2010 Lancia Musa Rear light

123
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
SNOW CHAINS
Use of snow chains should be in com-
pliance with local regulations.
The snow chains may be applied only
onto the front wheel tyres (drive
wheels). Use of Lineaccessori Lancia
snow chains is recommended.
Check the tension of the chains after
the first few metres have been driven.
IMPORTANT Snow chains cannot be
fitted on the space saver wheel. In
case of puncture to a front tyre, re-
place a rear wheel using the space
saver spare and fit the normal size
wheel on the front axle. In this way,
you can fit snow chains on the two
front wheels.
The tyres which are suitable for fitting snow chains and the type
of chain which can be used are shown in the table above. Follow
indications carefully.
Keep your speed down when snow chains are fitted. Do not
exceed 50 km/h. Avoid potholes, steps and pavements and
also avoid driving long distances on roads not covered with
snow in order to prevent damaging the car and the roadbed.
Tyres suitable for fitting Chain typesnow chains to be used
185/65 R14 86T
195/60 R15 88T
Chains cannot be fitted on
205/50 R16 87V tyres.
WARNING
Normal size snow chains
with maximum protrusion beyond tyre
profile equal to 12 mm.

124
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
CAR INACTIVITY
If the car is to be left inactive for
longer than a month, the following
precautions should be noted:
❒park the car in covered, dry and if
possible well-ventilated premises;
❒engage a gear;
❒check that the handbrake is not
engaged;
❒disconnect the negative battery
terminal and check battery charge.
Repeat this check once every three
months during storage. Recharge
the battery if the optical indicator
shows a dark colour without the
central green area;❒clean and protect the painted parts
using protective wax;
❒clean and protect the shiny metal
parts using special compounds
readily available;
❒sprinkle talcum powder on the rub-
ber windscreen and rear window
wiper blades and lift them off the
glass;
❒slightly open the windows;
❒cover the car with a fabric or per-
forated plastic terrapin. Do not use
compact plastic sheets which do not
allow humidity to evaporate from
the surface of the car.❒inflate tyres to a pressure of +0,5
bar above the normal specified
pressure and check it at intervals;
❒if you don’t disconnect the battery
from the electric system, check its
charge every month and recharge it
if the optical indicator shows a dark
colour without the central green
area;
❒do not drain the engine cooling sys-
tem.

125
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
WARNING LIGHTS AND MESSAGES
GENERAL WARNINGS..................................... 126
LOW BRAKE FLUID LEVEL ........................... 126
HANDBRAKE APPLIED.................................... 126
AIRBAG FAILURE............................................ 126
HOT ENGINE COOLANT............................... 127
LOW BATTERY CHARGE ............................... 127
LOW ENGINE OIL PRESSURE.............................128
EXHAUSTED OIL ........................................... 128
“DUALDRIVE” ELECTRIC POWER
STEERING SYSTEM ........................................ 129
DOOR OPEN .................................................... 129
SEAT BELT REMINDER....................................... 129
EBD FAILURE ................................................. 129
INJECTION SYSTEM FAILURE....................... 129
EOBD ENGINE CONTROL SYSTEM
FAILURE.......................................................... 129
FRONT PASSENGER AIRBAG DEACTIVATED.. 130
ABS FAILURE .................................................. 131
FUEL RESERVE .............................................. 131
GLOW PLUGS ................................................. 131GLOW PLUG FAILURE................................... 131
WATER IN DIESEL FUEL FILTER ................ 131
LANCIA CODE PROTECTION SYSTEM
FAILURE ......................................................... 132
REAR FOG LIGHTS ......................................... 132
GENERIC INDICATION ................................... 132
WORN BRAKE PADS ...................................... 133
OBSTRUCTED PARTICULATE TRAP ............. 133
SIDE, TAILLIGHTS AND DIPPED BEAM
HEADLIGHTS .................................................. 133
FOLLOW ME HOME ....................................... 133
FOG LIGHTS .................................................. 133
LEFT-HAND DIRECTION INDICATOR .......... 134
RIGHT-HAND DIRECTION INDICATOR ........ 134
“DUALDRIVE” ELECTRIC POWER
STEERING SYSTEM ON .................................. 134
CRUISE CONTROL ........................................ 134
MAIN BEAM HEADLIGHTS ............................. 134
POSSIBLE ICE ON ROAD ................................ 134
LIMITED RANGE ............................................. 134

