2010 INFINITI QX56 mirror

ADP-24
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
EXIT ASSIST FUNCTION : Component Description
INFOID:0000000005147440
CONTROL UNITS
INPUT PARTS
Switches
Sensors
OUTPUT PARTS
ENTRY ASSIST FUNCTION
1. A. Automatic drive positioner control unit M33, M34
B. Pedal adjusting motor assembly
E109, E110 2. A. Steering column
B. Key switch and ignition knob
switch M12
C. BCM M18, M19, M20 (view with
instrument panel removed) 3. A. Door mirror remo
te control switch
D10
B. Seat memory switch D5
4. Pedal adjusting switch M96 5 . A. Door mirrror LH D4, RH D107
B. Front door switch LH B 6. A. A/T selector lever
B. A/T shift selector (park position
switch) M203
7. A. Sliding motor LH B204 (driver seat
view), reclining motor LH B205, lift-
ing motor (front) B206, lifting motor
(rear) B207
B. Driver seat control unit B202,
B203
C. Power seat switch LH B208 8. A. ADP steering switch M16
B. Tilt sensor M85 and tilt motor M86
Item Function
Driver seat control unit • Operates the seat sliding motor for a constant amount.
• Driver seat control unit requests the operation of the tilt motor to the automatic
drive positioner control unit via UART communication.
Automatic drive positioner control unit Operates the tilt motor for a constant amount.
BCM Recognizes the following status and transmits it to the driver seat control unit via
CAN communication.
• Front door LH: OPEN/CLOSE
Item
Function
Front door switch LH Detect front door LH open/close status.
Item Function
Sliding sensor Detect the front/rear position of seat.
Tilt sensor Detect the up/down position of steering wheel.
Item Function
Sliding motor Slide the seat forward/backward.
Tilt motor Moves the steering wheel upward/downward.
Revision: April 20092010 QX56

AUTOMATIC DRIVE POSITIONER SYSTEMADP-25
< FUNCTION DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
ENTRY ASSIST FUNCTION : System DiagramINFOID:0000000005147441
ENTRY ASSIST FUNCTION : System DescriptionINFOID:0000000005147442
OUTLINE
The seat and steering wheel are in the exiting position when either following condition (A or B) is satisfied, the
seat and steering wheel return from exiting position to the previous driving position.
NOTE:
• This function is set to OFF before delivery (initial setting).
• Further information for the system setting procedure. Refer to Owner’s Manual.
OPERATION PROCEDURE
1. A: Turn the ignition switch ON. B: Turn the ignition switch from OFF to ACC after closing the driver door.
2. Front seat LH and steering wheel will return from the exiting position to entry position.
OPERATION CONDITION
Satisfy all of the following items. The entry assist function is not performed if t hese items are not satisfied.
DETAIL FLOW
ALJIA0238GB
ItemRequest status
Seat, steering wheel The vehicle is not moved after performing the
exit assist function.
Switch inputs
• Power seat switch
• Pedal adjusting switch
• ADP steering switch
• Door mirror control switch
• Set switch
• Memory switch OFF
(Not operated)
A/T selector lever P position
Revision: April 20092010 QX56

ADP-26
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
ENTRY ASSIST FUNCTION : Component Parts Location
INFOID:0000000005370292
Order Input Output Control unit condition
1 Door switch/Ignition
switch —
Driver seat control unit receives the signals of ignition switch signal
and front door switch from BCM via CAN communication.
2 —
Motors (sliding, tilt) Driver seat control unit operates the sliding motor when the operating
conditions are satisfied. Driver seat control unit then requests the op-
eration of the tilt motor to the automatic drive positioner control unit
via UART communication. The automatic drive positioner control unit
operates the motor for a constant amount.
Sensors (sliding, tilt) —Sensors monitor the operating positions of seat and steering wheel
and then stops the operation of each motor when each part reaches
the recorded address.
ALJIA0347ZZ
1. A. Automatic drive positioner control
unit M33, M34
B. Pedal adjusting motor assembly
E109, E110 2. A. Steering column
B. Key switch and ignition knob
switch M12
C. BCM M18, M19, M20 (view with
instrument panel removed) 3. A. Door mirror remo
te control switch
D10
B. Seat memory switch D5
4. Pedal adjusting switch M96 5 . A. Door mirrror LH D4, RH D107
B. Front door switch LH B 6. A. A/T selector lever
B. A/T shift selector (park position
switch) M203
7. A. Sliding motor LH B204 (driver seat
view), reclining motor LH B205, lift-
ing motor (front) B206, lifting motor
(rear) B207
B. Driver seat control unit B202,
B203
C. Power seat switch LH B208 8. A. ADP steering switch M16
B. Tilt sensor M85 and tilt motor M86
Revision: April 20092010 QX56

