2010 INFINITI QX56 remote control

ADP-2
DTC Logic ...............................................................35
Diagnosis Procedure .............................................35
B2117 ADJ PEDAL MOTOR .............................36
Description ..............................................................36
DTC Logic ...............................................................36
Diagnosis Procedure .............................................36
B2118 TILT SENSOR ........................................38
Description ........................................................... ...38
DTC Logic ...............................................................38
Diagnosis Procedure .............................................38
B2120 ADJ PEDAL SENSOR ...........................40
Description ........................................................... ...40
DTC Logic ...............................................................40
Diagnosis Procedure .............................................40
B2126 DETENT SW ...........................................42
Description ........................................................... ...42
DTC Logic ...............................................................42
Diagnosis Procedure .............................................42
B2128 UART COMMUNICATION LINE ............44
Description ........................................................... ...44
DTC Logic ...............................................................44
Diagnosis Procedure .............................................44
POWER SUPPLY AND GROUND CIRCUIT .....46
BCM ........................................................................ ...46
BCM : Diagnosis Procedure ...................................46
DRIVER SEAT CONTROL UNIT ........................... ...47
DRIVER SEAT CONTROL UNIT :
Diagnosis Procedure .............................................
47
DRIVER SEAT CONTROL UNIT : Special Repair
Requirement ........................................................ ...
48
AUTOMATIC DRIVE POSITIONER CONTROL
UNIT ....................................................................... ...
48
AUTOMATIC DRIVE POSITIONER CONTROL
UNIT : Diagnosis Procedure ............................... ...
48
AUTOMATIC DRIVE POSITIONER CONTROL
UNIT : Special Repair Re quirement .......................
48
SLIDING SWITCH ..............................................50
Description ........................................................... ...50
Component Function Check .................................50
Diagnosis Procedure .............................................50
Component Inspection ............................................51
RECLINING SWITCH ........................................53
Description ........................................................... ...53
Component Function Check .................................53
Diagnosis Procedure .............................................53
Component Inspection ............................................54
LIFTING SWITCH (FRONT) ..............................56
Description ........................................................... ...56
Component Function Check .................................56
Diagnosis Procedure .............................................56
Component Inspection ......................................... ...57
LIFTING SWITCH (REAR) ................................59
Description ........................................................... ...59
Component Function Check ..................................59
Diagnosis Procedure ..............................................59
Component Inspection ............................................60
TILT SWITCH ....................................................62
Description ........................................................... ...62
Component Function Check ..................................62
Diagnosis Procedure ..............................................62
Component Inspection ............................................63
PEDAL ADJUSTING SWITCH ..........................65
Description ........................................................... ...65
Component Function Check ..................................65
Diagnosis Procedure ..............................................65
Component Inspection ............................................67
SEAT MEMORY SWITCH .................................68
Description ..............................................................68
Component Function Check ..................................68
Diagnosis Procedure ..............................................68
Component Inspection ............................................69
DOOR MIRROR REMOTE CONTROL
SWITCH .............................................................
70
CHANGEOVER SWITCH ....................................... ...70
CHANGEOVER SWITCH : Description ..................70
CHANGEOVER SWITCH : Component Function
Check ......................................................................
70
CHANGEOVER SWITCH : Diagnosis Procedure ...70
CHANGEOVER SWITCH : Component Inspec-
tion ..........................................................................
72
MIRROR SWITCH .................................................. ...72
MIRROR SWITCH : Description .............................72
MIRROR SWITCH : Component Function Check ...72
MIRROR SWITCH : Diagnosis Procedure ..............72
MIRROR SWITCH : Component Inspection ...........74
POWER SEAT SWITCH GROUND CIRCUIT ...76
Diagnosis Procedure ..............................................76
DETENTION SWITCH .......................................77
Description ........................................................... ...77
Component Function Check ..................................77
Diagnosis Procedure ..............................................77
FRONT DOOR SWITCH (DRIVER SIDE) .........79
Description ........................................................... ...79
Component Function Check ...................................79
Diagnosis Procedure ...............................................79
Component Inspection ............................................80
SLIDING SENSOR ............................................81
Description ..............................................................81
Component Function Check ..................................81
Diagnosis Procedure ..............................................81
Revision: April 20092010 QX56

ADP-4
AUTOMATIC DRIVE POSITIONER CON-
TROL UNIT ......................................................
175
Removal and Installation ..................................... ..175
SEAT MEMORY SWITCH ...............................176
Removal and Installation ..................................... ..176
DOOR MIRROR REMOTE CONTROL
SWITCH ............................................................
177
Removal and Installation .......................................177
PEDAL ADJUSTING MOTOR ........................ ..178
Removal and Installation .......................................178
TILT SWITCH ................................................. ..179
Removal and Installation .......................................179
Revision: April 20092010 QX56

