2010 Peugeot 206 P Dag lock
[x] Cancel search: lockPage 5 of 107
19
Warning lamps
When the engine is running or the vehicle is being driven, the switching on of one of the following warning lamps indicates a
fault which requires action on the part of the driver.
Any fault resulting in the switching on of a warning lamp must be investigated further by reading the associated message on
the multifunction screen.
If you encounter any problems, do not hesitate to contact a PEUGEOT dealer.
Warning lamp is on Cause Action/Observations
STOP fi x e d ,
associated
with another
warning lamp. It is associated with the
braking, the engine oil pressure
or the coolant temperature.
Stop as soon as it is safe to do so.
Park, switch off the ignition and call a
PEUGEOT dealer.
Braking fi x e d .
T h e b r a k i n g s y s t e m fl u i d l e v e l
h a s d r o p p e d s i g n i fi c a n t l y . T o p u p w i t h b r a k e fl u i d r e c o m m e n d e d b y
PEUGEOT.
If the problem persists, have the system
checked by a PEUGEOT dealer.
+
fi x e d , a s s o c i a t e d with the ABS
warning lamp. The electronic brake force
distribution (EBFD) system has
a fault. Have it checked by a PEUGEOT dealer.
Anti-lock
Braking
System (ABS) fi x e d . The anti-lock braking system
has a fault. The vehicle retains conventional braking.
Drive carefully at reduced speed and contact
a PEUGEOT dealer without delay.
Dynamic
stability control
(ESP/ASR) fl a s h i n g .
The ESP/ASR regulation is
active. The system optimises traction and improves
the directional stability of the vehicle.
fi x e d . Unless it has been deactivated
with the indicator lamp on
the button on, the ESP/ASR
system is faulty. Have it checked by a PEUGEOT dealer.
Page 10 of 107
ii
ii
INSTRUMENTS and CONTROLS
24
Following this operation, if you
wish to disconnect the battery,
lock the vehicle and wait at least
fi v e m i n u t e s f o r t h e z e r o r e s e t t o b e
taken into account.
Service indicator zero reset
After each service, the service indicator
must be reset to zero.
The procedure for resetting to zero is as
follows:
switch off the ignition,
press and hold the trip distance re-
corder zero reset button,
switch on the ignition; the distance
recorder display begins a count-
down,
when the display indicates "=0" ,
release the button; the spanner
disappears.
The distance remaining may be
weighted by the time factor, depend-
ing on the driver's driving habits.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.
Service overdue
For 5 seconds after the ignition is
switched on,
t h e s p a n n e r fl a s h e s to
indicate that the service must be carried
out as soon as possible.
Example: the service is overdue by
300 miles/km.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched on,
the distance recorder resumes its normal
operation. The spanner remains lit .
Page 11 of 107
25
TOTAL DISTANCE RECORDER
System which measures the total dis-
tance travelled by the vehicle during its
life. LIGHTING RHEOSTAT
System for manual adjustment of the
brightness of the instrument panel in re-
lation to the exterior brightness.
The total and trip distances are dis-
played for thirty seconds when the ig-
nition is switched off, when the driver's
door is opened and when the vehicle is
locked or unlocked.
TRIP DISTANCE RECORDER
System which measures a distance
travelled during a day or other period
since it was reset to zero by the driver.
With the ignition on, press the but-
ton until zeros appear. Activation
When the exterior lighting is on:
press the button to change the
brightness of the instrument panel,
when the lighting reaches the mini-
mum setting, release the button,
then press again to increase it,
or
when the lighting reaches the maxi-
mum setting, release the button,
then press again to reduce it,
when the lighting reaches the level
of brightness required, release the
button.
Deactivation
When the exterior lighting off, pressing
the button does not have any effect.
Page 12 of 107
INSTRUMENTS and CONTROLS
26
MONOCHROME SCREEN A Adjusting the parameters
Press and hold button 1 for two seconds
t o a c c e s s t h e s e t t i n g s ; t h e d a t a fl a s h e s ,
i n d i c a t i n g i t i s r e a d y t o b e m o d i fi e d .
Then, each press of button 1 scrolls
through the various data in the following
order:
- language of information displayed,
- hours (12 then 24 hour mode),
- minutes,
- year,
- month,
- day,
- unit of temperature (degrees Celsius or Fahrenheit).
Pressing button 2 a l l o w s m o d i fi c a t i o n
of the data selected. Press and hold for
rapid advance (return to start after the
last possible value).
After 7 seconds with no action, the main
d i s p l a y r e t u r n s ; t h e m o d i fi e d d a t a a r e
now recorded.
Note: Pressing button 2 b r i e fl y d i s p l a y s
the ambient temperature for a few sec-
onds.
When the ambient temperature is be-
tween -3° and 3 °C, the ambient tem-
perature display on the screen takes
priority over the clock display.