ADP-28
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (DRIVER SEAT C/U)
DIAGNOSIS SYSTEM (DRIVER SEAT C/U)
Diagnosis DescriptionINFOID:0000000005147445
The auto drive positioner system can be checked and diagnosed for component operation with CONSULT-III.
DIAGNOSTIC MODE
CONSULT-III FunctionINFOID:0000000005147446
SELF-DIAGNOSIS RESULTS
Refer to ADP-134, "DTCIndex".
DATA MONITOR
Diagnostic mode
[AUTO DRIVE POS.] Description
WORK SUPPORT Changes the setting of each function.
SELF-DIAG RESULTS Performs self-diagnosis for the auto drive positioner system and displays the results.
DATA MONITOR Displays input signals transmitted from various switches and sensors to driver seat con-
trol unit in real time.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
ACTIVE TEST Drive each output device.
ECU PART NUMBER Displays part numbers of driver seat control unit parts.
Monitor ItemUnitMain
Signals Selection
From
Menu Contents
SET SW “ON/OFF”×× ON/OFF status judged from the setting switch signal.
MEMORY SW1 “ON/OFF”×× ON/OFF status judged from the seat memory switch 1 sig-
nal.
MEMORY SW2 “ON/OFF”×× ON/OFF status judged from the seat memory switch 2 sig-
nal.
SLIDE SW–FR “ON/OFF”×× ON/OFF status judged from the sliding switch (forward) sig-
nal.
SLIDE SW–RR “ON/OFF”×× ON/OFF status judged from the sliding switch (backward)
signal.
RECLN SW–FR “ON/OFF”×× ON/OFF status judged from the reclining switch (forward)
signal.
RECLN SW–RR “ON/OFF”×× ON/OFF status judged from the reclining switch (backward)
signal.
LIFT FR SW–UP “ON/OFF” ××ON/OFF status judged from the lifting switch front (up) sig-
nal.
LIFT FR SW–DN “ON/OFF” ××ON/OFF status judged from the lifting switch front (down)
signal.
LIFT RR SW–UP “ON/OFF” ××ON/OFF status judged from the lifting switch rear (up) sig-
nal.
LIFT RR SW–DN “ON/OFF” ××ON/OFF status judged from the lifting switch rear (down)
signal.
MIR CON SW–UP “ON/OFF” ××ON/OFF status judged from the mirror switch (up) signal.
MIR CON SW–DN “ON/OFF” ××ON/OFF status judged from the mirror switch (down) signal.
MIR CON SW–RH “ON/OFF” ××ON/OFF status judged from the door mirror remote control
switch (passenger side) signal.
MIR CON SW–LH “ON/OFF” ××ON/OFF status judged from the door mirror remote control
switch (driver
side) signal.
Revision: April 20092010 QX56

DIAGNOSIS SYSTEM (DRIVER SEAT C/U)ADP-29
< FUNCTION DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
ACTIVE TEST
CAUTION:
When driving vehicle, do not perform active test.
MIR CHNG SW–R “ON/OFF” ××ON/OFF status judged from the door mirror remote control
switch (switching to right) signal.
MIR CHNG SW–L “ON/OFF” ××ON/OFF status judged from the door mirror remote control
switch (switching to left) signal.
TILT SW-UP “ON/OFF”×× ON/OFF status judged from the ADP steering switch (UP)
signal.
TILT SW-DOWN “ON/OFF”×× ON/OFF status judged from the ADP steering switch
(DOWN) signal.
PEDAL SW-FR “ON/OFF”×× ON/OFF status judged from the pedal adjusting switch (for-
ward) signal.
PEDAL SW-RR “ON/OFF”×× ON/OFF status judged from the pedal adjusting switch
(backward) signal.
DETENT SW “ON/OFF”×× The selector lever position “OFF (P position) / ON (other
than P position)” judged from the detention switch signal.
STARTER SW “ON/OFF”×× Ignition key switch ON (START, ON) /OFF (ACC, OFF) sta-
tus judged from the ignition switch signal.
SLIDE PULSE —–×Value (32768) when battery connections are standard. If it
moves backward, the value increases. If it moves forward,
the value decreases.
RECLN PULSE —–×Value (32768) when battery connections are standard. If it
moves backward, the value increases. If it moves forward,
the value decreases.
LIFT FR PULSE —–×Value (32768) when battery connections are standard. If it
moves DOWN, the value increases. If it moves UP, the val-
ue decreases.
LIFT RR PULSE —–×Value (32768) when battery connections are standard. If it
moves DOWN, the value increases. If it moves UP, the val-
ue decreases.
MIR/SEN RH U–D “V”–×Voltage input from door mirror sensor (passenger side) up/
down is displayed.
MIR/SEN RH R–L “V”–×Voltage input from door mirror sensor (passenger side) left/
right is displayed.
MIR/SENLHU–D “V”–×Voltage input from door mirror
sensor (driver side) up/down
is displayed.
MIR/SENLHR–L “V”–×Voltage input from door mirror sensor (driver side) left/right
is displayed.
PEDAL SEN “V”–×Pedal position (voltage) judged from the pedal adjusting
sensor signal is displayed.
Monitor Item
UnitMain
Signals Selection
From
Menu Contents
Test item
Description
SEAT SLIDE Activates/deactivates the sliding motor.
SEAT RECLINING Activates/deactivates the reclining motor.
SEAT LIFTER FR Activates/deactivates the lifting motor (front).
SEAT LIFTER RR Activates/deactivates the lifting motor (rear).
ADJ PEDAL MOTOR Activates/deactivates the pedal adjusting motor.
TILT MOTOR Activates/deactivates the tilt motor.
MIRROR MOTOR RH Activates/deactivates the mirror motor (passenger side).
Revision: April 20092010 QX56

