2010 INFINITI M display

Voice recognition settings
The available settings of the INFINITI Voice
Recognition system are described.
1. Highlight ªVoice Recognition Settingsºand push the ENTERbutton.
2. You can confirm the page by scrolling the screen using the INFINITI controller.
USING THE SYSTEM
Initialization
When the ignition switch is pushed to the ON
position, INFINITI Voice Recognition is initial-
ized, which takes a few seconds. When com-
pleted, the system is ready to accept voice
commands. If the TALK
switch is pushed before the initialization completes, the display
will show the message: ªPhonetic data down-
loaded. Please wait.º or a beep sounds.
Before starting
To get the best recognition performance from
INFINITI Voice Recognition, observe the follow-
ing:
c
The interior of the vehicle should be as quiet
as possible. Close the windows to eliminate
the surrounding noises (traffic noise and
vibration sounds, etc.), which may prevent
the system from correctly recognizing the
voice commands.
c Wait until the tone sounds before speaking a
command.
c Speak in a natural conversational voice with-
out pausing between words.
c If the air conditioner is set to ªAutoº, the fan
speed is automatically lowered so that your
commands can be recognized more easily.
Giving voice commands
1. Push the TALKswitch located on the
steering wheel.
SAA2166SAA1113
Monitor, climate, audio, phone and voice recognition systems4-101
wÐ
Ð
05/14/09Ðpattie
X

2. A list of commands appears on thescreen, and the system announces,
ªWould you like to access Phone, Naviga-
tion, Information or Help?º.
3. After the tone sounds and the icon on the screen changes from
to,
speak a command.
4. Continue to follow the voice menu prompts and speak after the tone sounds
until your desired operation is completed.
Operating tips :
cSay a command after the tone.
c Commands that are available are always
shown on the display and spoken through
voice menu prompts. Commands other than those that are displayed are not accepted.
Please follow the prompts given by the
system.
c If the command is not recognized, the sys-
tem announces, ªPlease say againº. Repeat
the command in a clear voice.
c Push the BACKbutton once to return to the
previous screen.
c If you want to cancel the command, push
and hold the TALK
switch. The mes-
sage, ªVoice cancelledº will be announced.
c Push the TALK
switch to pause the
operation. Push the TALK
switch
again to restart the operation.
c If you want to adjust the volume of the
system feedback, push the volume control
buttons [+] or [2] on the steering switch or
use the audio system volume knob while the
system is making an announcement.
How to speak numbers :
INFINITI Voice Recognition requires a certain
way to speak numbers when giving voice com-
mands. Refer to the following examples. General rule
Only single digits 0 (zero) to 9 can be used. (For
example, if you would like to say 500, ªfive zero
zeroº can be used, but ªfive hundredº cannot.)
Examples
c
1-800-662-6200
± ªOne eight zero zero six six two six two zero zeroº
Improving Recognition of Phone numbers
You can improve the recognition of phone num-
bers by saying the phone number in three
groups of numbers. For example, when you try
to call 800-662-6200, say ªeight zero zeroº
first, and the system will then ask you for the
next three digits. Then, say ªsix six twoº. After
recognition, the system will then ask for the last
four digits. Say, ªsix two zero zeroº. Using this
method of phone digit entry can improve recog-
nition performance.
When speaking a house number, speak the
number ª0º as ªzeroº. If the letter ªo (Oh)º is
included in the house number, it will not be
recognized as the number ª0 (zero)º even if you
speak ªohº instead of ªzeroº. You can only say
ªzeroº for ª0 (zero)º. You can say either ªzeroº
or ª ohº for ªo (Oh)º.
SAA1908
4-102Monitor, climate, audio, phone and voice recognition systems
wÐ
Ð
05/14/09Ðpattie
X

Command List
Category Command:
CommandAction
Phone Operates Phone function
Navigation Operates Navigation function
Information Displays vehicle Information function
Help Displays User Guide
c Phone Command:
Command Action
Dial Number Makes a call to a spoken phone number up to 10 digits.
Redial Makes a call to the latest dialed number.
Phonebook Makes a call to a contact that is stored in the Phonebook.
International Call Makes an international call by allowing more than 10 digits to be spoken.
Change Number Corrects the phone number when it is not recognized. (Available during phone number entry)
c Navigation Command:
See the separate Navigation System Owner's Manual.
Monitor, climate, audio, phone and voice recognition systems4-103
wÐ
Ð
05/14/09Ðpattie
X

cInformation Command:
Command Action
Fuel Economy Displays fuel economy information.
Trip Computer Displays trip information.
Maintenance Displays maintenance information.
Traffic Info. Turns the traffic information system ON and OFF.
4-104Monitor, climate, audio, phone and voice recognition systems
wÐ
Ð
05/14/09Ðpattie
X

