2010 Peugeot 407 Dag ignition
[x] Cancel search: ignitionPage 67 of 249
4ACCESS
62
Using the remote control
Pressing button B locks the vehicle
(the direction indicators come on
for approximately two seconds).
A s e c o n d p r e s s w i t h i n fi v e s e c o n d s
deadlocks the vehicle (the direc-
tion indicators come on for approx-
imately two seconds).
LOCKING/UNLOCKING FROM THE INSIDE
MANUAL LOCKING (EMERGENCY MODE)
Automatic central locking of
the doors
The doors can lock automatically
while driving (speed above 6 mph
[10 km/h]).
Press and hold the button to activate
or deactivate this function. Key in ignition
A buzzer sounds on opening the dri-
ver's door, if the key has been left in
the ignition.
LOCATING YOUR VEHICLE
To locate your vehicle, if you have
locked or deadlocked it, in a car park:
press button B on the remote con-
trol, the courtesy lamps come on
a n d t h e d i r e c t i o n i n d i c a t o r s fl a s h
for a few seconds.
Note: driving with the doors
locked may make access to
the passenger compartment by
the emergency services more
d i f fi c u l t i n a n e m e r g e n c y .
If the vehicle is deadlocked,
the button is not active. In this
case, use the key or the re-
mote control to unlock.
Press the button.
This allows the doors and the boot to
be locked or unlocked. Driver's door
Insert the key in the lock to lock or unlock
the door.
Passenger doors
To lock, insert the key in the control
located on the edge of the door then
turn to the right.
Page 68 of 249
4ACCESS
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the cas-
ing using a coin at the notch.
REINITIALISATION
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking but-
ton immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the ig-
nition lock. The remote control is
now working again.
If the remote control does not work
after the battery has been changed,
reinitialise the remote control.
ELECTRONIC ENGINE IMMOBILISER
Electronic engine immobiliser
indicator lamp
It is accompanied by a message on
the multi-function screen.
Your vehicle will not start.
Consult a PEUGEOT dealer.
This locks the engine control sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic chip
which has a special code. When the ig-
nition is switched on, the code must be
recognised for starting to be possible.
If the system does not function correct-
ly, the following indicator lamp comes on:
Remote control
The high frequency remote control is
a sensitive system; do not operate it
while it is in your pocket as there is a
possibility that it may unlock the vehi-
cle, without you being aware of it.
Do not repeatedly press the buttons of
your remote control out of range and
out of sight of your vehicle. You run the
risk of stopping it from working and the
remote control would have to be reini-
tialised.
The remote control does not operate
when the key is in the ignition, even
when the ignition is switched off, ex-
cept for reinitialisation.
Locking the vehicle
Driving with the doors locked may
make access to the passenger com-
partment by the emergency services
m o r e d i f fi c u l t i n a n e m e r g e n c y .
As a safety precaution (with children
on board), remove the key from the
ignition when you leave the vehicle,
even for a short time. Lost keys
Visit a PEUGEOT dealer with
the vehicle's V5 registration
d o c u m e n t a n d y o u r p e r s o n a l i d e n t i fi -
cation documents.
The PEUGEOT dealer will be able to
retrieve the key code and the tran-
sponder code required to order a re-
placement key.
Page 69 of 249
4ACCESS
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the cas-
ing using a coin at the notch.
REINITIALISATION
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking but-
ton immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the ig-
nition lock. The remote control is
now working again.
If the remote control does not work
after the battery has been changed,
reinitialise the remote control.
ELECTRONIC ENGINE IMMOBILISER
Electronic engine immobiliser
indicator lamp
It is accompanied by a message on
the multi-function screen.
Your vehicle will not start.
Consult a PEUGEOT dealer.
This locks the engine control sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic chip
which has a special code. When the ig-
nition is switched on, the code must be
recognised for starting to be possible.
If the system does not function correct-
ly, the following indicator lamp comes on:
Remote control
The high frequency remote control is
a sensitive system; do not operate it
while it is in your pocket as there is a
possibility that it may unlock the vehi-
cle, without you being aware of it.
Do not repeatedly press the buttons of
your remote control out of range and
out of sight of your vehicle. You run the
risk of stopping it from working and the
remote control would have to be reini-
tialised.
The remote control does not operate
when the key is in the ignition, even
when the ignition is switched off, ex-
cept for reinitialisation.
Locking the vehicle
Driving with the doors locked may
make access to the passenger com-
partment by the emergency services
m o r e d i f fi c u l t i n a n e m e r g e n c y .
