2010 Seat Alhambra check engine

Unlocking and locking95
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Rollback anti-trap function of the electric sliding doors
The rollback anti-trap function of the electric sliding doors can reduce the risk
of injury when opening and closing the sliding doors Ÿ.
If an object gets in the way of the sliding door while it is closing, it opens
again.
If an object gets in the way of the sliding door while it is opening, the door
stops moving.
xCheck the reason for which the sliding door does not open or close.
xTry to open or close the sliding door again.
To close the sliding door without the rollback anti-trap function
xTurn off the ignition and turn it on again.
xPress and hold the Ÿpage 94, fig. 54 button. The sliding door
closes with full force.
WARNING
Closing the electric windows without the anti-trap function can cause
serious injury.
xAlways close the sliding doors carefully.
xNobody should ever get in the way of the electric sliding doors, espe-
cially when closing without the anti-trap function.
xThe anti-trap function does not prevent fingers or other parts of the
body getting pinched against the window frame and causing injury.
Electric child safety lock
The electric child safety lock avoids opening and locking of the sliding door
and its electric windows from the inside so that children cannot accidentally
open the door while the vehicle is being driven. Using the left-hand side
Ÿfig. 55 or right-hand side button, the child safety lock is activated
on the left hand side or right-hand side respectively.
Turning on and off the electric child safety
The yellow indicator
r indicates that the function is on for the corresponding
button.
In the menu Configuration - Convenience the electric child safety function can
be configured to turn on automatically when the engine starts Ÿpage 70.
¼
FunctionNecessary operations
To switch system on:Press the button Ÿfig. 55 o .
The system switches
off:Press the button again.
Fig. 55 In the driver door:
electric child safety locks
buttons.
A1A2
A1A2

Unlocking and locking111
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xSearch the manufacturer's instructions manual for the garage door or
gate to find the “setting button” for the power motor to synchronise a new
remote control.
xAfter pressing the “settings button” on the power motor, you have a
maximum of 30 seconds to press the button , or . Press the same
button once more to complete the process. For some systems, the button
must be pressed the third time.
Erasing the programming for all buttons
SEAT recommends erasing the programming for all buttons when selling or
loaning your vehicle.
xBefore programming, carry out the initial steps Ÿpage 110.
xPress the buttons and until the indicator above the button begins
to blink.
xRelease both buttons. All of the programmed functions are erased.
After programming
Check the garage door remote control Ÿpage 111, “Using the garage door
remote control”.
Using the garage door remote control
The vehicle must be within range of the garage door or gate power motor.
xWith the engine running or the ignition on, push the corresponding
button on the sunshade Ÿ.
WARNING
Careless use of the garage remote control can cause serious injury.
xOnly use the remote control when you can see the garage door and that
there is nobody in its way.
Caution
Use of inappropriate batteries may damage the remote control. For this
reason, always replace the dead battery with another of the same voltage,
size and specifications.
For the sake of the environment
Please dispose of your used batteries correctly and with the utmost respect
for the environment.
123
132
FaultPossible causePossible solution
Garage door or
electric system is
not working.
The batteries of
remote control are
flat.Change the batteries.
The remote control is
too far away or the
transmission angle
was to large.Vary the distance and the angle
to the receiver.
The garage door or
electric system are
not compatible.The system does not corre-
spond to legal requirements
and must be replaced.
Programming was
not completed cor-
rectly.Program the remote control
once more.

Lights and visibility 124
Windscreen wiper and washer
Introduction
Additional information and warnings:
xRecirculation of air conditioning air Ÿpage 179
xWorking in the engine compartment Ÿpage 304
xCaring for and cleaning the vehicle exterior Ÿpage 269
WARNING
Water from the windscreen washer water bottle may freeze on the wind-
screen if it does not contain enough anti-freeze, reducing forward visibility.
xIn winter, ensure the windscreen washer contains enough anti-freeze.
xIn cold conditions, you should not use the wash / wipe system unless
you have warmed the windscreen with the ventilation system. The anti-
freeze could freeze on the windscreen and reduce visibility.
WARNING
Worn or dirty wiper blades reduce visibility and increase the risk of acci-
dent and serious injury.
xAlways replace damaged or worn blades or blades which do not clean
the windscreen correctly.
Caution
In icy conditions, always check that the wiper blades are not frozen to the
glass before using the wipers for the first time. In cold weather, it may help to
leave the vehicle parked with the wipers in service position Ÿpage 127.
Warning lamp
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
lights upPossible causeSolution
YWindscreen wiper fluid level
too lowTop up the windscreen wiper
bottle as soon as possible
Ÿpage 129.