5. Speak ª011811112223333º.6. Speak ªDialº.
7. System makes a call to 011-81-111-222- 3333.
Note :
Any digit input format is available in the Inter-
national Number input process.
INFINITI VOICE RECOGNITION
ALTERNATE COMMAND MODE
The following section is applicable when Alter-
nate Command Mode is activated. (This mode is
selected by default for Canadian customers.)
The Alternate Command Mode enables the op-
eration of the display, audio, and climate con-
trol through Voice Recognition. When this mode
is active, an expanded list of commands can be
spoken after pushing the TALK
switch,
and the voice command menu prompts are
turned off.
Please note that in this mode the recognition
success rate may be affected as the number of
available commands and ways of speaking each
command are increased. To improve the recog-
nition success rate, try using the Speaker Ad-
aptation Function available in that mode. (See
ªSpeaker adaptation functionº later in this sec-
tion.)
In the Alternate Command Mode, review the
expanded command list for this mode, as some
commands available in the Standard Mode are
replaced. Please see the examples on the
screen.
SAA1914SAA1915
Monitor, climate, audio, phone and voice recognition systems4-109
wÐ
Ð
05/14/09Ðpattie
X

Activating Alternate Command Mode
When the Standard Mode is active, perform the
following steps to switch to the Alternate Com-
mand Mode.
1. Push theSETTINGbutton on the instru-
ment panel.
2. Highlight the ªOthersº key on the display and then push the ENTERbutton.
3. Highlight the ªVoice Recognitionº key and then push the ENTERbutton. 4. Highlight the ªAlternate Command Modeº
key and push the ENTERbutton.
5. The confirmation message is displayed on the screen. Push the ªOKº key to activate
the Alternate Command Mode.Displaying command list
If you are controlling the system by voice
commands for the first time or do not know the
appropriate voice command, perform the fol-
lowing procedure for displaying the voice com-
mand list (available only in Alternate Command
Mode).
1. Push the INFObutton on the instrument
panel.
2. Highlight the ªOthersº key using the INFINITI controller and push the ENTER
button.
3. Highlight the ªVoice Recognitionº key us- ing the INFINITI controller and push the
ENTER button.
You can skip steps 1 to 3 above if you say
ªHelpº.
4. Highlight the ªCommand Listº key using
the INFINITI controller and push the ENTER
button.
SAA1916SAA2168SAA1803
4-110Monitor, climate, audio, phone and voice recognition systems
wÐ
Ð
05/14/09Ðpattie
X

cSatellite
COMMAND ACTION
Satellite Radio Turns the SAT radio on, selecting the station and band last played.
cCD
COMMAND ACTION
CD Starts to play a CD.
cAudio
COMMAND ACTION
Audio OFF Turns the audio system off.
ciPodT
COMMAND ACTION
iPodT Turns the iPodTsystem on.
Vehicle Information Commands:
COMMAND ACTION
Traffic Info. Turns the traffic information system ON and OFF.
Fuel Economy Displays the Fuel Economy screen.
Trip Computer Displays the Trip Computer screen.
Maintenance Displays the Maintenance screen.
Tire Pressure Displays the Tire Pressure screen.
Monitor, climate, audio, phone and voice recognition systems4-113
wÐ
Ð
05/15/09Ðpattie
X

Displaying user guide
You can confirm how to use voice commands by
accessing a simplified User Guide, which con-
tains basic instructions and tutorials for several
voice commands.
1. Push theINFObutton on the instrument
panel.
2. Highlight the ªOthersº key using the INFINITI controller and push the ENTER
button. 3. Highlight the ªVoice Recognitionº key us-
ing the INFINITI controller and push the
ENTER button.
You can skip steps 1 to 3 above if you say
ªHelpº.
4. Highlight the ªUser Guideº key using the
INFINITI controller and push the ENTER
button.
5. Highlight an item using the INFINITI con-troller and push the ENTERbutton.
Available items :
cGetting Started
Describe the basics of how to operate the
INFINITI Voice Recognition system.
c Using the Address Book
Refer to Navigation System Owner's Manual.
c Finding a Street Address (if so equipped)
Refer to Navigation System Owner's Manual.
c Placing Calls
Tutorial for making a phone call by voice
command operation.
SAA1783SAA2170
Monitor, climate, audio, phone and voice recognition systems4-115
wÐ
Ð
05/15/09Ðpattie
X