As a safety precaution (with children
on board), remove the key from the
ignition when you leave the vehicle,
even for a short time. Lost keys
Visit a PEUGEOT dealer with
the vehicle's V5 registration
d o c u m e n t a n d y o u r p e r s o n a l i d e n t i fi -
cation documents.
The PEUGEOT dealer will be able to
retrieve the key code and the tran-
sponder code required to order a re-
placement key.
Page 70 of 249
4ACCESS
64
Anti-theft protection
D o n o t m a k e a n y m o d i fi c a -
tions to the electronic engine
immobiliser system; this could
cause malfunctions. CHILD LOCK
Electric mode Always remove the ignition
key when leaving the vehicle,
even for a short time.
It is advisable to check the ac-
tivation of the child lock each time the
ignition is switched on.
In the event of a serious impact, the
electric child lock is deactivated auto-
matically to permit the exit of the rear
passengers.
This prevents opening of both of the
rear doors from the inside.
With the ignition on, press the button.
A message appears on the multifunc-
tion screen.
This system is independent and does
not take the place of the central lock-
ing control in any circumstances.
This prevents each of the rear doors
from being opened from inside.
Turn the switch on the edge of the
door a quarter of a turn using the
ignition key.
Manual mode
When purchasing a second-
hand vehicle
Have the key codes memorised by a
PEUGEOT dealer, to ensure that the
keys in your possession are the only
ones which can start the vehicle. Do not throw the remote con-
trol batteries away, they con-
tain metals which are harmful
to the environment.
Take them to an approved col-
lection point.
Page 71 of 249
4ACCESS
64
Anti-theft protection
D o n o t m a k e a n y m o d i fi c a -
tions to the electronic engine
immobiliser system; this could
cause malfunctions. CHILD LOCK
Electric mode Always remove the ignition
key when leaving the vehicle,
even for a short time.
It is advisable to check the ac-
tivation of the child lock each time the
ignition is switched on.
In the event of a serious impact, the
electric child lock is deactivated auto-
matically to permit the exit of the rear
passengers.
This prevents opening of both of the
rear doors from the inside.
With the ignition on, press the button.
A message appears on the multifunc-
tion screen.
This system is independent and does
not take the place of the central lock-
ing control in any circumstances.
This prevents each of the rear doors
from being opened from inside.
Turn the switch on the edge of the
door a quarter of a turn using the
ignition key.
Manual mode
When purchasing a second-
hand vehicle
Have the key codes memorised by a
PEUGEOT dealer, to ensure that the
keys in your possession are the only
ones which can start the vehicle. Do not throw the remote con-
trol batteries away, they con-
tain metals which are harmful
to the environment.
Take them to an approved col-
lection point.
Page 72 of 249
4ACCESS
65
ALARM
For all work on the alarm system, con-
tact a PEUGEOT dealer.
- Exterior perimeter
The system checks for opening of the
vehicle.
The alarm is triggered if anyone tries
to open a door, the boot, the bonnet...
- Interior volumetric
The system checks for any variation in
the volume in the passenger compart-
ment.
The alarm is triggered if anyone breaks
a window, enters the passenger com-
partment or moves inside the vehicle.
Self-protection function
The system checks for the
putting out of service of its
components.
The alarm is triggered if the battery, the
central control or the wires of the siren
are put out of service or damaged. Locking the vehicle with full
alarm system
Activation
Switch off the ignition and get out
of the vehicle.
Press the locking button on the re-
mote control.
The monitoring system is active: the
i n d i c a t o r l a m p o n t h e b u t t o n fl a s h e s
once per second.
After the locking button on the remote
control is pressed, the exterior perime-
ter monitoring is activated after a delay
of 5 seconds and the interior volumet-
ric after a delay of 45 seconds.
If an opening (door, boot...) is not
closed fully, the vehicle is not locked
but the exterior perimeter monitor-
ing will be activated after a delay of
45 seconds at the same time as the
interior volumetric monitoring.
System which protects and provides a
deterrent against theft and break-ins.
It provides the following types of moni-
toring.
Deactivation
Press the unlocking button on the
remote control.
The alarm system is deactivated: the in-
dicator lamp on the button switches off.
Locking the vehicle with
exterior perimeter monitoring
only
Deactivate the interior volumetric pro-
tection to avoid unwanted triggering of
the alarm in certain cases such as:
- leaving a pet in the vehicle,
- leaving a window partially open,
- washing your vehicle,
- changing a wheel,
- having your vehicle towed,
- transport by sea.