ADP-12
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
AUTOMATIC DRIVE POSITIONER SYSTEM : System Description
INFOID:0000000005147427
OUTLINE
The system automatically moves the driver seat, pedal assembly, steering wheel and door mirror position by
the driver seat control unit and the automatic drive posit ioner control unit. The driver seat control unit corre-
sponds with the automatic drive positioner control unit by UART communication.
AUTOMATIC DRIVE POSITIONER SYSTEM : Component Parts LocationINFOID:0000000005147426
Function Description
Manual function The driving position (seat, pedal assembly, steering wheel and door mirror position)
can be adjusted by using the power seat switch, pedal adjusting switch, ADP steering
switch or door mirror remote control switch.
Memory function The seat, pedal assembly and outside mirror move to the stored driving position by
pressing seat memory switch (1 or 2).
Entry/Exit assist function Exit On exit, the seat moves backward and the steering wheel moves upward.
Entry
On entry, the seat and steering wheel return from exiting position to the previous driv-
ing position.
ALJIA0347ZZ
1. A. Automatic drive positioner control
unit M33, M34
B. Pedal adjusting motor assembly
E109, E110 2. A. Steering column
B. Key switch and ignition knob
switch M12
C. BCM M18, M19, M20 (view with
instrument panel removed) 3. A. Door mirror remo
te control switch
D10
B. Seat memory switch D5
Revision: April 20092010 QX56

AUTOMATIC DRIVE POSITIONER SYSTEMADP-13
< FUNCTION DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
AUTOMATIC DRIVE POSITIONER SYSTEM : Component DescriptionINFOID:0000000005147428
CONTROL UNITS
INPUT PARTS
Switches
4. Pedal adjusting switch M96 5 . A. Door mirrror LH D4, RH D107
B. Front door switch LH B 6. A. A/T selector lever
B. A/T shift selector (park position
switch) M203
7. A. Sliding motor LH B204 (driver seat view), reclining motor LH B205, lift-
ing motor (front) B2 06, lifting motor
(rear) B207
B. Driver seat control unit B202,
B203
C. Power seat switch LH B208 8. A. ADP steering switch M16
B. Tilt sensor M85 and tilt motor M86
Item Function
Driver seat control unit • Main unit of automatic drive positioner system
• It is connected to the CAN.
• It communicates with the automatic drive positioner control unit via UART com-
munication.
Automatic drive positioner control unit • It communicates with the driver seat control unit via UART communication.
• Perform various controls with the instructions of driver seat control unit.
• Perform the controls of the pedal adjusting, steering wheel, door mirror and the
seat memory switch.
BCM Transmit the following status to the driver seat control unit via CAN communication.
• Front door LH: OPEN/CLOSE
• Ignition switch position: ACC/ON
• Door lock: UNLOCK (with Intelligent Key or remote keyless entry request switch
operation)
• Key ID
• Key switch: Insert/Pull out Intelligent Key
• Starter: CRANKING/OTHER
Combination meter Transmit the vehicle speed signal to the driver seat control unit via CAN communi-
cation.
AV control unit The setting change of auto drive positioner system can be performed on the display.
A/T shift selector (park position switch) Transmit the shift position signal (P range) to the driver seat control unit.
Item Function
Key switch and ignition knob switch The key switch is installed to detect the key inserted/removed status.
Front door switch LH Detect front door (driver side) open/close status.
A/T shift selector (park position switch) Detect the P range position of A/T selector lever.
Set switch The registration and system setting can be performed with its operation.
Seat memory switch 1/2 The registration and operation can be performed with its operation.
Power seat switch The following switch is installed.
• Reclining switch
• Lifting switch (front)
• Lifting switch (rear)
• Sliding switch
The specific parts can be operated with the operation of each switch.
Pedal adjusting switch The following switch is installed.
• Pedal forward
• Pedal backward
The specific parts can be operated with the operation of each switch.
Revision: April 20092010 QX56

ADP-14
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
Sensors
OUTPUT PARTS
MANUAL FUNCTION
ADP steering switchThe following switch is installed.
• Steering wheel UP
• Steering wheel down
The specific parts can be operated with the operation of each switch.
Door mirror remote control switch The following switch is installed.
• Mirror switch
• Changeover switch
The specific parts can be operated with the operation of each switch.
Item
Function
Item Function
Door mirror sensor (LH/RH) Detect the up/down and left/right position of outside mirror face.
Pedal adjusting sensor Detect the forward/backward position of pedal assembly.
Tilt sensor Detect the upward/downward position of the steering wheel.
Lifting sensor (front) Detect the up/down position of seat lifting (front).
Lifting sensor (rear) Detect the up/down position of seat lifting (rear).
Reclining sensor Detect the tilt of seatback.
Sliding sensor Detect the front/rear position of seat.
Item Function
Door mirror motor (LH/RH) Move the outside mirror face upward/downward and left/right.
Pedal adjusting motor Move the pedal assembly forward/backward.
Tilt motor Move the steering wheel upward/downward.
Lifting motor (front) Move the seat lifting (front) upward/downward.
Lifting motor (rear) Move the seat lifting (rear) upward/downward.
Reclining motor Tilt and raise up the seatback.
Sliding motor Slide the seat forward/backward.
Seat memory indicator Illuminates or flashes according to the registration/operation status.
Revision: April 20092010 QX56

