2010 JEEP COMMANDER driver seat adjustment

UNDERSTANDING THE FEATURES OF YOUR VEHICLE
CONTENTS
Mirrors .............................. 82
▫ Inside Day/Night Mirror ................ 82
▫ Automatic Dimming Mirror — If Equipped . . . 82
▫ Outside Mirrors ...................... 83
▫ Exterior Mirrors Folding Feature .......... 83
▫ Outside Automatic Dimming Mirrors
— If Equipped ....................... 84
▫ Power Mirrors ....................... 84
▫ Heated Mirrors — If Equipped ............ 84▫
Illuminated Vanity Mirrors — If Equipped . . . 85
▫ Sun Visor Extension — If Equipped ........ 85
 uconnect™ phone — If Equipped ........... 85
 Voice Recognition (VR) System — If Equipped . . 85
 Seats ............................... 85
▫ Front Manual Seat Adjustment ............ 86
▫ Front Seat Adjustment — Recline .......... 86
▫ Manual Lumbar Support Adjustment ....... 87
▫ Eight–Way Driver’s Power Seat ........... 88
3

WARNING!
Do not ride with the seatback reclined so that the seat
belt is no longer resting against your chest. In a
collision you could slide under the seat belt and be
seriously or even fatally injured. Use the recliner
only when the vehicle is parked.
Manual Lumbar Support Adjustment
The manual lumbar support adjustment lever is located
on the right side of the driver’s seatback and on the left
side of the passenger’s seatback (if equipped). Moving
the lumbar control lever fore and aft increases or de-
creases the lumbar support.
Manual Lumbar Control
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87

Eight–Way Driver’s Power Seat
The driver’s power seat switches are located on the
outboard side of the driver’s seat. The bottom switch
controls up/down, forward/rearward, and tilt adjust-
ment. The top switch controls the seatback recline adjust-
ment.WARNING!
Adjusting a seat while the vehicle is moving is
dangerous. The sudden movement of the seat could
cause you to lose control. The seat belt might not be
properly adjusted and you could be injured. Adjust
any seat only while the vehicle is parked.
CAUTION!
Do not place any article under any seat as it may
cause damage to the seat controls.
Four-Way Passenger’s Power Seat — If Equipped
The front passenger’s power seat switches are located on
the outboard side of the passenger seat. The bottom
switch controls forward/rearward adjustment. The top
switch controls the seatback recline adjustment.
Power Seat Switches
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Easy Entry/Exit Seat
This feature provides automatic driver’s seat positioning
which will enhance driver mobility out of and into the
vehicle.
There are two possible Easy Entry/Exit adjustments
available:
•The seat cushion will move rearward approximately
2.5 in (60 mm), if the starting position of the seat is
greater than or equal to 2.67 in (68 mm) forward of the
rear seat stop when the key is removed from the
ignition switch. The seat will then move forward
approximately 2.5 in (60 mm) when the key is placed
into the ignition and turned out of the LOCK position.
•The seat will move to the position located 0.3 in
(8 mm) forward of the rear stop if the starting position
is between 0.9 to 2.67 in (23 to 68 mm) forward of the
rear stop when the key is removed from the ignition
switch. The seat will move forward to the memory/driving position when the key is placed into the
ignition, and turned out of the LOCK position toward
the ACC/ON position.
The Easy Entry/Exit feature will be automatically dis-
abled if the seat is already positioned closer than 0.9 in
(23 mm) forward of the rear stop. At this position, there
is no benefit to the driver by moving the seat for Easy
Exit/Entry.
Each stored memory setting will have an associated Easy
Entry/Exit position.
NOTE: The Easy Entry/Exit feature is not enabled
when the vehicle is delivered from the factory. The Easy
Entry/Exit feature is enabled (or later disabled) through
the programmable features in the Electronic Vehicle
Information Center (EVIC). Refer to Electronic Vehicle
Information Center (EVIC) — Customer-Programmable
Features in Section 4 for more information.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE:The numbers on the temperature dial represent
a comfort setting when the Mode knob is set to AUTO,
and not the actual air temperature. Turn the mode control (on the right) knob to AUTO, and
place the blower control (on the left) to either LO AUTO
or HI AUTO. The LO AUTO position should be used for
front seat occupants only. The HI AUTO position should
be used when more airflow is desired, or when rear seat
occupants are present. Dial in the comfort setting you
would like the system to maintain by rotating the driver’s
or passenger’s control knob. Once the comfort level is
selected, the system will maintain that level automati-
cally using the heating system. Should the desired com-
fort level require air conditioning, the system will auto-
matically make the adjustment.
Automatic Temperature Controls (ATC)
4
UNDERSTANDING YOUR INSTRUMENT PANEL 227