2010 MITSUBISHI OUTLANDER remote control

3-66 Features and controls
3Theft-alarm system
N00510200156
The theft-alarm system is designed to provide protection from
unauthorized entry into the vehicle. This system is operated in
three stages: the first is the “armed” stage, the second is the
“alarm” stage, and third is the “disarmed” stage. If triggered,
the system provides both audible and visual alarm signals.
Armed stagePark the vehicle and stop the engine. Arm the system as
described below.
1. Turn the ignition switch to the “LOCK” position.
Also, if a key was used to start the engine, remove the key
from the ignition switch.
2. Make sure that the engine hood is locked.
3. Lock all doors and the tailgate by the remote control trans-
mitter, using either the F.A.S.T.-key.NOTE

If a door is open, after locking with the remote control
transmitter, close the door.
CAUTION
!

Do not modify or add parts to the theft-alarm sys-
tem. Doing so could cause the theft-alarm to mal-
function.
Arm the system and leave
BK0115300US.book 66 ページ ２００９年７月１６日　木曜日　午前９時１３分

Features and controls
3-67
3
At this time, the theft-alarm indicator (A) on the audio
panel flashes for confirmation. [The buzzer sounds inter-
mittently at the same time the theft-alarm indicator (A)
flashes. (if so equipped)]
4. The system has entered the armed stage after about 20
seconds, when the theft-alarm indicator (A) flashing
becomes slower. (The buzzer stops at this time.)
The theft-alarm indicator (A) continues to flash while the
system is in the armed stage.
NOTE

If the engine hood is open, the theft-alarm indicator (A)
illuminates and the system cannot enter the armed stage.
The system enters the armed stage about 20 seconds after
the engine hood is closed.


The system will be disarmed if, while the theft-alarm indi-
cator (A) is illuminated, all doors and the tailgate are
unlocked by remote control transmitter, the F.A.S.T.-key.


The system will be disarmed if, while the theft-alarm indi-
cator is illuminated, the ignition switch is turned to the
“ON” or “ACC”.


The system will not be armed if a door is not completely
closed. If this happens, rearm the system as described
above.


The security alarm system can be activated when people
are riding inside the vehicle or when the windows are
open. To prevent accidental activation of the alarm, do not
set the system to the system armed mode while people are
riding in the vehicle.
BK0115300US.book 67 ページ ２００９年７月１６日　木曜日　午前９時１３分

3-68 Features and controls
3
Alarm stageThe alarm will be activated if any of the following occur while
the vehicle is parked and the system is armed.
1. One of the doors and the tailgate is opened without the
remote control transmitter, the F.A.S.T.-key.
2. The engine hood is opened.
Also, for vehicles equipped with the interior alarm sensor, the
alarm will be activated if any of the following occur.

Attempt an unauthorized moving of the vehicle. (the
impact detection function)


Detect a motion in the vehicle. (the interior intrusion
detection function)


Disconnect the battery terminal.
Type of alarmWhen the alarm is activated:
1. The headlights blink on and off for 3 minutes.
After 3 minutes the headlights automatically shut off.
2. The horn (the siren for vehicles equipped with the interior
alarm sensor) will sound intermittently for 3 minutes.NOTE

The alarm will continue to operate for 3 minutes. At the
end of that period, the alarm will automatically shut off to
save battery power. The system will then be rearmed until
the proper disarming step is taken.


The alarm will resume if unauthorized actions are taken
again, even if the alarm has stopped.
Horn or siren sounds!
Headlights blink on and off!
BK0115300US.book 68 ページ ２００９年７月１６日　木曜日　午前９時１３分

Features and controls
3-69
3


While the alarm is operating, it is displayed on the infor-
mation screen in the multi-information display.
Ty p e 1
Ty p e 2
Alarm deactivationThe alarm can be deactivated in the following ways.

By using the remote control transmitter or the F.A.S.T.-
key to lock or unlock the door or tailgate.


Turn the ignition switch to the “ON” or the “ACC” posi-
tion.
To activate and deactivate the impact detection function
and the interior intrusion detection function
(if so
equipped)
The impact detection function and the interior intrusion detec-
tion function can be deactivated when parking in automated car
parks or leaving pets in the vehicle.
To deactivate the function
1. Turn the ignition switch to the “LOCK” position.
Also, if a key was used to start the engine, remove the key
from the ignition switch.
2. Raise and hold the wiper and washer switch to the
“MIST” position for about 3 seconds. The buzzer will
sound once and the function will be deactivated.
BK0115300US.book 69 ページ ２００９年７月１６日　木曜日　午前９時１３分

3-70 Features and controls
3
To activate the function
After deactivating the function, it will be activated again using
one of the following methods.

