2010 MITSUBISHI GRANDIS change wheel

Turn/Lane-change signals
E00506501156
The
turn-signal lamps flash when the switch is op-
erated (with the ignition switch in the “ON” posi-
tion). At the same time, the turn signal indicator
flashes. 1- Turn-signals
When
making a normal turn, use position
(1). The lever will return automatically when
cornering is completed.
There are times when the lever will not re-
turn after cornering. This occurs when the
steering wheel is turned only slightly.
In such cases, return the lever by hand.
2- Lane-change signals When changing lanes, use position (2). It
will return to the neutral position when re-
leased.
NOTE l If the lamp flashes unusually quickly, the
bulb in a turn-signal lamp may have burned
out. We recommend you to have the vehicle
inspected. l
It
is possible to activate the following func-
tions. For further information, we recom-
mend you to consult a MITSUBISHI
MOTORS Authorized Service Point.
On a vehicle equipped with a Multi Display
Station (MDS), the functions can be adjusted
on the screen. Refer to the separate operation
manual for details. • Sounding of a buzzer as the turn-signallamps flash.
• Flashing of the turn-signal lamps and the indication lamp in the meter when the lev-
er is operated with the ignition switch in
the “ACC” position. Hazard warning flasher switch
E00506600567
Use
the hazard warning flasher switch when the ve-
hicle has to be parked on the road for any emergency.
The hazard warning flashers can always be operat-
ed, regardless of the position of the ignition key.

Push the switch to turn on the hazard warning flash-
ers; push the switch again to turn them off.
When this switch is operated, all turn-signal lamps
flash continuously, as do the turn-signal indication
lamps in the instrument cluster. NOTE
l If

the lamps are kept flashing for a long time,
the battery will be discharged, resulting in
hard engine starting or no start condition. Instruments and controls
3-21 3
Presented by http://mmc-manuals.ru/ \251

If the vehicle breaks down
............................................................ 6-02
Emergency starting ....................................................................... 6-02
Engine overheating ....................................................................... 6-04
Tools and jack ............................................................................... 6-06
Jacking up the vehicle
................................................................... 6-07
Spare wheel...................................................................................6-08
How to change a tyre .................................................................... 6-11
Towing.......................................................................................... 6-14
Operation under adverse driving conditions .................................6-18For emergencies
6
Presented by http://mmc-manuals.ru/ \251

3. Retract the jack, then remove it from its stor-
age location. To store
1. Retract
the jack, then return it to its original
position.
To retract
To expand 2. Expand the jack to lock it securely in place.
3. Return

the luggage floor board to its original
position. Jacking up the vehicle
E00801001393
1.

Park the vehicle on level and stable ground.
2. Set the parking brake firmly.
3. On vehicles with M/T, turn the ignition key to the “LOCK” position, move the gearshift
lever to the “R” (Reverse) position.
On vehicles with A/T, move the selector lev-
er to the “P” (PARK) position, turn the igni-
tion key to the “LOCK” position.
4. Turn on the hazard warning flashers and set up a warning triangle, flashing signal lamp,
etc., at an adequate distance from the vehi-
cle, and have all your passengers leave the ve-
hicle.
5. To prevent the vehicle from rolling when it is raised on the jack, place chocks or blocks
(A) at the tyre that is diagonally opposite
from the tyre (B) you are changing. WARNING
l Be
sure to apply chocks or blocks to the
correct tyre when jacking up the vehicle.
If the vehicle moves while jacked up, the
jack could slip out of position, leading to
an accident.
NOTE l The

chocks shown in the illustration do not
come with your vehicle. It is recommended
that you keep one in the vehicle for use if nee-
ded.
l If chocks are not available, use stones or any
other objects that are large enough to hold
the wheel in position.
6. Place the jack under one of the jacking points (C) shown in the illustration. Use the
jacking point closest to the tyre you wish to
change. For emergencies
6-07 6
Presented by http://mmc-manuals.ru/ \251