129
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
“DUALDRIVE”
ELECTRIC POWER
STEERING SYSTEM
(red)
This warning light comes on when the
ignition key is turned to MAR, but it
should go off after a few seconds.
The electric power steering system
will not work when the warning light
is on and considerably more effort is
needed on the steering wheel. The car
can still be steered: go to a Lancia
Dealership.
The display will show the dedicated
message.
g
DOOR OPEN (red)
On certain versions the
warning light turns on
when one or more doors or
the tailgate are not properly closed.
The display will show a dedicated
message.
A buzzer will sound when doors/
tailgate are open and the car is mov-
ing.
´
SEAT BELTS
REMINDER (red)
(for versions/markets,
where provided)
The warning light on the display will
light up when the car is moving and
the driver’s seat belt is not correctly
fastened. The warning light will blink
and a buzzer will sound if the front
seat belts are not correctly fastened.
The buzzer of the SBR (Seat Belt Re-
minder) system may only be switched
off by a Lancia Dealership. The sys-
tem can be reactivated by means of
the setup menu.
<
>
EBD FAILURE
(red)
(amber)
Warning lights xand>lit at the
same time with the engine running in-
dicates an EBD system failure or that
the system is not available. Early
locking of the rear wheels may occur
in the event of violent braking caus-
ing the car to swerve. Drive very care-
fully to a Lancia Dealership to have
the system inspected.
The display will show the dedicated
message.
x
INJECTION SYSTEM
FAILURE
(Multijet versions
- amber)
SYSTEM FAILURE EOBD
ENGINE CONTROL
(petrol versions - amber)
Injection system failure
When the ignition key is moved to
MAR, the warning light turns on and
should go out as soon as the engine is
started.
If the warning light stays on or turns
on when travelling, means a fault in
the supply/ignition system which
could cause high emissions at the ex-
haust, possible lack of performance,
poor handling and high consumption
levels.
The display will show a dedicated
message.
In these conditions, you may continue
travelling at moderate speed without
demanding excessive effort from the
engine. Go to a Lancia Dealership as
soon as possible.
U

132
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
GENERIC INDICATION
(amber)
The warning light turns on
in the following circum-
stances.
Exterior lights failure
The warning light will come on (some
versions only) when a fault to one of
the following lights is detected:
– side/taillights
– brake lights (excluding third brake
light)
– rear fog lights
– direction indicators
– number plate lights.
The fault may be caused by: one or
more burnt lamps, a blow protection
fuse or interruption of the electrical
connection.
The display will show the dedicated
message.
Obstructed particulate trap
(for versions/markets, where provided)
The warning light turns on when the
diesel particulate trap is clogged and
the driving conditions do not enable
to activate automatically the regener-
ation procedure.
è
To allow the regeneration procedure,
keep the car running until the warn-
ing light turns off.
The display will show a dedicated
message.
Engine oil pressure sensor
failure
The warning light turns on when fail-
ure is detected in parking sensors. Go
to a Lancia Dealership as soon as pos-
sible.
Rain/dusk sensor failure
The warning light comes on when a
dusk/rain sensor failure is detected.
Go to a Lancia Dealership as soon as
possible.
The display will show a dedicated
message.
Fuel cut-off switch tripped
The warning light comes on when the
fuel cut-off switch trips.
The display will show a dedicated
message. LANCIA CODE
PROTECTION SYSTEM
FAILURE (amber)
Turning the key to MAR, the
warning light flashes once and then
goes off.
If with the ignition key at MAR, the
warning light stays on, this indicates
a possible failure (see “Lancia Code
system” in section “Dashboard and
controls”).
IMPORTANT The turning on at the
same time of the Uand
Ywarning
lights indicates a failure of the Lancia
CODE system.
If with the engine running the warn-
ing light
Yflashes, this means that
the car is not protected by the engine
immobilizer device (see “Lancia Code
system” in section “Dashboard and
controls”).
Contact Lancia Dealership to have all
the key stored.
Y
REAR FOG LIGHTS
(amber)
The warning light comes on
when the rear fog lights are on.
4