ADP-30
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (DRIVER SEAT C/U)
WORK SUPPORT
MIRROR MOTOR LHActivates/deactivates the mirror motor (driver side).
MEMORY SW INDCTR Turns ON/OFF the memory indicator.
Test item
Description
Work itemContentItem
SEAT SLIDE VOLUME SET The amount of seat sliding for entry/exit assist can be selected
from 3 items. 40 mm
80 mm
150 mm
EXIT SEAT SLIDE SETTING Entry/exit assist (seat) can be selected:
ON (operated) – OFF (not operated) ON
OFF
EXIT TILT SETTING Entry/exit assist (tilt) can be selected:
ON (operated) – OFF (not operated) ON
OFF
Revision: April 20092010 QX56

B2118 TILT SENSORADP-39
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
1. Turn ignition switch OFF.
2. Check voltage between automatic drive positioner connector
and ground.
Is the inspection result normal?
YES >> Tilt sensor circuit is OK.
NO >> GO TO 3
3. CHECK HARNESS CONTINUITY
1. Disconnect automatic drive positioner control unit and tilt motor assembly.
2. Check continuity between automatic drive positioner connector M33 (A), M34 (B) terminals 7, 33, 41 and tilt motor assembly
connector M85 (C) terminals 2, 3, 4.
3. Check continuity between automat ic drive positioner control unit
connectors M33 (A), M34 (B ) terminals 7, 33, 41 and ground.
Is the inspection result normal?
YES >> Replace tilt motor assembly. Refer to ST-19, "Removal
and Installation".
NO >> Repair or replace harness.
4. CHECK DOOR MIRROR OPERATION
1. Connect automatic drive positioner c ontrol unit and tilt motor assembly.
2. Turn ignition switch ON.
3. Check door mirror operation with memory function.
Is the operation normal?
YES >> Replace tilt motor assembly. Refer to ST-19, "Removal and Installation".
NO >> GO TO 5
5. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace automatic drive posit ioner control unit. Refer to ADP-175, "Removal and Installation".
NO >> Repair or replace the malfunctioning part.
Connector Te r m i n a l s
ConditionVoltage (V)
(Approx.)
(+) (-)
M33 7 Ground Tilt top position 2
Tilt bottom position
4
LIIA0485E
7 - 3: Continuity should exist.
33 - 2 : Continuity should exist.
41 - 4 : Continuity should exist.
7 - Ground : Continuity should not exist.
33 - Ground : Continuity should not exist.
41 - Ground : Continuity should not exist.
ALJIA0291ZZ
Revision: April 20092010 QX56

ADP-44
< COMPONENT DIAGNOSIS >
B2128 UART COMMUNICATION LINE
B2128 UART COMMUNICATION LINE
DescriptionINFOID:0000000005147474
Driver seat control unit performs UART communication with the automatic drive positioner control unit using 2
communication lines, TX and RX line. Driver seat cont rol unit receives the operation signals of pedal adjusting
switch, door mirror remote control switch, set switch and memory switch and the position signals of adjustable
pedal sensor and door mirror sensor from the automatic drive positioner control unit and transmits the opera-
tion request signal.
DTC LogicINFOID:0000000005147475
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. STEP 1
Turn ignition switch ON.
>> GO TO 2
2. STEP 2
Operate pedal adjusting switch for more than 2 seconds.
>> GO TO 3
3. PROCEDURE 3
Check “Self diagnostic result” with CONSULT-III.
Is the DTC detected?
YES >> Perform diagnosis procedure. Refer to ADP-44, "DiagnosisProcedure".
NO >> Inspection End.
Diagnosis ProcedureINFOID:0000000005147476
Regarding Wiring Diagram information, refer to ADP-119, "Wiring Diagram".
1. CHECK UART COMMUNICATION LINE CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect driver seat contro l unit and automatic drive posi-
tioner control unit.
3. Check continuity between driver seat control unit harness con- nector and automatic drive positioner control unit harness con-
nector.
DTC No. Trouble diagnosis name DTC detecting conditionPossible cause
B2128 UART COMM The communication between driver seat control unit
and automatic drive positioner control unit is interrupt-
ed for a period of time. • UART communication line
(UART communication line is
open or shorted)
• Driver seat control unit
• Automatic drive positioner control unit
Driver seat control unit connector Te r m i n a lAutomatic drive positioner
control unit connector Terminal Continuity
PIIA4598E
Revision: April 20092010 QX56