WARNING
l Set the jack only at the positions shown
here. If the jack is set at a wrong position,
it could dent your vehicle or the jack
might fall over and cause personal injury.
l Do not use the jack on a tilted or soft sur-
face.
Otherwise, the jack might slip and cause
personal injury. Always use the jack on a
flat, hard surface. Before setting the jack,
make sure there are no sand or pebbles
under the jack base.
7. Rotate
the jack by hand until the flange por- tion (D) fits in the groove (E) at the top of
the jack. 8. Remove
the wheel nut wrench and bar from
under the third seat. (Refer to “Tools and
jack” on page 6-06.)
9. Insert the bar (F) into the wheel nut wrench (G). Then put the end of the bar into the
shaft’s jack end, as shown in the illustration. Slowly rotate the wheel nut wrench until the
tyre is raised slightly off the ground surface.
WARNING
l Stop
jacking up the vehicle as soon as the
tyre is raised off the ground. It is danger-
ous to raise the vehicle any higher.
l Do not get under your vehicle while using
the jack.
l Do not bump the raised vehicle or leave it
sitting on the jack for a long time. Both
are very dangerous.
l Do not use a jack except the one that
came with your vehicle.
l The jack should not be used for any pur-
pose other than to change a tyre.
l No one should be in your vehicle when us-
ing the jack.
l Do not start or run the engine while your
vehicle is on the jack.
l Do not turn the raised wheel. The tyres
still on the ground could turn and make
your vehicle fall off the jack. Spare wheel
E00801101440
Check

the air pressure of the spare tyre frequently
and make sure it is ready for emergency use at any
time.

Maintaining the spare wheel at the highest speci-
fied air pressure will ensure that it can always be
used under any conditions (city/high-speed driving,
varying load weight, etc.).
The spare wheel is stored under the rear of the body.
Compact spare wheel
The compact spare tyre is designed to save space in
the luggage compartment and its lighter weight
makes it easier to use if a flat tyre occurs. CAUTION
l
The
pressure should be periodically
checked and maintained at the specified
pressure while the tyre is stowed.
Driving with an insufficient tyre pressure
can lead to an accident. If you have no
choice but to drive with an insufficient
tyre pressure, keep your speed down and
inflate the tyre to the correct pressure as
soon as possible. (Refer to “Tyre inflation
pressures” on page 8-12.)
l The compact spare wheel is for tempora-
ry use only and should be removed as
soon as the original wheel can be re-
paired or replaced.
l The vehicle must not be driven at speeds
in excess of 80 km/h (50 mph) while using
the compact spare wheel. For emergencies
6-08
6
Presented by http://mmc-manuals.ru/ \251

How to change a tyre
E00801202523
Before
changing a tyre, first stop your vehicle in a
safe, flat location. 1. Park the vehicle on level and stable ground.
2. Set the parking brake firmly.
3. On vehicles with M/T, turn the ignition keyto the “LOCK” position, move the gearshift
lever to the “R” (Reverse) position.
On vehicles with A/T, move the selector lev-
er to the “P” (PARK) position, turn the igni-
tion key to the “LOCK” position.
4. Turn on the hazard warning flashers and set up a warning triangle, flashing signal lamp,
etc., at an adequate distance from the vehi-
cle, and have all your passengers leave the ve-
hicle.
5. To prevent the vehicle from rolling when it is raised on the jack, place chocks or blocks
(A) at the tyre that is diagonally opposite
from the tyre (B) you are changing. WARNING
l Be
sure to apply chocks or blocks to the
correct tyre when jacking up the vehicle.
If the vehicle moves while jacked up, the
jack could slip out of position, leading to
an accident.
NOTE l The

chocks shown in the illustration do not
come with your vehicle. It is recommended
that you keep one in the vehicle for use if nee-
ded.
l If chocks are not available, use stones or any
other objects that are large enough to hold
the wheel in position.
6. Get the spare wheel, jack, jack handle and wheel nut wrench ready. NOTE
l Put