Lights and visibility129
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Note
Clean the sensitive surface of the rain sensor regularly and check the blades
for damage Ÿpage 128, fig. 76 (arrow).
Note
To remove wax and coatings, we recommend a window cleaner containing
alcohol.
Checking and topping up the windscreen washer bottle with
water
Check the water level in the windscreen washer bottle regularly and top up as
required.
xOpen the bonnet ’ Ÿpage 304.
xThe washer bottle is marked with the symbol Y on the lid Ÿfig. 77.
xCheck there is enough water in the bottle.
xTo top up, mix water with a window cleaner recommended by SEAT Ÿ.
Please follow the instructions for use found on the packaging.
xIn cold weather, a special antifreeze should also be added to prevent the
water from freezing Ÿ.
Bottle capacity
The bottle holds approximately 3.0 litres; in vehicles with headlight washer,
it is approximately 7.0 litres.
WARNING
Never mix an unsuitable antifreeze or other similar products with the wind-
screen washer water. A greasy layer may be formed on the windscreen
which will impair visibility.
xUse clean water with a window cleaner recommended by SEAT.
xIf necessary, add a suitable antifreeze to the water bottle.
Caution
xDo not mix cleaning products recommended by SEAT with other products.
This could lead to flocculation and may block the windscreen washer jets.
xWhen topping up service fluids, make absolutely certain that you fill the
fluids into the correct reservoirs. Failure to observe this point will result in
serious malfunctions and engine damage!
Fig. 77 In the engine
compartment: windscreen
washer bottle top.

Heating, Ventilation and Air conditioning179
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Heating, Ventilation and Air conditioning
Climate Control
Introduction
Viewing Climatronic information
The factory-fitted radio or navigation system screen briefly displays informa-
tion relating to Climatronic.
The units of temperature measurement is displayed on the factory-installed
radio or navigation system and, depending on the vehicle equipment, can be
set using the Configuration menu on the instrument panel.
Additional information and warnings:
xSEAT information system Ÿpage 70
xWindscreen wash system Ÿpage 124
xAuxiliary heating Ÿpage 187
xCaring for and cleaning the vehicle exterior Ÿpage 269
WARNING
Reduced visibility through the windows increases the risk of serious acci-
dents.
xEnsure that all windows are free of ice and snow and that they are not
fogged up preventing a clear view of everything outside.
xThe maximum heat output required to defrost windows quickly is only
available when the engine has reached its normal running temperature.
Only drive when you have good visibility.
xAlways ensure that you use the climate control and heated rear window
to maintain good visibility.
xNever leave the air recirculation on for a long period of time. If the
cooling mode is switched off and air recirculation mode switched on, the
windows can mist over very quickly, considerably limiting visibility.
xSwitch air recirculation mode off when it is not required.
WARNING
Stuffy or used air will increase fatigue and reduce driver concentration
possibly resulting in a serious accident.
xNever leave the fresh air fan turned off or use the air recirculation for
long periods of time; the air inside the passenger compartment will not be
refreshed.
Caution
xSwitch the climate control system off if you think it may be broken. This
will avoid additional damage. Have the climate control system checked by a
qualified workshop.
xRepairs to the climate control system require specialist knowledge and
special tools. SEAT recommends visiting a qualified workshop.
xDo not smoke when air recirculation is switched on in vehicles with a
climate control system. The smoke taken in could lie on the cooling system
vaporiser and on the activated charcoal cartridge of the dust and pollen filter,
leading to a permanently unpleasant smell.
Note
When the cooling system is turned off, air coming from the outside will not be
dried. To avoid fogging up the windows, SEAT recommends leaving the cooler
WARNING (continued)

Heating, Ventilation and Air conditioning 184
Switching the Climatronic temperature measuring unit
Press and hold the and buttons to switch the temperature display
between Celsius and Fahrenheit.
Heat
The maximum heat output required to defrost windows quickly is only avail-
able when the engine has reached its normal running temperature.
The air conditioning system does not switch on
If the air conditioning system cannot be switched on, this may be caused by
the following:
xThe engine is not running.
xThe fan is switched off.
xThe climate control fuse has blown.
xThe outside temperature is lower than approximately +3 °C (+38 °F).
xThe climate control system compressor has been temporarily switched off
because the engine coolant temperature is too high.
xAnother fault in the vehicle. Have the climate control system checked by
a qualified workshop.
Things to note
If the humidity and temperature outside the vehicle are high, condensation
can drip off the evaporator in the cooling system and form a pool underneath
the vehicle. This is normal and does not indicate a leak!
Dust and pollen filter
The dust and pollen filter with its activated charcoal cartridge serves as a
barrier against impurities in the ambient air.
For the climate control system to work with maximum efficiency, the dust and
pollen filter must be replaced at the intervals specified in the Maintenance
Programme.If the filter loses efficiency prematurely due to use in areas with very high
levels of air pollution, the filter must be changed more frequently than stated
in the Service Schedule.
Note
The climate control system must left running for a few minutes to reach the
set temperature in the vehicle interior.
Note
After starting it, any residual humidity in the climate control system could
mist over the windscreen.
Note
The air from the vents flows through the passenger compartment and out
through the outlets below the rear window. Do not cover these outlets with
items of clothing or other objects.
ACAUTO