This displays the following information:
- time,
- date,
- a m b i e n t t e m p e r a t u r e * ( t h i s fl a s h e s
when it is between -3 and 3 °C),
- audio system information,
- a door check (e.g.: ''left front door open''),
- warning messages (e.g. ''remote c o n t r o l b a t t e r y fl a t ' ' ) o r i n f o r m a t i o n
messages (e.g. ''economy mode
active''), displayed temporarily.
* With digital air conditioning only.
Page 24 of 107
!i
37
1 - F o r w a r d s - b a c k w a r d s a d j u s t m e n t
Lift the control and slide the seat for-
wards or backwards.
2 - Height adjustment
Pull the handle upwards.
Remove your weight from the seat to
raise, or press on the seat to lower.
3 - Access to the rear seats
(3-door), A or B according to model
A. P l a c e y o u r fi n g e r s i n o n e o f t h e t w o
handles and push forwards to fold
down the seat back and move the
seat forwards.
When put back, the seat returns to its initial position.
No person or object must prevent the seat from returning to its initial
position. Returning to this position is
necessary for the seat to lock. 4 - Seat back angle adjustment
Push the handle towards the rear.
5 - Head restraint height adjustment
To raise the head restraint, pull it up-
wards.
T h e a d j u s t m e n t i s c o r r e c t w h e n t h e
upper edge of the head restraint is
l e v e l w i t h t h e t o p o f t h e h e a d .
T h e h e a d r e s t r a i n t i s fi t t e d w i t h a f r a m e
with notches, which prevent the head
restraint dropping down (this is a safety
device in case of impact).
FRONT SEATS
Seat consisting of a seat cushion, seat
back and head restraint which can all
be adjusted to your optimum driving
and comfort position.
Never drive with the head re-
straints removed; they should be
in place and correctly adjusted.
It is impossible to access the rear
seats if the front seat is in a reclining
position.
Heated seats
Press the switch, located on the control
panel next to the steering wheel. The
temperature is regulated automatically.
Press again to switch off.
Rear head restraint
These have a position for use (high)
and a position for storage (low).
To lower the head restraints, press the lug.
They can also be removed.
To remove the head restraints, pull up-
wards as far as the stop then press the
release control.
To lower the head restraint, push simul-
taneously:
- the button on the left-hand guide at
the base of the head restraint frame,
- the head restraint downwards.
To remove the head restraint, press the lug.
B. P l a c e y o u r fi n g e r s i n o n e o f t h e t w o
handles and push forwards to fold
down the seat back. The seat does
not move forwards.
When put back, the seat back returns to its initial angle.
Page 25 of 107
!!
38
REAR SEATS
- position the seat belt under the belt holder 2 ,
- pull control 3 to unlock the seat
back 4 ,
- remove or lower the head restraint,
- tilt the seat back 4 . When repositioning:
- return the seat back to the upright
position,
- fold back the seat cushion,
- reposition the seat belt buckles before locking the front of the seat
cushion.
- check that the seats are locked cor- rectly.
Control 3 must be in the low position.
Rear seat or bench seat which can be
folded to adapt the load space in the
boot.
To fold the rear seats:
- lift the front of the seat cushion
1 ,
- tilt the seat cushion 1 against the
front seats,
Take care not to trap the seat
belts.
A l w a y s s t a r t w i t h t h e s e a t
cush-
ion
, never the seat back (risk of
damage).
Page 26 of 107
!!
39
BENCH SEAT
- position the seat belt under the belt holder 2 ,
- pull the controls 3 to unlock the seat
back 4 ,
- remove or lower the head re- straints,
- tilt the seat back 4 . When repositioning:
- return the seat back to the upright
position,
- fold back the seat cushion,
- reposition the seat belt buckles before locking the front of the seat
cushion.
- check that the bench seat is secured fi r m l y .
The controls 3 must be in the low
position.
To fold the bench seat:
- lift the front of the seat cushion
1 ,
- tilt the seat cushion 1 against the
front seats,
Take care not to trap the seat
belts.
A l w a y s s t a r t w i t h t h e s e a t
cush-
ion
, never the seat back (risk of
damage).
Page 29 of 107
!
42
STEERING WHEEL ADJUSTMENT
The height of the steering wheel can be
adjusted to adapt the driving position to
the size of the driver.
Adjustment
When stationary , lower the control
lever to unlock the steering wheel.
Adjust the height.
Raise the control lever to lock the
steering wheel.
As a safety precaution, these op-
erations must only be carried out
while the vehicle is stationary.
SUN VISOR
Component which protects against
sunlight from the front or the side, also
equipped with a courtesy mirror.
T h e s u n v i s o r s a r e fi t t e d w i t h a c o u r -
t e s y m i r r o r , w i t h c o n c e a l i n g fl a p f o r t h e
driver.
PORTABLE ASHTRAY
This can be placed at the front or at the
rear of the centre console.
Pull the cover to open the ashtray.
To empty it, remove the ashtray by
pulling it upwards.