the spare wheel under the vehicle body
near the jack. This makes it safer if the jack
slips out of position. 7. On
vehicles with wheel covers, first remove
the covers (refer to “Wheel covers” on page
6-13). Then loosen the wheel nuts with the
wheel nut wrench. Do not remove the wheel
nuts yet. 8. Find
the closest jacking point to the flat tyre
(refer to the “Jacking up the vehicle” on page
6-07). Then position the jack and raise the ve-
hicle until the tyre is slightly off the ground.
9. Remove the wheel nuts with the wheel nut wrench, then take the wheel off. CAUTION
l
Handle
the wheel carefully when chang-
ing the tyre, to avoid scratching the wheel
surface.
10. Clean
out any mud, etc. on the hub surface (C), hub bolts (D) or in the installation holes
(E) in the wheel, and then mount the spare tyre. For emergencies
6-11 6
Presented by http://mmc-manuals.ru/ \251

WARNING
l Mount the spare wheel with the valve
stem (F) facing outboard. If you cannot
see the valve stem (F), you have installed
the wheel backwards.
Operating the vehicle with the spare
wheel installed backwards can cause vehi-
cle damage and result in an accident. 11. Finger-tighten

the wheel nuts. (Turn them
clockwise.)
Vehicle with steel wheels
Tighten
the wheel nuts until the tapered
parts of the wheel nuts make light contact
with the seats of the wheel holes and the
wheel is not loose.
Tighten the wheel nuts in the same way
with a compact spare wheel.
Vehicle with aluminium wheels
With

a normal wheel, tighten the wheel
nuts until the flanges of the wheel nuts
touch the wheel and the wheel is not loose.
Normal wheel With a compact spare wheel, tighten the
wheel

nuts until the tapered parts of the wheel nuts make light contact with the
seats

of the wheel holes and the wheel is
not loose.
Compact spare wheel CAUTION
l
Never
apply oil to either the wheel bolts
or the nuts, or they will tighten too much.
NOTE l Flange

nuts can be temporarily used on the
spare wheel, but return to the original wheel
and tyre as soon as possible.
l If all four aluminium wheels are changed to
steel wheels, use tapered nuts.
12. Lower the vehicle slowly and then tighten the nuts in the order shown in the illustration
until each nut has been tightened to the tor-
que listed here.
Tightening torque
88 to 108 N•m For emergencies
6-12
6
Presented by http://mmc-manuals.ru/ \251

CAUTION
l
If the tyres have arrows (A) indicating
the correct direction of rotation, swap the
front and rear wheels on the left hand
side of the vehicle and the front and rear
wheels on the right hand side of the vehi-
cle separately. Keep each tyre on its origi-
nal side of the vehicle. When fitting the
tyres, make sure the arrows point in the
direction in which the wheels will turn
when the vehicle moves forward. Any
tyre whose arrow points in the wrong di-
rection will not perform to its full poten-
tial.
Front CAUTION
l
Avoid
the combined use of different types
of tyres.
Using different types of tyres can affect ve-
hicle performance and safety. Snow tyres
E01002000725
The

use of snow tyres is recommended for driving
on snow and ice. To preserve driving stability,
mount snow tyres of the same size and tread pat-
tern on all 4 wheels.
Snow tyres worn more than 50% are no longer suit-
able for use as snow tyres.
Snow tyres which do not meet specifications must
not be used. CAUTION
l
Observe
permissable maximum speed for
your snow tyres and the legal speed limit.
NOTE l The

laws and regulations concerning snow
tyres (driving speed, required use, type, etc.)
vary. Find out and follow the laws and regu-
lations in the area you intend to drive.
l If flange nuts are used on your vehicle,
change to tapered nuts when steel wheels are
used.
Tyre chains E01002101130
If tyre chains have to be used, ensure that they are
fitted only on the drive wheels (front).
Use

only tyre chains which are designed for use
with the tyres mounted on the vehicle: use of the in-
correct size or type of chain could result in damage
to the vehicle body.
Before fitting tyre chains, We recommend you to
consult a MITSUBISHI MOTORS Authorized Serv-
ice Point. Tyre size Wheel size Max chain
height[mm]
215/60R16 16x6.5 JJ 9
215/55R17 17x7.0 J The speed limit for tyre chain is 50 km/h (30

