2010 MITSUBISHI GRANDIS engine coolant

Low fuel warning lamp
E00508100638
The
warning lamp (A) illuminates when the fuel lev-
el is getting low (approx. 10 litres) with the igni-
tion switch in the “ON” position. Refuel as soon as
possible. NOTE
l On

inclines or curves, due to the movement
of fuel in the tank, the low fuel warning lamp
may indicate incorrectly. Water temperature gauge
E00500800495
The

water temperature gauge indicates the engine
coolant temperature when the ignition switch is in
the “ON” position. CAUTION
l
If
the indication needle enters the zone
(A) while the engine is running, it indi-
cates that the engine is possibly overheat-
ing. Immediately park your vehicle in a
safe place and make the necessary correc-
tions. (Refer to “Engine overheating” on
page 6-04.)
While driving, care should always be tak-
en to maintain the normal operating tem-
perature.
Daytime dipper button E00508800026
By pressing the daytime dipper button, you can
change

the brightness of the backlighting in meters
and instrument panel. NOTE
l The

brightness can be adjusted among 4 lev-
els in accordance with the on/off condition of
the tail lamps. NOTE
l The

meter brightness is memorized and main-
tained even if the ignition switch is turned to
the “LOCK” position. Instruments and controls
3-04
3
Presented by http://mmc-manuals.ru/ \251

Steering wheel lock
E00601500083To lock
Remove the key at the “LOCK” position.
Turn the steering wheel until it is locked.
To unlock
Turn
the key to the “ACC” position while moving
the steering wheel slightly. CAUTION
l
Remove the key when leaving the vehicle.
NOTE l If

the front wheels are turned, the anti-theft
lock may sometimes make it difficult to turn
the key from “LOCK” to “ACC”. Firmly
turn the steering wheel to the left or to the
right as you turn the key. Starting
E00601600941
Tips for starting l Do

not operate the starter motor continuous-
ly longer than 10 seconds; doing so could
run down the battery. If the engine does not
start, turn the ignition switch back to
“LOCK” position, wait a few seconds, and
then try again.
Trying repeatedly with the starter motor still
turning will damage the starter mechanism.
l If the engine cannot be started because the
battery is weak or dead, refer to the “Emer-
gency starting” section for instructions on
starting the engine.
l The engine is well warmed up if the coolant
temperature gauge needle starts to move (the
engine speed decreases). Extended warming-
up operation will result in excessive fuel con-
sumption. WARNING
l Never
run the engine in a closed or poor-
ly ventilated area any longer than is nee-
ded to move your vehicle in or out of the
area. Carbon monoxide gases are odour-
less and can be fatal. CAUTION
l
Never
attempt to start the engine by push-
ing or pulling the vehicle. Especially in
the A/T, since the structure is different
from a M/T, it is not possible to start the
engine by using this technique. Never at-
tempt this or it could damage the A/T.
l Do not run the engine at high rpm or
drive the vehicle at high speed until the en-
gine has had a chance to warm up.
l Release the ignition key as soon as the en-
gine starts to avoid damaging the starter
motor.
l If your vehicle is equipped with a turbo-
charger, do not stop the engine immedi-
ately after high-speed or uphill driving.
First allow the engine to idle to give the
turbocharger a chance to cool down.
Starting the engine (petrol-powered ve-
hicles) E00601701239
This vehicles is equipped with an electronically con-
trolled

fuel injection system which is automatically
controlled. When starting the engine, do not de-
press the accelerator pedal.
Normal conditions
The starting procedure is as follows: 1. Insert the ignition key and fasten the seat belt.
2. Make sure the parking brake is applied.
3. Depress and hold the brake pedal.
4. Fully depress the clutch pedal (M/T).
5. On vehicles with M/T, place the gearshift lev-er in the “N” (Neutral) position. Starting and driving
4-10
4
Presented by http://mmc-manuals.ru/ \251

On vehicles with A/T,
make sure the selector
lever is in the “P” (PARK) position. 6. After
turning the ignition key to the “ON” po-
sition, make certain that all warning lamps
are functioning properly before starting the
engine.
7. Turn the ignition key to the “START” posi- tion without depressing the accelerator pedal,
and release it when the engine starts.
At extreme cold ambient temperature
If the engine won’t start, depress the accelerator ped-
al about halfway while cranking the engine. Once
the engine starts, release the accelerator pedal. CAUTION
l
When
starting the engine, make sure that
you press on the brake pedal. At extreme
cold ambient temperature move your foot
to the brake pedal immediately after the
engine has started. Flooded engine
If

