition on after refilling.
xKeep the ignition switch on for at least 30 seconds so that the system
detects tank refilling.
xWait 30 seconds before starting the engine!
WARNING
Only keep AdBlue in its original container, tightly shut and in a safe place.
xNever keep AdBlue in empty food cans, bottles or other containers to
avoid other people mistaking it for something else.
xKeep the AdBlue out of the reach of small children.
Caution
xOnly refill using AdBlue expressly approved by SEAT. The use of any other
type of AdBlue could cause engine damage!
xAdBlue should never be mixed with water or any other additives. Any type
of damage caused by a mixture will not be covered by the warranty.
xDo not add AdBlue to the diesel fuel tank! Otherwise you may damage the
engine.
xNever leave the refill bottle in the vehicle. It could become permeable due
to temperature changes and bottle damage and the AdBlue could damage
the vehicle interior.
For the sake of the environment
Dispose of the refill bottle in an environment-friendly manner.
Note
Suitable AdBlue refill bottles can be purchased from a qualified workshop.
A1
A2
A1

Checking and refilling levels305
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xWhen the engine is warm or hot, the cooling system is pressurised! Do
not unscrew the cap on the expansion tank when the engine is hot. Other-
wise, coolant may spray out under pressure causing burns and serious
injury.
Carefully and slowly unscrew the cap anticlockwise, gently pressing
down on it.
Always protect your face, hands and arms from hot coolant and
steam using a large, thick cloth.
xWhen refilling liquids, avoid spilling them on parts of the engine and
the exhaust system. Spilled liquids could cause a fire.
WARNING
The high voltages of the electrical system can give electric shocks as well
as causing burns and serious injury and possibly even death!
xNever cause short circuits in the electrical system. The battery could
explode.
xTo minimise the risk of electric shock and serious consequences while
the engine is running or starting the engine, note the following:
Never touch the electrical wiring of the ignition system.
Never touch electric cables or the gas discharge lamps.
WARNING
In the engine compartment, there are rotating parts that could cause
serious injury.
xNever place your hands on or near the radiator fan. Touching the rotor
blades could seriously harm you. The ventilator works according to the
engine temperature and could start suddenly even when the ignition is
turned off and the key is removed.
xIf any work has to be performed when the engine is started or with the
engine running, there is an additional, potentially fatal, safety risk from the
rotating parts, such as the drive belts, alternator, radiator fan etc as well as
from the high-voltage ignition system. Always work with the utmost
caution.
Always make sure that no parts of your body, jewellery, ties, loose
clothing and long hair can be trapped by the rotating parts of the
engine. Before any work, remove ties and jewellery ( necklaces, etc), tie
longhair back and tie all items of loose clothing to your body to make
sure that they cannot be trapped by engine components.
Take extreme caution when operating the accelerator and remain
attentive. The vehicle could move, even with the electronic parking
brake activated.
xAlways make sure you have not left any objects, such as cloths or tools,
in the engine compartment. If any object is left in the engine compartment,
this could cause malfunctions, engine faults and even a fire.
WARNING
Refill liquids and certain materials can catch fire easily in the engine
compartment, causing a fire and serious injury!
xNever smoke.
xNever work close to places exposed to flames or sparks.
xNever pour service fluids over the engine. These fluid may ignite hot
engine parts and cause injuries.
xIf it is necessary to work on the fuel system or the electrical system,
please follow the instructions below:
Always disconnect the vehicle battery. When disconnecting the
battery, ensure that the vehicle is unlocked otherwise the antitheft
alarm will be triggered.
WARNING (continued)WARNING (continued)

Wheels and tyres325
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
About your tyres and wheels
The tyres of a vehicle are the components which are subjected to most stress
and are the most underestimated. Tyres are very important, as the support
offered by their narrow surface is the only point of contact between the
vehicle and the road.
The service life of tyres is dependent on tyre pressure, driving style, the care
they receive and the correct fitting.
The tyres and wheel rims are an essential part of the vehicle's design. The
tyres and rims approved by SEAT are specially matched to the characteristics
of the vehicle and our critical to good road holding and safe handling.
Avoiding damage to tyres and wheels
xIf you have to drive over a kerb or similar obstacle, drive very slowly and
as near as possible at a right angle to the kerb.
xInspect the tyres regularly for damage (punctures, cuts, cracks, dents).
xRemove any foreign bodies found on the outside of the tread provided
they have not passed through the wall of the tyre Ÿpage 330.
xThe instructions for tyre control systems should always be observed.
xReplace damaged or worn tyres as soon as possible Ÿpage 330.
xRegularly check tyres for non-visible damage Ÿpage 330.
xNever exceed the maximum permitted speed or loads specified for the
type of tyre fitted on your vehicle Ÿpage 333.
xDo not allow tyres to come into contact with aggressive substances,
grease, oil, fuel or brake fluid Ÿ.
xLost valve caps should be replaced immediately.
Tyres with directional tread pattern
Tyres with directional tread pattern have been designed to operate best when
rotating in only one direction. An arrow on the tyre sidewall indicates the
direction of rotation on tyres with directional tread Ÿpage 333. Always
observe the direction of rotation indicated when mounting the wheel. This
guarantees optimum grip and helps to avoid aquaplaning, excessive noise
and wear.
If the tyre is mounted in the opposite direction of rotation, drive with extreme
caution, as the tyre is no longer being used correctly. This is of particular
importance when the road surface is wet. Change the tyre as soon as possible
or remount it with the correct direction of rotation.
Interchanging tyres
To ensure that the wear is equal on all tyres the wheels should be changed
round from time to time according to the system Ÿfig. 182. All the tyres will
then last for about the same time.
SEAT recommends you take the vehicle to a qualified workshop to have the
tyres changed.
Tyres that are over 6 years old
Tyres are subject to an ageing process as a result of physical and chemical
processes. This may affect their performance. Tyres which are stored for long
periods of time without being used, harden and become more fragile than
tyres which are in constant use.
Fig. 182 Diagram for
changing wheels