Heating, Ventilation and Air conditioning 190
Checking programming
If the timer has been switched on after switching the ignition off, the instant
on button will remain lit for around ten seconds.
WARNING
Never program the independent heating system to be activated and oper-
ated in closed, unventilated areas. The auxiliary heater fumes contain carbon dioxide, an odourless and colourless toxic gas. Carbon monoxide
can cause people to lose consciousness. It can also cause death.
User instructions
The auxiliary heater exhaust system located below the vehicle must be kept
clear of snow, mud and other objects. The exhaust fumes must not be
obstructed in any way. The exhaust fumes generated by the auxiliary heater
are removed via an exhaust pipe fitted underneath the vehicle.
On heating the vehicle interior, depending on the outside temperature the
warm air is first directed at the windscreen and then to the rest of the
passenger compartment through the air vents. If the air vents are turned
towards the windows, for example, the form of air distribution may be
affected.
Depending on the outside temperature, the temperature at which the auxil-
iary heater warms the vehicle interior may be somewhat higher if the heating
or climate control temperature control is set to maximum before switching the
heating on.
Depending on the engine, vehicles with auxiliary heater may be fitted with a
second battery in the luggage compartment that is responsible for powering
the auxiliary heater.
Cases in which the auxiliary heater will not switch on
xThe auxiliary heater requires about as much power as the dipped head-
lights. If the battery charge is low, the auxiliary heater will switch off automat-
ically or will not even switch on. This avoids problems when starting the
engine.
xThe heater will switch just once each time. The timer will also have to be
switched back on every time it is required.
Menu optionsDescription
Switching on
Switching off
The auxiliary heater can be set to come on automatically if
required. To do so, select a timer:
– The timer is displayed marked with a
y.
– Only one timer can be selected. If a timer has been
selected, Prog. ON will be displayed on the screen. If no
timer has been selected, the instrument panel screen will
display Prog. OFF.
– To modify the programmed timer, select another timer or
select the Off option.
Timer 1
Timer 2
Timer 3Three different timers (hh.mm) can later be selected using
the On option. If the auxiliary heater is to be switched on
for just a certain day of the week, select the day of the
week and the time for the auxiliary heater to come on.
DurationThe operating time may vary between 10 and 60 minutes
and can be set to 5-minute intervals.
Operating
modeSet to heat or ventilate the vehicle interior when the auxil-
iary heater is switched on.
DaySet the current day of the week.
Manufacturer's
settingsThe predefined factory values for the functions of this
menu are restored.
BackThis returns to the main menu
>
WARNING (continued)

Driving 192
Driving
Steering
Introduction
The power steering is not hydraulic but electromechanical. The advantage of
this steering system is that it disposes of hydraulic tubes, hydraulic oil, the
pump, filter and other components. The electromechanical system saves
fuel. While a hydraulic system requires oil pressure to be maintained, electro-
mechanical steering only requires energy when the steering wheel is turned.
With the power steering system, the assisted steering function automatically
adjusts according to the vehicle speed, the steering torque and the wheel
turning angle. The power steering only works when the engine is running.
Additional information and warnings:
xStart and stop the engine Ÿpage 195
xVehicle battery Ÿpage 318
xTow-starting and towing away Ÿpage 375
WARNING
If the power steering is not working then the steering wheel is much more
difficult to turn and the vehicle more difficult to control.
xThe power steering only works when the engine is running.
xNever allow the vehicle to move when the engine is switched off.
xNever remove the key from the ignition if the vehicle is in motion. The
steering may lock and it will not be possible to turn the steering wheel.
Control and warning lamps
lights upPossible causeSolution
D (red)Power steering faulty.The steering system should be
checked by a qualified workshop
as soon as possible.
D (yel-
low)
Power steering operation
reduced.
The steering system should be
checked by a qualified workshop
as soon as possible.
If, after restarting the engine and
driving for a short distance, the
yellow warning light no longer
comes on, it will not be neces-
sary to take the vehicle to a spe-
cialised workshop.
The vehicle battery was dis-
connected and has been
reconnected.Drive for a short distance at 15 –
20 km/h.