2010 Lancia Delta height

46GETTING TO KNOW YOUR CAR
Height adjustment fig. 16
Operate lever C to raise or lower the rear part of the seat
cushion to improve comfort.
Lumbar adjustment (driver’s seat) fig. 16
for lumbar adjustment, turn knob D.
ELECTRICALLY ADJUSTABLE FRONT SEATS
fig. 17
(for versions/markets, where provided)
Adjustment is possible when the ignition key is at MAR or
within 1 minute with ignition key at STOP or removed.
When opening one of the front doors, it is possible to ad-
just the seat on the side of the door opened for about 3
minutes or until closing the door.
Seat adjustment controls are the following:
Multifunction control A:
❍to adjust height;
❍to move seat backwards or forwards.
Multifunction control B:
❍back rest angle adjustment;
❍lumbar adjustment.Seat warming fig. 17
(for versions/markets, where provided)
With ignition key at MAR, press buttons
Cto switch the
seat warming on/off.
The led on the button will light up when the function is
on.
fig. 17L0E0009m
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 46

48GETTING TO KNOW YOUR CAR
HEAD RESTRAINTS
FRONT fig. 19
The height of the head restraints can be adjusted as fol-
lows.
❍Upward adjustment: raise the head restraint until you
hear it click.
❍Downward adjustment: press button A and lower the
head restraint.
fig. 19L0E0011m
Height-adjustable head restraints:
❍To adjust upwards: Press button C and lift the head
restraint until the lock clicks.
❍To adjust downwards: press button C and lower the
head restraint.
IMPORTANT Rear seat passengers should always set the
head restraints in “fully drawn out” position.
Perform these operations only when the car
is stationary and the engine is not running.
The head restraints must be adjusted so that
they support your head and not your neck. Only then
do they fulfil their protective action. To optimise
head restraint protective action, adjust the backrest
upright and keep your head as close as possible to
the head restraint.
REAR fig. 19
(for versions/markets, where provided)
Depending on the versions, rear head restraints can be
"fixed" or height adjustable type.
001-142 Delta 3ed gb 30-11-2009 11:21 Pagina 48

94GETTING TO KNOW YOUR CAR
fig. 62L0E0220m
DOUBLE LOAD COMPARTMENT
(MAGIC BACK BOX)
(for versions/markets, where provided)
In addition to reclining seats the car can also be equipped
with an adjustable load platform with two different heights
in order to even the load and adjust the luggage com-
partment capacity.
Keeping the load platform in the upper position makes it
possible for the space created underneath to be used as
another compartment that can be used to store more frag-
ile or smaller objects.
To access the compartment under the load compartment,
lift up shelf A holding it with your hands and put the de-
sired objects inside.
IMPORTANT Movements of the load platform may take
place if it is in a central position in relation to the lugga-
ge compartment.To place shelf A at the level of the floor
(fully lowered) fig. 63:
❍always turn the elements C - Fig. 62 so that they are
always turn the elements C - Fig. 62 so that they are
in a vertical position against the seat backrest;
❍grip the handle B and lift up shelf A by around 45°
(point 1);
❍pull the shelf in a horizontal direction towards itself
until the end of travel position (point 2);
❍push the shelf downwards gently until point 3 is rea-
ched (fully lowered);
❍accompany the shelf to the “fully lowered” position
(point 4).
To move shelf A from the fully lowered position to
the highest position Fig. 64:
❍pull handle B from point 1 and raise shelf A by around
45°;
❍pull the shelf upwards to point 2 and leave it resting
on the side supports D;
❍pull the shelf towards itself as far as point 3 (fully
forwards);
❍let the shelf fall at point 4 in the "fully raised" position.
To extract the spare wheel:
❍pull the load shelf upwards using handle B;
❍lift up the load compartment carpet;
❍extract the tape and hook for the carpet and attach it
to the boot upper seal.
001-142 Delta 3ed gb 30-11-2009 11:22 Pagina 94

SAFETY151
2
All restraint devices must bear the type-approval data
along with the control mark on a label that must be firm-
ly secured to the child seat and must never be removed.
When over 1.50 m in height, from the point of view of
restraint systems, children are considered as adults and
have to wear the standard seat belts. Lineaccessori Lan-
cia includes child seats for each weight group.
These devices are recommended and have been specifi-
cally designed for Lancia cars.
GROUP 0 and 0+
Babies up to 13 kg must be carried facing backwards on
a cradle seat, which, supporting the head, does not induce
stress on the neck in the event of sharp deceleration.
The cradle is restrained by the car seat belts, as shown in
fig. 4 and in turn it must restrain the child with its own
belts.
GROUP 1
Children from 9 kg to 18 kg in weight can be carried fac-
ing forwards.
fig. 4L0E0272m
143-164 Delta 4ed gb 12-02-2010 10:20 Pagina 151