Wheels and tyres 328
vendor should provide the manufacturer's certificate with the tyre, indicating
that this type of tyre is suitable for your vehicle. This certificate should always
be carried with the vehicle.
Tyre pressures
Fig. 183 Position of tyre pressure specification plate.
The correct tyre pressures for tyres fitted at the factory is shown on a label and
is valid for summer and winter tyres. This label Ÿfig. 183 is either in the
driver's door strut or inside the fuel cap.
Under-inflation or over-inflation will reduce the life of the tyres considerably
and also impair the car's handling Ÿ. It is essential to maintain the
correct tyre pressures, especially if driving at high speeds. Incorrect tyre pres-
sure causes premature wear and could cause tyre blow-out.The pressure should therefore be checked at least once a month and before
starting a journey.
As a general rule, the pressures given are for cold tyres. When the tyres are
hot, the pressures are greater.
Never deflate a hot tyre in order to obtain the required pressure. This could
result in very low tyre pressures which may lead to sudden blow-outs.
Checking tyre pressures
Tyre pressures should only be checked when the vehicle has not been driven
for more than a few kilometres (miles) at low speeds in the past three hours.
xThe tyre pressures should be checked regularly, and only when the tyres
are cold. Always check all the tyres. Tyre pressures should be checked more
often in colder regions, and only when the vehicle has not been driven
recently. Always use a correctly-operating tyre gauge.
xAdjust tyre pressures to the loads carried in the vehicle.
xAfter checking the pressure, always replace the valve caps, and where
applicable, observe the instructions given for adjusting the tyre control
system Ÿpage 245.
WARNING
If tyre pressures are too high or too low, the tyre may deflate or burst
suddenly while driving. This could result in serious accident.
xIf the tyre pressure is too low, the tyres could overheat, resulting in
tread detachment or even burst tyres.
xWhen driving at high speeds and/or fully loaded, the tyre could
suddenly overheat, burst or be subject to tread detachment, with the
resultant loss of control of the vehicle.
xTyre pressures which are too high or too low reduce the service life of
the tyre, affecting the vehicle's performance.
xTyre pressures should be checked regularly, at least once a month and
before long journeys.

Wheels and tyres329
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xAdjust the pressures of all the tyres to the vehicle load.
xNever deflate excess pressure from hot tyres.
Caution
xTake care not to tilt the manometer when placing it on the valve. Other-
wise, the valve may be damaged.
xTo avoid damage to the valves, always replace valve caps correctly. Check
that the caps are identical to the standard caps and have been correctly tight-
ened.
For the sake of the environment
Under-inflated tyres will increase the fuel consumption.
Note
When checking tyre pressures, please observe the instructions for the tyre
control system Ÿpage 245.
Tread depth and wear indicators
Tread depth
Certain driving conditions require a deeper tread, as well as needing the tread
to be approximately the same on the front and rear tyres. This is particularly
important when driving in winter, in cold temperatures and on wet roads
Ÿ.
The minimum tread depth required by law in the majority of cases is 1.6 mm
(1/16 of an inch), measured in the tread grooves next to the tread wear indi-
cators. Observe legal requirements in each country.
The performance of winter tyres is much reduced when the tread has worn to
4 mm (5/32 inch).
The tread depth of new tyres may vary, according to the type and make of tyre
and the tread pattern.
Wear indicators on the tyre
The original tyres on your vehicle have 1.6 mm (1/16 inch) high Ÿfig. 184
tread wear indicators running across the tread. A number of these indicators
WARNING (continued)
Fig. 184 Tyre tread: tread
wear indicators.