143
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
The spare wheel is specific
for your car. Do not use it
on cars of different models. Do not
use spare wheels of different mod-
els on your car. The space saver
spare wheel must only be used in
case of emergency. Use only for as
long as strictly necessary and drive
at a speed slower than
80 km/h. An orange label is affixed
on the spare wheel summarising
instructions and limitations for
use. Never remove or cover the la-
bel. Never apply a wheel cup on a
space saver spare. The following
information is provided in four
languages on the label: Warning!
Suitable for temporary use only!
80 km/h max! Replace with a
standard wheel as soon as possi-
ble. Do not cover this label.
WARNING
The driving features of the
car may change when a
space saver spare wheel is fitted.
Avoid sudden acceleration and
braking, sudden steering and fast
cornering. The total life of a space
saver spare wheel is approxi-
mately 3000 km, after which it
must be replaced by another wheel
of the same type. Never install a
traditional tyre on a space saver
spare wheel rim. Repair and refit
the standard wheel as soon as pos-
sible. Only one space saver spare
can be used at a time. Do not ap-
ply grease to the bolt threading be-
fore assembly: the bolts could come
loose unexpectedly.
WARNING
The jack may only be used
to replace wheels on the
car which it equips or other cars of
the same model. Never use the jack
for other purposes, such as lifting
other car models. Never use the
jack to carry out repairs under the
car. Incorrect positioning of the
jack may cause the car to fall. Do
not use the jack for loads higher
than those shown on the label.
Snow chains cannot be fitted on a
space saver spare wheel. There-
fore, if a front wheel (drive wheel)
is punctured and you need to use
snow chains, swap with a rear
wheel. In this way, you will have
two normal wheels on the front on
which you can fit snow chains and
solve the emergency.
WARNING

145
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
fig. 11L0D0397m
fig. 12L0D0163m
❒for cars fitting alloy rims, remove
the hub cap using the screwdriver
provided levering in groove E-
fig. 11, as shown in the figure;
❒loosen the bolts of the wheel to be
replaced by about one turn with the
wrench provided E-fig. 12; if the
car is fitted with alloy rims, shake
the car to facilitate removing the
rim from the wheel hub;❒operate the device F- fig. 13to ex-
pand the jack, until the groove G
on the upper part of the jack is
correctly inserted on the lower
edgeHof the body at indication I
(at approximately 60 cm from the
front wheel centre or 80 cm from
the rear wheel centre);
❒warn anybody nearby that the car
is about to be lifted. They must
stay clear and not touch the car
until it is back on the ground;❒fit the handle L-fig. 13to operate
the jack and lift the car until the
wheel to be changed is several cen-
timetres off the ground;
❒for versions with wheel cap, remove
the wheel cap after loosening the
three fastening bolts and finally
loosen the fourth bolt and extract
the wheel;
❒for versions with snap fitted wheel
cup, remove the cup being careful
not to damage it;
❒make sure the contact surfaces be-
tween space saver spare wheel and
hub are clean so that the fastening
bolts will not come loose;
L0D0164mfig. 13

147
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
Versions with alloy rims
❒Check that the hub contact sur-
faces are clean;
❒fit the normal wheel centring it on
the pins, lead in the fastening
screws and tighten them using the
wrench provided;
❒lower the car and remove the jack;
❒using the wrench provided, fully
tighten the bolts in the sequence
shown in fig. 15.
❒snap fit the wheel cup on the hub.When you have finished
❒stow the spare wheel in the space
provided in the boot;
❒fit the jack partially open in its
box forcing it lightly to prevent it
from vibrating when travelling;
❒put the tools back into their places
in the container;
❒arrange the container and tools in
the spare wheel and secure the fas-
tening device;
❒rearrange the preformed boot
cover correctly. WHEN NEEDING
TO CHANGE A
BULB
GENERAL INSTRUCTIONS
❒When a bulb is not working, check
that the corresponding fuse is in-
tact before replacing it: refer to the
“If a fuse blows” paragraph in this
chapter for fuse location.
❒before changing a bulb check the
contacts for oxidation;
❒burnt bulbs must be replaced by
others of the same type and power;
❒always check the height of the
headlight beam after changing a
bulb.
Halogen lamps must be
handled holding the metal-
lic part only. Touching the
transparent part of the bulb
with your fingers may reduce the in-
tensity of the emitted light and even
compromise duration of the lamp it-
self.