2010 Peugeot 407 Dag battery

4ACCESS
70
Notes:
After reconnecting the battery, you
must reinitialise the safety anti-pinch:
- place the control in the maximum partial opening position (3rd notch
to the right),
- wait until the roof is in the maxi- mum partially open position,
- press the control for at least one second.
In the event of unwanted opening of
the roof on closing (for example, in the
presence of ice), and immediately af-
ter the roof stops:
- move the control to the "O" posi- tion and press the control immedi-
ately,
- continue to press the control until the roof is fully closed. SUNROOF (SALOON) Always remove the key from
the ignition when leaving the
vehicle, even for a short time.
In the event of contact during
operation of the roof, you must reverse
the movement of the roof. To do this,
press the switch concerned.
When the driver operates the roof
switch, they must ensure that no one
is preventing correct closing of the
roof.
The driver must ensure that passen-
gers use the sunroof correctly.
Be aware of children when operating
the roof.
- To partially open the roof: Turn the switch to the right (three possible
settings).
- To open the roof completely: Turn the switch to the left (six possible
settings).
- To close it completely: Turn the switch back to position "O".
- Safety anti-pinch: When the sun- roof is closing and meets an ob-
stacle, it stops then partially opens
again.
The sunroof blind is manual.

4ACCESS
71
Safety anti-pinch
If the blind encounters an obstacle
during closing, it stops and partially
opens again.
You must reinitialise the safety anti-
pinch within a maximum of fi ve sec-
onds after the blind has stopped:
- press part A of the control until the
blind is completely closed (closing
in stages of a few centimetres). PANORAMIC SUNROOF (407SW) In the event of contact du-
ring operation of the blind, you
must reverse its movement.
To do this, press the control
concerned.
When the driver operates the blind-
control, they must ensure that no one
is preventing the blind from closing
correctly.
The driver must ensure that the pas-
sengers use the blind correctly.
Pay attention to children during opera-
tion of the blind.

Notes :
Following reconnection of the battery,
in the event of a blind malfunction
while it is moving or immediately after
it has stopped, you must reinitialise
the safety anti-pinch:
- place the control in the fully open position (position "0"),
- wait until the blind is in the fully open position,
- press section A of the control for at
least three seconds.
In the event of unwanted opening of
the blind on closing, and immediately
after the blind has stopped:
- move the control to the fully closed position (9th setting to the left) then
press part A of the control straight
away,
- continue to press the control until the blind is fully closed.

The safety anti-pinch function is not
active during these operations.
Your vehicle is fi tted with a tinted glass
panoramic sunroof which increases
the light and visibility in the passen-
ger compartment. Its electric blind im-
proves temperature conditions.

The blind is controlled electrically by
a dial with nine opening positions.

To close: turn the dial to the left (nine
possible settings).

To open: return the dial to the initial
position "0" .

9CHECKS
112
CHECKS
At the start of winter, have
your battery checked by a
PEUGEOT dealer.
Have the fi lter elements re-
placed regularly. If you drive
in dusty conditions, change
them twice as often.
Air filter and passenger
compartment filter
Particle emission filter (Diesel)
It is essential that the particle emission
fi lter is maintained in accordance with
the manufacturer's servicing schedule,
by a PEUGEOT dealer.

Note : following prolonged operation
of the vehicle at very low speed or at
idle, you may, in exceptional circum-
stances, notice emissions of water va-
pour at the exhaust on acceleration.
This does not have any effect on the
performance of the vehicle or the en-
vironment.
On vehicles which are fi tted with a par-
ticle emission fi lter, the cooling fan may
operate after the vehicle has stopped,
even when the engine is cold. Where the parking brake trav-
el is too great or there is a re-
duction in the performance of
the system, the parking brake
should be adjusted.
Have the system checked by a PEUGEOT
dealer.
Parking brake
Disc wear status
For any information relating to check-
ing disc wear, contact a PEUGEOT
dealer.
FUEL SUPPLY CUT-OFF (PETROL) *
As a safety precaution, in certain cir-
cumstances the fuel supply to the en-
gine is cut off.
To re-establish the fuel supply:
RUNNING OUT OF FUEL (DIESEL)
If you should run out of fuel, it is ne-
cessary to prime the fuel system.
The priming pump and the bleed screw
are located under the bonnet (see cor-
responding illustration in the technical
information section):
1.6 litre 16V HDI engine
- fi ll the fuel tank with at least fi ve li-
tres of diesel,
- squeeze and release the manual priming pump until fuel appears in
the transparent pipe,
- operate the starter until the engine starts.
2 litre 16V HDI engine
- fi ll the fuel tank with at least fi ve li- tres of diesel,
- unscrew the bleed screw,
- squeeze and release the manual priming pump until diesel is seen
escaping via the bleed screw,
- retighten the bleed screw,
- operate the starter until the engine starts.
Brake pad wear depends on
the style of driving, in particu-
lar for vehicles which are used
in town, over short distances.
Brake pads It may be necessary to check
the brake pads for wear, even
between services.
* According to version.
To ensure the best perfor-
mance from components as
important as the power steer-
ing and the braking system,
the manufacturer selects and offers
specifi c products, only use products
recommended by PEUGEOT.
Battery
To prevent damage to the electrical
units, high pressure washing of the en-
gine compartment is strictly prohibited .
 press the red button on the angle
of the front right-hand suspension
housing, under the bonnet.

