Page 230 of 594
Features and controls
3-145
3
If the warning light illuminates while driving
N00532800279
1. If the tire pressure monitoring system warning light illu-
minates, avoid hard braking, sharp steering maneuvers
and high speeds. You should stop and adjust the tires to
the proper inflation pressure as soon as possible. Adjust
the spare tire at the same time. Refer to “Tires” on page 7-
19.NOTE
In addition, the warning display is displayed on the infor-
mation screen in the multi-information display.
Once adjustments have been made, the warning light will
go off after a few minutes of driving.
2. If the tire pressure monitoring system warning light
remains illuminated after you have been driving for about
20 minutes after you adjust the tire inflation pressure, one
or more of the tires may have a puncture. Inspect the tire
and if it has a puncture, have it repaired by an authorized
Mitsubishi Motors dealer as soon as possible.
NOTE
To avoid the risk of damage to the tire inflation pressure
sensors, have any punctured tire repaired by an authorized
Mitsubishi Motors dealer. If the tire repair is not done by
an authorized Mitsubishi Motors dealer, it is not covered
by your warranty.
Do not use an aerosol puncture-repair product on any tire,
as it could damage the tire inflation pressure sensors.
Have any puncture repaired by an authorized Mitsubishi
Motors dealer.
WA R N I N G
!
If the warning light / display illuminates while you
are driving, avoid hard braking, sharp steering
maneuvers and high speeds. Driving with an under-
inflated tire adversely affects vehicle performance
and can result in an accident.
CAUTION
!
If a tire has a puncture, replace that tire with the
spare tire. Driving on a punctured tire could lead to
an accident.
The warning light / display may not illuminate
immediately in the event of a tire blowout or rapid
leak.
BK0105501US.book 145 ページ ２００９年８月１０日 月曜日 午前１０時３２分
Page 231 of 594
3-146 Features and controls
3
The tire pressure monitoring system may not work normally in
the following circumstances:
A wireless facility or device using the same frequency is
near the vehicle.
Snow or ice is stuck inside the fenders and/or on the
wheels.
The tire inflation pressure sensor’s battery is exhausted.
Wheels other than Mitsubishi genuine wheels are being
used.
Wheels that are not fitted with tire inflation pressure sen-
sors are being used.
Wheels whose ID codes are not memorized by the vehicle
are used.
Compact spare tire is fitted on a road wheel.
NOTE
Tire inflation pressures vary with the ambient tempera-
ture. If the vehicle is subjected to large variations in ambi-
ent temperature, the tire inflation pressures may be under-
inflated (causing the warning light to come on) when the
ambient temperature is relatively low. If the warning light
comes on, adjust the tire inflation pressure.
Whenever the tires and wheels are replaced with
new ones
N00532900124
If you use new wheels with new tire inflation pressure sensors,
their ID codes must be programmed into the tire pressure mon-
itoring system. Have tire and wheel replacement performed by
an authorized Mitsubishi Motors dealer to avoid the risk of
damaging the tire inflation pressure sensors. If the wheel
replacement is not done by an authorized Mitsubishi Motors
dealer, any resulting damage or system performance problems
are not covered by your warranty.
CAUTION
!
The use of non-genuine wheels will prevent the
proper fit of the tire inflation pressure sensors,
resulting in air leakage or damage of the sensors.
BK0105501US.book 146 ページ ２００９年８月１０日 月曜日 午前１０時３２分
Page 236 of 594
Features and controls
3-151
3 Multi-information display
N00555000151
The multi-information display displays warnings, the odometer/trip odometer, service reminder, engine coolant temperature, fuel
remaining, outside temperature, Twin Clutch SST control mode, S-AWC (Super-All Wheel Control) control mode, gearshift lever
position, average and momentary fuel consumption, driving range, average speed, S-AWC (Super-All Wheel Control) operation
display, instrument brightness, etc.
It is also possible to change elements such as the language and units used on the multi-information display.
With ignition switch in the
“OFF” positionWith ignition switch in the “ON”
position (Twin Clutch SST)With ignition switch in the “ON”
position (manual transaxle)
1- “!” Warning display screen (With ignition switch in the
“OFF” position) →P. 3 - 1 5 3
2- Information screen (With ignition switch in the “OFF” posi-
tion) → P.3-154
Interrupt display screen (With ignition switch in the “OFF”
position) → P.3-156
3- Door ajar warning display screen (With ignition switch in
the “OFF” position) → P.3-157
4- S-AWC control mode display screen → P.3-159
5- Outside temperature display screen → P.3-1676- “!” Warning display screen (With ignition switch in the
“ON” position) → P.3-159
7- Information screen (With ignition switch in the “ON” posi-
tion) → P.3-160
Interrupt display screen (With ignition switch in the “ON”
position) → P. 3 - 1 6 5
8- Fuel remaining display screen → P.3-167
9- Twin Clutch SST control mode display screen (if so
equipped) → P. 3 - 1 6 7
BK0105501US.book 151 ページ ２００９年８月１０日 月曜日 午前１０時３２分
Page 237 of 594
3-152 Features and controls
3
NOTE
The trip computer function fuel units, temperature units,
display language, and other settings can be changed.