AUTOMATIC DRIVE POSITIONER SYSTEMADP-15
< FUNCTION DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
MANUAL FUNCTION : System DiagramINFOID:0000000005147429
MANUAL FUNCTION : System DescriptionINFOID:0000000005147430
OUTLINE
The driving position (seat, pedal assembly, steering wheel and door mirror position) can be adjusted manually
with power seat switch, pedal adjusting switch, ADP st eering switch and door mirror remote control switch.
OPERATION PROCEDURE
1. Turn ignition switch ON.
2. Operate power seat switch, pedal adjusting switch, ADP steering switch or door mirror remote control
switch.
3. The driver seat, pedal assembly, steering wheel or door mirror operates according to the operation of each switch.
DETAIL FLOW
Seat
Adjustable pedals
ALJIA0236GB
Order Input Output Control unit condition
1 Power seat switch
(sliding, lifting, reclin-
ing)
—
The power seat switch signal is inputted to the driver seat control
unit when the power seat switch is operated.
2— Motors
(sliding, lifting, reclin-
ing)The driver seat control unit outputs signals to each motor accord-
ing to the power seat switch input signal.
Revision: April 20092010 QX56

ADP-16
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
Tilt steering wheel
Door Mirror
NOTE:
The door mirrors can be operated manually when ignition switch is in either ACC or ON position. The ignition
switch signal (ACC/ON) is transmitted from BCM to the driver seat control unit via CAN communication and
from the driver seat control unit to the automatic drive positioner control unit via UART communication.
OrderInput Output Control unit condition
1 Pedal adjusting switch —The pedal adjusting switch signal is input to the automatic drive
positioner control unit when the pedal adjusting switch is operat-
ed.
2—M oto r The automatic drive positioner control unit actuates the motor ac-
cording to the operation of the pedal adjusting switch signal from
the driver seat control unit.
3 Sensor
(forward, backward) —The automatic drive positioner control unit recognizes any oper-
ation limit of each actuator via each sensor and will not operate
the actuator anymore at that time.
Order
Input Output Control unit condition
1 ADP steering switch —The ADP steering switch signal is input to the automatic drive po-
sitioner control unit when the ADP steering switch is operated.
2—M oto r The automatic drive positioner control unit actuates the tilt motor
according to the operation of the ADP steering switch signal.
3 Sensor
(upward, downward) —The automatic drive positioner control unit recognizes any oper-
ation limit of each actuator via each sensor and will not operate
the actuator anymore at that time.
Order
Input Output Control unit condition
1 Door mirror remote
control switch —The door mirror remote control switch signal is inputted to the au-
tomatic drive positioner control unit when the door mirror remote
control switch is operated.
2— Motors
(Door mirror motor)The automatic drive positioner control unit actuates each motor
according to the operation of the door mirror remote control switch.
Revision: April 20092010 QX56

ADP-18
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
INPUT PARTS
Switches
Sensors
OUTPUT PARTS
MEMORY FUNCTION
Automatic drive positioner control unitOperates the specific motor with the signal from driver seat control unit, ADP steer-
ing switch or door mirror remote control switch.
BCM Recognizes the following status and transmits it to the driver seat control unit via
CAN communication.
• Ignition position: ACC/ON
Item
Function
Item Function
Power seat switch The following switch is installed.
• Reclining switch
• Lifting switch (front)
• Lifting switch (rear)
• Sliding switch
The specific parts can be operated with the operation of each switch.
Pedal adjusting switch The following switch is installed.
• Pedal forward
• Pedal backward
The specific parts can be operated with the operation of each switch.
ADP steering switch The following switch is installed.
• Steering wheel upward
• Steering wheel downward
The specific parts can be operated with the operation of each switch.
Door mirror remote control switch The following switch is installed.
• Mirror switch
• Changeover switch
The specific parts can be operated with the operation of each switch.
Item
Function
Pedal adjusting sensor Detect the forward/backward position of pedal assembly.
Tilt sensor Detect the upward/downward position of steering wheel.
Item Function
Door mirror motor (LH/RH) Move the outside mirror face upward/downward and left/right.
Pedal adjusting motor Move the pedal assembly forward/backward.
Tilt motor Move the steering wheel upward/downward.
Lifting motor (front) Move the seat lifter (front) upward/downward.
Lifting motor (rear) Move the seat lifter (rear) upward/downward.
Reclining motor Tilt and raise up the seatback.
Sliding motor Slide the seat forward/backward.
Revision: April 20092010 QX56