1010PRACTICAL INFORMATION
123
The electrical system of your
vehicle is designed to oper-
ate with standard or optional
equipment.
Before installing other electrical equip-
ment or accessories on your vehicle,
contact a PEUGEOT dealer.
PEUGEOT will not accept responsi-
bility for the cost incurred in repairing
your vehicle or for rectifying the mal-
functions resulting from the installation
of accessories not supplied and not
recommended by PEUGEOT and not
installed in accordance with its instruc-
tions, in particular when the combined
consumption of all of the additional
equipment connected exceeds 10 mil-
liamperes.
The maxi-fuses provide additional
protection for the electrical systems.
All work must be carried out by a
PEUGEOT dealer. CHANGING A WINDSCREEN WIPER BLADE ECONOMY MODE FUNCTION
After the engine has stopped, certain
electrical functions can be used for a
maximum duration of approximately
one hour, to prevent discharging of the
battery.
A fl at battery prevents the en-
gine from starting.
If the telephone is being used
when economy mode starts,
it will still be possible to fi nish
the call.
Placing the wiper blades in
the maintenance position

 Less than one minute after swit-
ching off the ignition, press the
windscreen wiper stalk down once
to position the blades vertically on
the windscreen (maintenance po-
sition).
Replacing a blade

 Lift the arm, then unclip the blade
and remove it.

 Fit the new blade and fold down
the arm.
To reposition the blades, switch on the
ignition and operate the windscreen
wiper stalk. This period may be signifi -
cantly reduced if the battery
charge is low.
Once the hour is over, a message ap-
pears on the multi-function display
and the active functions are put on
standby.
These functions are automatically re-
activated when the vehicle is started.
As winter approaches, have your bat-
tery checked by a PEUGEOT dealer.

1010PRACTICAL INFORMATION
122
Engine compartment fuses
To access the fuses located in the
engine compartment (next to the bat-
tery), remove the battery cover and
unclip the fusebox cover.
Close the fusebox cover carefully and
refi t the battery cover when you have
fi nished.
Fuse N°
Rating

(A)
Functions

1 20 Engine management control unit.

2 15 Horn.

3 10 Front and rear wash-wipe.

4 20 Headlamp wash.

5 15 Engine management actuators (fuel pump,
purge canister electrovalves, ...).

6 10 Automatic gearbox control unit.

7 10 Switching and protection unit, intake air
fl ow sensor, clutch switch, six-speed
automatic gearbox switch, STOP switches,
electrochromatic mirror, panoramic sunroof blind
controls (407SW).

8 20 Starter coil.

9 10 Xenon bulb electronics supply, STOP switch,
power steering electropump, four-speed
automatic gearbox control unit, automatic
gearbox locking relay.

10 30 Engine management actuators (ignition coil,
electrovalves, oxygen sensors).

11 40 Air conditioning blower or not used.

12 30 Windscreen wipers.

13 40 Built-in systems interface supply (ignition
positive).

14 30 Air pump.