Refer to “Changing the function settings (With ignition
switch in the “ON” position)” on page 3-171.
The display screen is different depending on whether the
ignition switch in the “OFF” or “ON” position.
Refer to “Information screen (With ignition switch in the
“OFF” position)” on page 3-154.
Refer to “Warning display list (With ignition switch in the
“OFF” position)” on page 3-185.
Refer to “Information screen (With ignition switch turned
from “OFF” to “ON”)” on page 3-158.
Refer to “Information screen (With ignition switch in the
“ON” position)” on page 3-160.
Refer to “Warning display list (With ignition switch in the
“ON” position)” on page 3-188.
10- Gearshift lever position display screen (if so equipped) →
P.3-166
11- Active Stability Control (ASC) OFF display screen → P. 3 -
129BK0105501US.book 152 ページ ２００９年８月１０日 月曜日 午前１０時３２分
Page 238 of 594
Features and controls
3-153
3
Multi-information meter switch
N00555100110
The multi-information meter switch is a button marked
“INFO” on the left side of the dash.
Each time the multi-information meter switch is operated, a
sound is emitted and the multi-information display changes
between information such as warnings, service reminder, aver-
age and momentary fuel consumption, driving range, average
speed, and S-AWC operation display.
It is also possible to change elements such as the language and
units used on the multi-information display by operating the
multi-information meter switch.
“!” Warning display screen (With ignition switch
in the “OFF” position)
N00555200078
If you press the multi-information meter switch and return
from the warning display screen to the previous screen, the “!”
warning is displayed.
Refer to “Returning to the display screen from before the warn-
ing display” on page 3-156.
This mark is also displayed if there is another warning other
than the one displayed. When the cause of the warning display
is eliminated, the “!” warning goes out automatically.NOTE
When the “!” warning is displayed, the warning display
screen can be redisplayed on the information screen.
Refer to “Information screen (With ignition switch in the
“OFF” position)” on page 3-154.
Refer to “Information screen (With ignition switch in the
“ON” position)” on page 3-160.
BK0105501US.book 153 ページ ２００９年８月１０日 月曜日 午前１０時３２分
Page 239 of 594
3-154 Features and controls
3
Information screen (With ignition switch in the
“OFF” position)
N00555300095
Each time you lightly press the multi-information meter
switch, the display screen switches in the following order.
1-
Odometer/Trip odometer
2-
Odometer/Trip odometer
3- Service reminder
4- Redisplay of a warning display screen
When there is no
warning display
When there is a
warning display
BK0105501US.book 154 ページ ２００９年８月１０日 月曜日 午前１０時３２分
Page 240 of 594
Features and controls
3-155
3
Odometer/Trip odometer
N00555400083
Each time you lightly press the multi-information meter
switch, the display screen switches.
Odometer/tripmeter → Odometer/tripmeter → Service
reminder → Redisplay of a warning display screen → Odome-
ter/tripmeter .
Odometer
Shows the total distance traveled.
Trip odometer
Shows the distance traveled between two points.
To reset the trip odometer
To return the display to 0, hold down the multi-information
meter switch for about 2 seconds or more. Only the currently
displayed value will be reset.
Example
If tripmeter is displayed, only tripmeter will be reset.
NOTE
If there is no warning display, the switching sequence is:
odometer/tripmeter → odometer/tripmeter → ser-
vice reminder → odometer/tripmeter .
Both tripmeters and can count up to 9999.9
miles/kilometers.
When a tripmeter goes past 9999.9 miles/kilometers, it
returns to 0.0 miles/kilometers.
When disconnecting the battery terminal, the memories of
tripmeter displays and are cleared, and their dis-
plays return to “0.0 miles/kilometers”.
Service reminder
N00555500013
Shows the distance and number of months until the next peri-
odic inspection.
Refer to “Service reminder” on page 3-168.
Usage examples for tripmeter , tripmeter
It is possible to measure two currently traveled distances,
from home using tripmeter and from a particular point
on the way using tripmeter .
BK0105501US.book 155 ページ ２００９年８月１０日 月曜日 午前１０時３２分
Page 241 of 594
3-156 Features and controls
3
Interrupt display screen (With ignition switch in
the “OFF” position)
N00559600139
When there is information to be announced, such as a key
reminder, the buzzer sounds and switches to the warning dis-
play screen. Refer to the appropriate page and take the neces-
sary measures.
When the cause of the warning display is eliminated, the warn-
ing display goes out automatically.
Refer to “Warning display list (With ignition switch in the
“OFF” position)” on page 3-185.
Returning to the display screen from before the warn-
ing displayEven if the cause of the warning display is not eliminated, you
can return to the screen that was displayed before the warning
display.
If you press the multi-information meter switch, the display
screen switches to the screen display from before the warning
and the “!” warning is displayed.
1- Information generated
2- Cause eliminated
A- “!” warning
BK0105501US.book 156 ページ ２００９年８月１０日 月曜日 午前１０時３２分