Deactivation of the interior
volumetric monitoring
Switch off the ignition.
Within ten seconds, press the but-
ton until the indicator lamp is lit
continuously.
Get out of the vehicle.
Press the locking button on the re-
mote control immediately.
The exterior perimeter monitoring alone
is activated: the indicator lamp on the
b u t t o n fl a s h e s o n c e p e r s e c o n d .
To be effective, this deactivation must
be carried out each time the ignition is
switched off.
Page 73 of 249
4ACCESS
66
Reactivation of the interior
volumetric monitoring
Press the unlocking button on the
remote control to deactivate the
exterior perimeter monitoring.
Press the locking button on the
remote control to activate all the
monitoring functions.
The indicator lamp on the button again
fl a s h e s o n c e p e r s e c o n d . Triggering of the alarm
This is indicated by sounding of the
s i r e n a n d fl a s h i n g o f t h e d i r e c t i o n i n d i -
cators for thirty seconds.
The monitoring functions remain ac-
tive until the alarm has been triggered
eleven times in succession.
When the vehicle is unlocked using
t h e r e m o t e c o n t r o l , r a p i d fl a s h i n g o f
the indicator lamp on the button in-
forms you that the alarm was triggered
during your absence. When the igni-
t i o n i s s w i t c h e d o n , t h i s fl a s h i n g s t o p s
immediately.
Failure of the remote control
To deactivate the monitoring functions:
Unlock the vehicle using the key in
the driver's door lock.
Open the door; the alarm is trig-
gered.
Switch on the ignition; the alarm
stops. The indicator lamp on the
button switches off. Locking the vehicle without
activating the alarm
Lock or deadlock the vehicle using
the key in the driver's door lock.
Malfunction
W h e n t h e i g n i t i o n i s s w i t c h e d o n , fi x e d
lighting of the indicator lamp on the
button indicates a malfunction of the
system.
Have it checked by a PEUGEOT dealer.
* According to country.
Automatic activation *
2 minutes after the last door or the
boot is closed, the system is activated
automatically.
To avoid triggering the alarm on
e n t e r i n g t h e v e h i c l e , fi r s t p r e s s t h e
unlocking button on the remote
control.
Page 74 of 249
4ACCESS
67
ELECTRIC WINDOWS
Automatic operation:
To open or close the window, press or
pull switch fully: the window opens or
closes completely when the switch is
released. Pressing the switch again
stops the movement of the window.
The electric window switches remain
operational for approximately one min-
ute after the key has been removed
from the ignition.
Once this time has elapsed, the elec-
tric windows will not operate. To re-
activate them, switch the ignition on
again.
Always remove the key from
the ignition when leaving the
vehicle, even for a short time.
In the event of contact during
operation of the windows, you must re-
verse the movement of the window. To
do this, press the switch concerned.
When the driver operates the passen-
ger electric window switches, he must
ensure that no one is preventing cor-
rect closing of the windows.
The driver must ensure that the pas-
sengers use the electric windows cor-
rectly.
Be aware of children when operating
the windows. REINITIALISATION OFTHE ELECTRIC WINDOWS
Following reconnection of the battery,
the safety anti-pinch function must be
reinitialised: the safety anti-pinch func-
tion is not active during these opera-
tions.
- lower the window completely, then raise it, it will rise in steps of a few
centimetres each time the switch is
pressed. Repeat the operation un-
til the window closes completely,
- continue to press the switch for at least one second after reaching
this position, window closed.
Safety anti-pinch
When the window rises and meets an
obstacle, it stops and immediately par-
tially lowers again.
In the event of unwanted opening
of the window on closing, press the
switch until the window opens com-
pletely, then pull the switch immediate-
ly until the window closes. Continue to
hold the switch for approximately one
second after the window has closed.
The safety anti-pinch function is not
active during this operation.
Deactivating the rear window
controls
For the safety of your children, press
switch 5 to prevent operation of the rear
windows irrespective of their position.
When the button is pressed down, the
switches are deactivated. When the but-
ton is raised, the switches are active.
Manual operation:
To open or close the window, press
or pull the switch gently. The win-
dow stops as soon as the switch is
released.
1. Driver's electric window switch.
2. Passenger's electric window
switch.
3. Rear right electric window
switch.
4. Rear left electric window
switch.
5. Deactivating the rear electric
window switches (child safety).