1010PRACTICAL INFORMATION
123
The electrical system of your
vehicle is designed to oper-
ate with standard or optional
equipment.
Before installing other electrical equip-
ment or accessories on your vehicle,
contact a PEUGEOT dealer.
PEUGEOT will not accept responsi-
bility for the cost incurred in repairing
your vehicle or for rectifying the mal-
functions resulting from the installation
of accessories not supplied and not
recommended by PEUGEOT and not
installed in accordance with its instruc-
tions, in particular when the combined
consumption of all of the additional
equipment connected exceeds 10 mil-
liamperes.
The maxi-fuses provide additional
protection for the electrical systems.
All work must be carried out by a
PEUGEOT dealer. CHANGING A WINDSCREEN WIPER BLADE ECONOMY MODE FUNCTION
After the engine has stopped, certain
electrical functions can be used for a
maximum duration of approximately
one hour, to prevent discharging of the
battery.
A fl at battery prevents the en-
gine from starting.
If the telephone is being used
when economy mode starts,
it will still be possible to fi nish
the call.
Placing the wiper blades in
the maintenance position

 Less than one minute after swit-
ching off the ignition, press the
windscreen wiper stalk down once
to position the blades vertically on
the windscreen (maintenance po-
sition).
Replacing a blade

 Lift the arm, then unclip the blade
and remove it.

 Fit the new blade and fold down
the arm.
To reposition the blades, switch on the
ignition and operate the windscreen
wiper stalk. This period may be signifi -
cantly reduced if the battery
charge is low.
Once the hour is over, a message ap-
pears on the multi-function display
and the active functions are put on
standby.
These functions are automatically re-
activated when the vehicle is started.
As winter approaches, have your bat-
tery checked by a PEUGEOT dealer.

1010PRACTICAL INFORMATION
123
The electrical system of your
vehicle is designed to oper-
ate with standard or optional
equipment.
Before installing other electrical equip-
ment or accessories on your vehicle,
contact a PEUGEOT dealer.
PEUGEOT will not accept responsi-
bility for the cost incurred in repairing
your vehicle or for rectifying the mal-
functions resulting from the installation
of accessories not supplied and not
recommended by PEUGEOT and not
installed in accordance with its instruc-
tions, in particular when the combined
consumption of all of the additional
equipment connected exceeds 10 mil-
liamperes.
The maxi-fuses provide additional
protection for the electrical systems.
All work must be carried out by a
PEUGEOT dealer. CHANGING A WINDSCREEN WIPER BLADE ECONOMY MODE FUNCTION
After the engine has stopped, certain
electrical functions can be used for a
maximum duration of approximately
one hour, to prevent discharging of the
battery.
A fl at battery prevents the en-
gine from starting.
If the telephone is being used
when economy mode starts,
it will still be possible to fi nish
the call.
Placing the wiper blades in
the maintenance position

 Less than one minute after swit-
ching off the ignition, press the
windscreen wiper stalk down once
to position the blades vertically on
the windscreen (maintenance po-
sition).
Replacing a blade

 Lift the arm, then unclip the blade
and remove it.

 Fit the new blade and fold down
the arm.
To reposition the blades, switch on the
ignition and operate the windscreen
wiper stalk. This period may be signifi -
cantly reduced if the battery
charge is low.
Once the hour is over, a message ap-
pears on the multi-function display
and the active functions are put on
standby.
These functions are automatically re-
activated when the vehicle is started.
As winter approaches, have your bat-
tery checked by a PEUGEOT dealer.

1010PRACTICAL INFORMATION
124
To start the vehicle from another
battery:
- Connect the red cable to the positive (+) terminals of the two batteries,
- Connect one end of the green or black cable to the negative (-) ter-
minal of the slave battery,
- Connect the other end of the green or black cable to an earth point on
the broken down vehicle as far as
possible from the battery,
- Operate the starter, let the engine run,
- Wait for the engine to return to idle, then disconnect the cables.
BATTERY (LOCATED IN THE ENGINE COMPARTMENT)
Disconnecting/Reconnecting
the cables

1. Raise the locking plate A .

2. Position the open clip of the cable
on the positive (+) terminal of the
battery.

3. Press until the position checking
system B tilts.

4. Lock the clip by lowering the lock-
ing plate while pressing on the
clip.
It is advisable to disconnect
the battery if the vehicle is not
to be used for a period of more
than one month.
To charge the battery using a
battery charger:
- Disconnect the battery,
- Follow the instructions for use giv-
en by the manufacturer the battery
charger,
- Reconnect starting with the nega- tive (-) terminal,
-
Check that the terminals and connec-
tors are clean. If they are covered with
sulphate (white or greenish deposit),
disconnect them and clean them.
Do not force the plate as lock-
ing is not possible if the clip is
not positioned correctly.
Start the procedure again.