If and when373
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a The vehicles should not touch. Otherwise, current may be allowed to flow
when the positive poles are connected.
Connect the clamps so they have good metal-to-metal contact with the termi-
nals.
If the engine fails to start straight-away, switch off the starter after about 10
seconds and try again after about a minute.
Complete operations only in the sequence given.
Jump lead terminal connections
xSwitch off the ignition of both vehicles Ÿpage 195.
xLikewise, open the battery cover in the engine compartment Ÿpage 318,
or remove the positive pole cap from one side 3), in the direction of the arrow
Ÿpage 372, fig. 225.
xConnect one end of the red jump lead to the positive terminal
Ÿpage 372, fig. 226 or Ÿpage 372, fig. 225 of the vehicle with the
flat battery Ÿ.
xConnect the other end of the red jump lead to the positive terminal in
the vehicle providing assistance .
xFor vehicles without Start-Stop system: Connect one end of the black
jump lead to the negative terminal in the vehicle providing assistance
Ÿpage 372, fig. 226.
xFor vehicles with Start-Stop system: Connect one end of the black
jump lead to a suitable ground connection, a solid piece of metal in the
engine block, or to the engine block Ÿpage 372, fig. 227.
xConnect the other end of the black jump lead to a solid metal compo-
nent connected to the engine block, or onto the engine block itself of the
vehicle with the flat battery however, connect it as far away as possible from
the battery Ÿ.
xPlace the leads so that they cannot be caught by any moving parts in the
engine compartment.Switching on
xStart the engine of the vehicle supplying current and let it run at idling
speed.
xStart the engine of the car with the flat battery and wait two or three
minutes until the engine is “running smoothly”.
Removing the jump leads
xBefore you remove the jump leads, switch off the headlights (if they are
switched on).
xTurn on the heating and rear window heater in the vehicle with the flat
battery. This helps minimise voltage peaks which are generated when the
leads are disconnected.
xWith the engines running, disconnect the leads in reverse order to
connection.
xClose the battery cover, or replace the positive pole cap 3).
WARNING
Incorrectly jump starting could cause the battery to explode resulting in
serious injury. Please observe the following rules to minimise the risk of a
battery explosion:
xAll work involving the vehicle battery and electrical system can cause
corrosion, fire and serious electric shocks. Always read and take into
account the safety warnings and standards before beginning work on the
battery Ÿpage 318, “Vehicle battery”.
xAlways protect your eyes with suitable working goggles and never lean
over the vehicle battery.
xThe jump leads must be connected in the correct order: first the positive
cable, then the negative cable.
xDo not attach the negative cable to parts of the fuel system or to the
brake hose/pipe.
3)Vehicles whose battery is not located in the engine compartment Ÿpage 372.
A+A+AA
A+AB
A-AB
AX
AX
AA

General notes on the technical data381
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Data on fuel consumption
Fuel consumption
The consumption and emission details shown on the vehicle
data sticker differ from one vehicle to another.
The fuel consumption, CO2 emissions and actual kerb weight of the vehicle
are noted on the vehicle data sticker.
The fuel consumption and emissions figures given are based on the vehicle
weight category, which is determined according to the engine/gearbox
combination and the equipment fitted.
The consumption and emission figures are calculated in accordance with the
EC test requirements 1999/100/EC. These test requirements specify a real-
istic test method based on normal everyday driving.
The following test conditions are applied:
Note
xActual consumption may vary from quoted test values, depending on
personal driving style, road and traffic conditions, the weather and the
vehicle condition.
Weights
Kerb weight refers to the basic model with a fuel tank filled to 90% capacity
and without optional extras. The figure quoted includes 75 kg to allow for the
weight of the driver.
For special versions and optional equipment fittings or for the addition of
accessories, the weight of the vehicle will increase Ÿ.
WARNING
xPlease note that the centre of gravity may shift when transporting
heavy objects; this may affect the vehicle's handling and lead to an acci-
dent. Always adjust your speed and driving style to suit road conditions
and requirements.
xNever exceed the gross axle weight rating or the gross vehicle weight
rating. If the allowed axle load or the allowed total weight is exceeded, the
driving characteristics of the vehicle may change, leading to accidents,
injuries and damage to the vehicle.
Urban cycleThe urban cycle starts with an engine cold start. City driving
is then simulated.
Extra urban
cycleIn the extra urban cycle simulation the vehicle frequently
accelerates and brakes in all gears, as in normal everyday
driving. The road speed ranges from 0 to 120 km/h.
Total con-
sumptionThe average total consumption is calculated with a weighting
of around 37% for the urban cycle and 63% for the extra
urban cycle.
CO2 emis-
sionsThe exhaust gases are collected during both driving cycles to
calculate carbon dioxide emissions. The gas composition is
then analysed to evaluate the CO
2 content and other emis-
sions.

Technical Data 384
Petrol engine 1.4 110 kW (150 PS)
Engine specifications
Performance figures
Consumption (litres/100 km)/ CO
2 (g/km)
WeightsPower output in kW (PS) rpm 110 (150)/ 5800
Maximum torque in Nm at rpm 240/ 1500-4000
No. of cylinders/ capacity
in cm
34/ 1390
Fuel
95 super RON
a)
a)Research-Octane-Number = Anti-detonation rating of the petrol.
Maximum speed in km/h 197
Acceleration from 0-80 km/h in sec. 6,9
Acceleration from 0-100 km/h in sec. 10,7
Urban cycle9,2/214
Extra urban cycle 6,1/143
Combined7,2/167
5 seats 7 seats
Gross vehicle weight in kg 2290 2480
Weight in running order (with driver) in kg 1723 1771
Gross front axle weight in kg 1170/1220 1170/1220
Gross rear axle weight in kg 1070/1120 1260/1310
Permitted roof load in kg 100 100