2010 PONTIAC G6 trunk

4. Remove the two nuts that hold the taillamp
assembly.
5. Remove the taillamp assembly.
6. Turn the bulb socket counterclockwise to remove.
7. Pull the bulb straight out of the socket.
8. Push the new bulb straight in until it clicks.
9. Turn the bulb socket clockwise to reinstall.
10. Reinstall the taillamp assembly and the two nuts
that hold the taillamp assembly.
11. Reinstall the wing nuts holding the trunk trim.
Taillamps, Turn Signal, Sidemarker,
Stoplamps and Back-up Lamps
(Coupe)
A. Sidemarker Lamp
B. Stoplamp/Taillamp/Turn Signal Lamp
C. Back-up Lamp
6-51

To replace one of these bulbs:
1. Open the trunk. SeeTrunk on page 3-11.
2. Remove the convenience net.
3. Remove the two wing nuts from the trunk trim and
pull back the trunk trim to expose the hex nuts.4. Remove the three hex nuts retaining the taillamp
assembly.
5. Pull the assembly off to the side to release it from
the rear of the vehicle.
6. Turn the bulb socket counterclockwise to remove
from the taillamp assembly.
7. Pull the bulb from the socket.
8. Push the new bulb into the socket until it clicks.
9. Turn the bulb socket clockwise to reinstall into the
taillamp assembly.
10. Push the taillamp assembly back into the rear of
the vehicle.
11. Reinstall the three hex nuts retaining the taillamp
assembly.
12. Reinstall the trunk trim and the two wing nuts.
6-52

Taillamps, Turn Signal, Sidemarker,
Stoplamps and Back-up Lamps
(Retractable Hardtop)
A. Sidemarker Lamp
B. Stoplamp/Taillamp/Turn Signal Lamp
C. Back-up LampTo replace one of these bulbs:
1. Open the trunk. SeeTrunk on page 3-11.
2. Locate the three rubber covers in the trunk trim,
near the taillamp assembly and remove them.
3. Remove the two nuts and one bolt retaining the
taillamp assembly.
4. Pull off the taillamp assembly to the side to release
it from the vehicle.
5. Turn the bulb socket counterclockwise to remove.
6. Pull the bulb from the bulb socket.
7. Push the new bulb straight in until it clicks.
8. Turn the bulb socket clockwise to reinstall.
9. Push the taillamp assembly back into place.
10. Reinstall the two nuts and one bolt retaining the
taillamp assembly.
11. Reinstall the trunk trim and three rubber covers.
6-53

Removal and Installation of the Sealant
Canister
To remove the sealant canister:
1. Remove the plastic cover.
2. Unscrew the connector (B) from the canister (A).
3. Pull up on the canister (A) to remove it.
4. Replace with a new canister which is available from
your dealer/retailer.
5. Push the new canister into place.
6. Screw the connector (B) to the canister (A).
7. Slide the plastic cover back on.
Tire Sealant and Compressor Kit
Storage
The tire sealant and compressor kit is located in the
trunk.
1. Open the trunk. SeeTrunk on page 3-11.
2. Lift the cover.
3. Turn the retainer clockwise and remove the tire
sealant and compressor kit.
To store the tire sealant and compressor kit, reverse the
steps.
6-89

A. Wheel Block
B. Flat Tire
The following information explains how to use the jack
and change a tire.
Removing the Spare Tire and Tools
The equipment you will need is located in the trunk.
1. If you have a retractable hardtop model, make sure
the hardtop is in the up position.
2. Open the trunk. SeeTrunk on page 3-11for more
information.3. If you have a sedan or coupe model, remove the
spare tire cover.
If you have a retractable hardtop model, unlatch the
trunk cargo cover so that it is in the open position.
Then remove the cover from the spare tire.
4. Turn the wing nut counterclockwise and remove it.
Then remove the compact spare tire. SeeCompact
Spare Tire on page 6-106for more information.
5. Remove the wing nut holding the jack in place.
6. Remove the extension bolt that is clipped to
the jack. You will need this later to store the flat tire.
7. Remove the jack and wheel wrench from the trunk.
6-91

3. Extend the handle on the wheel wrench by pressing
the button with your index finger and pulling on the
end of the wrench. You must do this before
using the wheel wrench.
Removing the Flat Tire and
Installing the Spare Tire
1. It is recommended a safety check is done before
proceeding. SeeChanging a Flat Tire on page 6-90
for more information.
2. If your vehicle has a wheel cover or hubcap that
has plastic wheel nut caps, then loosen the plastic
nut caps. You may need to use the wheel wrench
to loosen them. Do not pry off wheel covers or
center caps that have plastic wheel nut caps.
3. Remove the wheel cover or center cap from the
wheel to locate the wheel nuts.
If your vehicle has a wheel cover or hubcap without
plastic wheel nut caps, gently pry on the edge of
the plastic wheel trim to remove it from the wheel
to find the wheel nuts.
Store the wheel cover in the trunk until the flat is
repaired or replaced.
6-93

Storing a Flat or Spare Tire and
Tools
Storing a Flat Tire and Tools — All
Models Except GXP and Retractable
Hardtop
{WARNING:
Storing a jack, a tire, or other equipment in the
passenger compartment of the vehicle could
cause injury. In a sudden stop or collision, loose
equipment could strike someone. Store all these
in the proper place.
To store the flat tire and jack in the compact spare tire
compartment:
1. Open the trunk. SeeTrunk on page 3-11.
2. Remove the bolt extension (in the yellow sleeve)
from the jack and remove the center cap from the
wheel.3. Collapse the wrench using the same button used to
extend it.
4. Attach the wrench to the jack by placing the tab on
the wrench into the hole on the side of the jack.
Then place the wrench handle over the tab on the
side of the jack.
6-99

A. Cover
B. Wing Nut
C. Extension
D. Flat Tire (valve stem up)
E. Nut
F. Jack
G. Bolt
The compact spare is for temporary use only. Replace
the compact spare tire with a full-size tire as soon
as you can. SeeCompact Spare Tire on page 6-106.
Storing a Flat Tire and
Tools — GXP and Retractable
Hardtop Models
To store the flat tire and jack in the compact spare tire
compartment:
1. Make sure the retractable hardtop is in the up
position.
2. Open the trunk. SeeTrunk on page 3-11.
3. If you have a retractable hardtop model, unlatch the
trunk cargo cover so that it is in the open position.
4. Remove the bolt extension (in the yellow sleeve)
from the jack and remove the center cap from the
wheel.
6-101