the engine was flooded during starting, first oper-
ate the starter for 5 to 6 seconds while fully depress-
ing the accelerator pedal, then start the engine with-
out depressing the accelerator pedal.
Using the MIVEC engine
The MIVEC engine automatically switches its in-
take-valve control between a low-speed mode and
a high-speed mode in accordance with driving con-
ditions for maximum engine performance.
NOTE
l To protect the engine, the high-speed mode
may not be selected while the engine coolant
temperature is low. In such a case, the engine
revolutions do not rise to over 5,000 rpm
even if the accelerator pedal is depressed.
Starting the engine (diesel-powered ve-
hicles) E00601701242
1. Insert
the ignition key and fasten the seat belt.
2. Make sure the parking brake is applied.
3. Depress and hold the brake pedal.
4. Fully depress the clutch pedal. 5. Place
the gearshift lever in the “N” (Neutral)
position. 6. Turn the ignition key to the “ON” position.
The
diesel preheat indication lamp will first
illuminate, and then after a short time go out,
indicating that preheating is completed.
NOTE l If the engine is cold, the diesel preheat indi-
cation lamp is on for a longer time.
l When the engine has not been started within
about 5 seconds after the diesel preheat indi-
cation lamp went out, return the ignition key
to the “LOCK” position. Then, turn the key
to the “ON” position to preheat the engine
again.
l When the engine is warm, the diesel preheat
indication lamp does not come on even if the
ignition key is placed in the “ON” position.
Start the engine by turning the ignition key
right to the “START” position.
7. Turn the ignition key to the “START” posi- tion without depressing the accelerator pedal,
and release it when the engine starts. Starting and driving
4-11 4M/T
A/T
Presented by http://mmc-manuals.ru/ \251

NOTE
l While
the engine coolant temperature is low,
the temperature of the air from the heater
will be cool/cold until the engine warms up,
even if you have selected warm air with the
dial.
l When the temperature is set to the highest or
the lowest, the air selection and the air condi-
tioning will be automatically changed as fol-
lows.
Also, if manually operated after an automatic
changeover, manual operation will be selec-
ted.
• Quick Heating (When the temperature isset to the highest setting)
Outside air will be introduced and the air
conditioning will stop.
• Quick Cooling (When the temperature is set to the lowest setting)
Inside air will be recirculated and the air
conditioning will operate. Mode selection dial
E00703200418
To
change the position and amount of air flowing
from the ventilators, turn the mode selection dial.
(Refer to “Changing the front mode selection” on
page 5-03.) CAUTION
l
When
using the mode selection dial be-
tween the “ ”
and “ ” positions, pre-
vent fogging by pressing the air selection
switch to select outside air.
(Refer to “Air selection switch” on page
5-06.)
Air selection switch E00703400511
To change the air selection, simply press the air se-
lection switch.
l Outside air {Indication lamp (A) is OFF}
Outside

air is introduced into the passenger
compartment. l
Recirculated air {Indication lamp (A) is ON}
Air

is recirculated inside the passenger com-
partment. CAUTION
l
Normally, use the outside position to keep
the

windscreen and side windows clear
and quickly remove fog or frost from the
windscreen.
If high cooling performance is desired, or
if the outside air is dusty or otherwise con-
taminated use the recirculation position.
Switch to the outside position periodically
to increase ventilation so that the win-
dows do not become fogged up.
l Use of the recirculation position for exten-
ded time may cause the windows to fog up. For pleasant driving
5-06
5
Presented by http://mmc-manuals.ru/ \251

NOTE
l Set
the temperature at about 22 under normal
conditions.
l While the engine coolant temperature is low,
the temperature of the air from the heater
will be cool/cold until the engine warms up,
even if you have selected warm air with the
dial. To prevent the windscreen and win-
dows from fogging up, the ventilator mode
will be changed to “ ”
and the blower
speed will be reduced.
l If the blower speed selection dial, air condi-
tioning switch, mode selection dial, or air se-
lection switch is operated while the system is
operating in the AUTO mode, the activated
function overrides the corresponding func-
tion of automatic control. All other functions
remain under automatic control.
Operating the system in manual air
mode E00704200011
Blower speed and ventilator mode may be control-
led

manually by setting the blower speed selection
dial and the mode selection dial to the desired posi-
tions. To return to automatic operation, set the dials
to the “AUTO” position.
Demisting of the windscreen and door windows E00704300546CAUTION
l
For
safety, make sure you have a clear
view through all the windows. To remove frost or mist from the windscreen and
door

windows, use the mode selection dial (“ ”
or “ ”).
For ordinary demisting
Use

this setting to keep the windscreen and door
windows clear of mist, and to keep the leg area heat-
ed (when driving in rain or snow). 1. Set
the air selection switch (A) to the outside
position.
2. Set the mode selection dial to the “ ” posi-
tion.
3. Select