152SAFETY
GROUP 2
Children from 15 to 25 kg may use the car seat belts di-
rectly fig. 4.
The child seat is only needed to position the child correctly
with respect to the belts so that the diagonal section cross-
es the child’s chest and never the neck and is snug on the
hips not the abdomen.
GROUP 3
For children between 22 kg and 36 kg, there are boost-
ers allowing the seatbelt to fit correctly.Figure 4 shows proper child seat positioning on the rear
seat. Children over 1.50 m in height can wear seat belts
like adults. Below is a summary of the safety rules to be
followed when carrying children.
1) The recommended position for installing child seats
is on the rear seat, as it is the most protected area in
the event of a crash.
2) If the passenger’s air bag is deactivated always check
the amber warning light “is lit on the instrument pan-
el to make sure that it has actually been deactivated.
3) Carefully follow the instructions supplied with the child
restraint system which are mandatory by law. Keep the
instructions in the car along with the other papers and
this handbook. Do not use child seats without in-
structions.
4) Always check the seat belt is well fastened by pulling
the webbing.
5) Only one child is to be strapped to each retaining sys-
tem; never carry two children using one child seat.
6) Always check the seat belts do not rest on the child’s
throat.
7) While travelling, do not let the child sit incorrectly or
release the belts.
8) Never carry children on your lap, even newborns. No-
one, however strong, can hold a child in the event of
an accident.
9) In the event of an accident, replace the child’s seat with
a new one.
The figures are indicative for assembly pur-
poses only. To install the child restraint, re-
fer to the instructions supplied with the same.
Child seats with Isofix attachments are available
for a safe anchoring to the seat without using the car
seat belts.
143-164 Delta 4ed gb 12-02-2010 10:20 Pagina 152

238CARE AND MAINTENANCE
SPRAY NOZZLES
Windscreen washer fig. 7
If the jet of fluid is inadequate, firstly check that there is
fluid in the reservoir: see “Checking fluid levels” in this
section).
Then check that the nozzle holes are not clogged, if nec-
essary use a needle.
The windscreen jets are directed by adjusting the angle
of the nozzles.
Fluid jets should be directed at about 1/3 height from
the window upper edge.
IMPORTANT In versions with a sunroof, make sure that
the sunroof is closed before operating the front jets.
fig. 7L0E0099m
Rear window wiper fig. 8
Rear window washer jets are fixed.
The nozzle holder is on the rear window.
fig. 8 L0E0100m
215-242 Delta 3ed gb 11-11-2009 12:14 Pagina 238

252TECHNICAL DATA
WHEELS
RIMS AND TYRES
Pressed steel or alloy rims. Tubeless radial carcass tyres.
All approved tyres are listed in the Log Book.
IMPORTANT In the event of discrepancies between the
information provided on this “Owner’s handbook” and
the “Log book”, consider the specifications shown in the
log book only.
Respect the prescribed size to ensure safety of the car in
movement. Fit tyres of the same make and type on all
wheels.
IMPORTANT Do not use inner tubes with Tubeless tyres.
SMALL SPARE WHEEL
Pressed steel rim Tubeless tyre.
WHEEL GEOMETRY
Front wheel toe-in: –1
±1 mm
Rear wheel toe-in: 2
± 2 mm
The values refer to the car in running order.READING TYRE MARKINGS fig. 5
Example: 195/55 R 16 91 V
195 = Nominal width (S, distance in mm between
sidewalls).
55 = Height/width ratio (H/S) in percentage.
R = Radial tyre.
16 = Rim diameter in inches (Ø).
91 = Load rating (capacity).
V = Maximum speed rating.
fig. 5L0E0120m
243-266 Delta 3ed gb 11-11-2009 12:16 Pagina 252

256TECHNICAL DATA
fig. 6
L0E0101m
DIMENSIONS
452010172700
(*) measurements may vary slightly according to rim size1499 (*)15381531
Luggage compartment capacity:
Unladen luggage compartment capacity (V.D.A. standards): ............380 dm
3
Maxi capacity ....................................................................................465 dm3
Dimensions are expressed in mm and refer to the vehicle fitted with standard
tyres. The height refers to the vehicle unladen.
1797803
ABCDEFGH
243-266 Delta 3ed gb 11-11-2009 12:16 Pagina 256