mph)
and remove the tyre chains as soon as possible on
snow free roads. WARNING
l DO
NOT use a jack when fitting the
chains, as in thsee conditions, the tyres
may slip on the icy road causing the vehi-
cle to slip off the jack. CAUTION
l
Practice
fitting the chains before you
need them.
Don’t expect help from other people in
the cold.
l Choose a clear straight stretch of road
where you can pull over and still be seen
while you are fitting the chains.
l Do not fit chains before you need them.
This will wear out your tyres and the
road surface.
l After driving around 100-300 metres,
stop and retighten the chains.
l Care should be taken with extremes of
steering lock to prevent possible contact
between the chains and the vehicle body. Maintenance
8-14
8
Presented by http://mmc-manuals.ru/ \251

A
Accessory (Installation) 04
Accessory socket 5-35
Active stability control (ASC)
4-23
Indication lamp 4-24
Active stability control Stability control function 4-24
Additional equipment 8-19
Air conditioning Front automatic air conditioning 5-05
Important operation tips for the air condition-
ing 5-11
Rear automatic air conditioning 5-09
Air purifier (with deodorizing function) 5-12
Airbag 2-29
Antenna Glass antenna 5-31
Anti-lock brake system (ABS) 4-21 Warning lamp 4-21
Armrest 2-06,2-08
Ashtray 5-33
Assist grip 5-44
Audio Error codes 5-28
Handling of compact discs 5-30
LW/MW/FM electronic tuning radio with CD
player 5-13
Auto-speed (cruise) control 4-25 Indication lamp 4-26
Automatic headlamp levelling 3-20
Automatic headlamp levelling warning lamp 3-20
Automatic transmission Fluid 8-08,9-15
Selector lever operation 4-15
Sports mode 4-17 BBattery 8-10
Charge warning lamp 3-08
Discharged battery (Emergency starting)
6-02
Specification 9-10
Bonnet 8-03
Bottle holder 5-41
Brake Anti-lock brake 4-21
Braking 4-20
Fluid 8-09,9-14
Parking brake 4-04
Parking brake stroke 8-16
Pedal free play 8-16
Warning lamp 3-06
Bulb capacity 8-25
C Capacities 9-14
Card holder 5-32,5-42
Cargo loads 4-32
Cargo net 5-45
Catalytic converter

8-02
Central door locks 1-07
Changing gears 4-14
Charge warning lamp 3-08
Chassis number 9-02
Check engine warning lamp 3-07,3-08
Child restraint 2-21
Child-protection rear doors 1-08
Cigarette lighter 5-34
Cleaning Exterior of your vehicle 7-03
Genuine leather 7-02
Interior of your vehicle 7-02
Plastic, vinyl leather, etc 7-02 Washing 7-03
Clutch Fluid 8-09,9-14
Pedal free play 8-15
Coat hooks 5-44
Combination headlamps and dipper switch

3-18
Compact spare wheel 6-08
Coolant (Engine) 8-06,9-15
Corner sensor system 4-29
Cup holder 5-40
D Daytime dipper button 3-04
Demister (rear window) 3-25
Diesel particulate filter (DPF)

4-12
Diesel preheat indication lamp 3-06
Dimensions 9-04
Dipper (High/Low beam change) 3-19
Door lamps 5-37 Bulb capacity 8-26
Replacement 8-31
Doors 1-06 Central door locks 1-07
Child-protection 1-08
Lock and unlock 1-06
Driving, alcohol and drugs 4-02
E Economical driving 4-02
Economical driving speed

4-14
Electric window control 1-11
Electrical system 9-10
Electronic immobilizer (Anti-theft starting sys-
tem) 1-03
Emergency starting 6-02
Engine specifications 9-08
Engine Alphabetical index
1
Presented by http://mmc-manuals.ru/ \251