your desired blower speed by turning
the blower speed selection dial.
4. Select your desired temperature by turning the temperature control dial.
5. Push the air conditioning switch (B). For quick demisting
1.
Set the mode selection dial to the
“ ” posi-
tion.
2.
Set the blower to the maximum speed.
3. Set the temperature to the highest position.
NOTE l While the mode selection dial is set to the
“ ”
position, the air conditioning will oper-
ate automatically and the outside air position
will also be selected automatically.
l Do not set the temperature control dial to the
max. cool position. Cool air will blow
against the window glasses and form mist on
them. For pleasant driving
5-08
5
Presented by http://mmc-manuals.ru/ \251

Blower speed selection switch
E00706300104
When
the blower speed selection switch or AUTO
switch is pressed, the air conditioning (cooling and
dehumidifying functions) starts operating. When
the OFF switch (A) is pressed, it stops.
The indication lamp (B) for the selected blower
speed illuminates. NOTE
l The blower speed is memorized when the en-
gine is shut down.
If

the battery is disconnected and reconnec-
ted, however, the memory is erased and the
blower speed is automatically set to the
“OFF” position.
Temperature control lever E00706400059
The temperature control lever is used to adjust the
air temperature. Move it rightward to increase the temperature and
leftward to reduce the temperature.
1- Low
2-

High
NOTE l The mode changes in accordance with the air
temperature. (Refer to “Changing the rear
mode selection” on page 5-04.)
l When the engine coolant temperature is ex-
tremely low (for example, in extremely cold
weather), moving the temperature control lev-
er has no effect on the air temperature. Operating the system in automatic
mode
E00706800141 1. Press the AUTO switch (A).
2.

Set the desired temperature using the temper-ature control lever (B). The temperature can
be set within a range from the minimum to
the maximum.
NOTE l Adjust the temperature to the desired level us-
ing the temperature control lever (centred for
reference).
l When the engine coolant temperature is ex-
tremely low (for example, in extremely cold
weather), moving the temperature control lev-
er has no effect on the air temperature. For pleasant driving
5-10
5
Presented by http://mmc-manuals.ru/ \251

3. Confirm that the cooling fans are turning. If
the fans are not turning, stop the engine im-
mediately and have it checked.
Petrol-powered vehicles
Diesel-powered vehicles A- Cooling fans
B- Radiator cap
C- Reserve tank lid
D- Reserve tank cap
*: Front of the vehicle
WARNING
l Be
careful not to get your hands or
clothes caught in the cooling fans. 4. After
the engine coolant temperature has drop-
ped to the normal temperature, stop the engine. 5. Check the coolant level in the reserve tank.
Petrol-powered vehicles
The

reserve tank lid (C) is equipped with a
dipstick.

Remove the dipstick and wipe it with a clean
cloth. Reinsert the dipstick as far as it goes.
Remove the dipstick and read the coolant lev-
el, which should always be within the range
indicated.
FULL
LOW WARNING
l If
there is none, make sure that the en-
gine has cooled down before removing
the radiator cap (B), because hot steam
or boiling water otherwise will gush from
the filler port and may scald you.
Diesel-powered vehicles
The
coolant level in this tank should be kept
between the “LOW” and “FULL” marks.
FULL
LOW WARNING
l If
there is none, make sure that the en-
gine has cooled down before removing
the reserve tank cap (D), because hot
steam or boiling water otherwise will
gush from the filler port and may scald
you.
6. Add
coolant to the radiator and/or reserve tank if necessary. (Refer to the “Mainte-
nance” section.) For emergencies
6-05 6
Presented by http://mmc-manuals.ru/ \251

CAUTION
l
Do not add coolant while the engine is
hot. Suddenly adding cold coolant could
damage the engine. Wait for the engine to
cool down, then add coolant a little at a
time.
7. Examine
the radiator hoses for coolant leak- age and the drive belt for looseness or damage.
If there is anything wrong with the cooling
system or drive belt, we recommend you to
have it checked and repaired. Tools and jack
E00800900864
Storage
The tools and jack are stored under the third seat.
The

storage location of the tools and jack should be
remembered in case of an emergency. 1- Jack
2-

Tools Tools
E00801900858 1- Wheel nut wrench
2-

Bar
3- Towing hook
Jack E00802000436
To remove 1. Stow
the third seat (Refer to “Stowing the
third seat” on page 2-13.)
2. Raise the luggage floor board. For emergencies
6-06
6
Presented by http://mmc-manuals.ru/ \251