Unlock the doors and the tailgate using the keyless entry
system or the F.A.S.T.-key.


Turn the ignition switch to the “ON” or “ACC” position.
To activate the function again before locking the doors and the
tailgate, raise and hold the wiper and washer switch to the
“MIST” position for about 3 seconds.
The buzzer will sound twice and the function will be activated.
NOTE

The sensitivity of the impact detection function and the
interior intrusion detection function can be adjusted. For
further details, please contact an authorized Mitsubishi
Motors dealer.
Disarmed stageThe system will be disarmed when either of the following steps
are taken:
1. All doors and the tailgate are unlocked by the remote con-
trol transmitter or the F.A.S.T.-key.
2. The ignition switch is turned to the “ACC” or “ON” posi-
tion.
3. If the UNLOCK button is pressed when all doors and the
tailgate are closed and no door is opened within approxi-
mately 30 seconds, re-arming will automatically occur.NOTE

Once the system has been disarmed, it cannot be rearmed
except by repeating the arming procedure.
Disarm...by remote control transmitter or F.A.S.T.-key
BK0115300US.book 70 ページ ２００９年７月１６日　木曜日　午前９時１３分

Features and controls
3-71
3
Testing the theft-alarm systemUse the following procedure to test the system:
1. Lower the driver’s window.
2. Arm the system as explained in “Armed stage”.
3. Make sure that the theft-alarm indicator comes on and
flash in approximately 20 seconds.
4. Wait a few seconds and then unlock the driver’s side door
by using the inside door lock knob and opening the door.
5. Make sure that the horn (the siren for vehicles equipped
with the interior alarm sensor) sounds intermittently and
the headlights blink when a door is opened.
6. Disarm the system by unlocking all doors and the tailgate
by the remote control trasmitter, the F.A.S.T.-key.
Power window control
N00510800354
NOTE

Never try to operate the main switch and sub-switch in
different directions at the same time. This will freeze the
window in position.


Operating the power windows repeatedly with the engine
stopped will run down the battery. Use the window
switches only while the engine is running.
1- Open (down)
2- Close (up)
1
2
BK0115300US.book 71 ページ ２００９年７月１６日　木曜日　午前９時１３分

Features and controls
3-219
3
Headlight flasher
N00550000185
You can flash the high beams by pulling the lever gently
toward you (2). The lights will go back to normal when you let
go. While the high beam is on, you will see a blue light on the
instrument panel.NOTE

You can flash the high beams by pulling the lever toward
you, even if the light switch is off.


If you turn the lights off with the head lights set to high-
beam illumination, the headlights are automatically
returned to their low-beam setting when the light switch is
next turned to the “ ” position.
Welcome light (for vehicles with the color multi-
information display)
N00563200035
This function turns on the front side-marker and parking lights
for about 30 seconds after the UNLOCK button (A) on the
remote control transmitter is pressed when the combination
headlights and dimmer switch is in the “OFF” or “AUTO”
position (for vehicles equipped with the automatic light con-
trol). If the combination headlights and dimmer switch is in the
“AUTO” position (for vehicles equipped with the automatic
light control), the welcome light function will operate only
when it is dark outside the vehicle.
BK0115300US.book 219 ページ ２００９年７月１６日　木曜日　午前９時１３分

3-220 Features and controls
3
NOTE

While the welcome light function is operating, perform
one of the following operations to cancel the function.
 Push the LOCK button (B) on the remote control trans-
mitter.
 Turn the combination headlights and dimmer switch to
the “ ” or “ ” position.
 Turn the ignition switch to the “ON” position.


It is possible to modify functions as follows:
 The headlights can be set to come on in the low beam
setting instead of the front side-marker and parking
lights.
 The welcome light function can be deactivated.
For details, consult a Mitsubishi Motors dealer.
Coming home light (for vehicles with the color
multi-information display)
N00547300038
This function turns on the headlights in the low beam setting
for about 30 seconds after the ignition switch is turned to the
“LOCK” position.
1. Turn the combination headlights and dimmer switch to the
“OFF” or “AUTO” position (for vehicles equipped with
the automatic light control).
2. Turn the ignition switch to the “LOCK” position. Also, if
a key was used to start the engine, remove the key from
the ignition switch.
3. Within 60 seconds of turning the ignition switch to the
“LOCK” position, pull the turn signal lever toward you.
BK0115300US.book 220 ページ ２００９年７月１６日　木曜日　午前９時１３分