2010 FORD MONDEO sensor

Downloaded from www.Manualslib.com manuals search engine Locking and unlocking the
doors with the key blade
1. Carefully remove the cover.
2.
Remove the key blade and insert it into
the lock.
AUTOWIPERS WARNING
For all warnings and cautions, refer
to your Owner's handbook.
Low sensitivity
A
OnB
High sensitivity
C
The rain sensor will continuously measure
the amount of water on the windscreen
and adjust the speed of the front wipers
automatically. Adjust the sensitivity of the rain sensor
using the rotary control.
CHANGING THE WIPER
BLADES
WARNING
For all warnings and cautions, refer
to your Owner's handbook.
Windscreen wiper blades
CAUTION
Set the windscreen wipers in the
service position to change the wiper
blades.
Service position
4121E87964 E71013CAB E85833 AE75188

Downloaded from www.Manualslib.com manuals search engine Switch off the ignition and move the wiper
lever to positionAwithin three seconds.
Release the lever when the windscreen
wipers have moved to the service position.
AUTOMATIC MAIN BEAM
CONTROL
WARNINGS
For all warnings and cautions, refer
to your Owner's handbook.
The system does not relieve you of
your responsibility to drive with due
care and attention. A manual
override may be necessary if the system
fails to switch the main beam on or off.
CAUTION
In cold and severe weather conditions
the system may not function. A
manual override may be necessary in
these cases.
The system will automatically switch on
main beam if it is dark enough and no
other traffic is present. If it detects an
approaching vehicle’s headlamps or tail
lamps, or street lighting ahead the system
will switch off main beam before it can
distract other road users.
Once the system is active the main beam
will switch on if:
• it is dark enough to require the use of
main beams and
• there is no traffic or street lighting
ahead and
• vehicle speed is greater than 40 km/h
(25 mph).
The main beam will switch off if:
• The ambient light is high enough that
main beam is not required.
• An approaching vehicle's headlamps
or tail lamps are detected.
• Street lighting is detected. •
Vehicle speed falls below 25 km/h (16
mph).
• The camera sensor is too hot or
becomes blocked.
Activating the system
Switch on the system using the information
display and autolamps.
E70719
Turn the switch to the autolamps position.
Manually overriding the system
E70725
Use the main beam lever to switch
between main beam and dipped beam.
ELECTRIC WINDOWS
WARNING
For all warnings and cautions, refer
to your Owner's handbook.
5

Downloaded from www.Manualslib.com manuals search engine Using the system
The system displays a yellow indicator
located in the exterior mirrors.
Detection limitations
There may be certain instances where
vehicles entering and exiting the blind spot
zones may not be detected.
Instances which may cause non-detection:
•
Debris build up on the rear bumper
panels in the area of the sensors.
• Certain manoeuvring of vehicles
entering and exiting the blind zone.
• Vehicles passing through the blind
zone at high speed.
• Severe weather conditions.
• Several vehicles passing through the
blind zone following each other closely. Turning the system on and off
You can turn the system on and off using
the information display.
MANUAL CLIMATE CONTROL
Cooling the interior quickly
Heating the interior quickly
Recommended settings for
cooling
Open the centre and side air vents.
Direct the centre air vents upwards and
the side air vents toward the side windows.
Recommended settings for
heating
7AAE124788 E124736 E71381 E71377 E131534 E131535

Downloaded from www.Manualslib.com manuals search engine Insert the fuel nozzle up to and including
the first notch on the nozzle. Keep it
resting on the cover of the fuel pipe
opening.
WARNING
We recommend that you wait at
least 10 seconds before removing
the fuel nozzle to allow any residual
fuel to drain into the fuel tank. Slightly raise the fuel nozzle to remove it.
USING THE PARKING AID
WARNING
For all warnings and cautions, refer
to your Owner's handbook.
Switching the parking aid on
and off
Note:The parking aid switches off
automatically when you start the engine or when you exceed 16 km/h (10 mph).
Note:The front and rear sensors are
always activated or deactivated together.
The parking aid is per default off. To switch
the parking aid on, press the switch in the
instrument panel or select reverse gear.
The light in the switch illuminates when the
parking aid is activated.
To turn it off, press the switch again.
DRIVER ALERT WARNINGS
For all warnings and cautions, refer
to your Owner's handbook.
The system does not relieve you of
your responsibility to drive with due
care and attention.
Take regular rest breaks as required
and do not wait for the system to
warn you if you feel tired.
CAUTIONS
In cold and severe weather conditions
the system may not function. Rain,
snow, spray and large contrasts in
lighting can all influence the sensor. The system may not operate on roads
with sharp bends or narrow lanes.
The system automatically monitors your
driving behaviour using various inputs
including the front camera sensor.
If the system detects that you are
becoming drowsy or there is a
deterioration in your driving, the system
will alert you.
USING DRIVER ALERT
Switching the system on and off
Activate the system using the information
display.
12E119080 E119081

Downloaded from www.Manualslib.com manuals search engine System display
When active the system will run
automatically in the background and only
issue warnings if required. You can view
the status at any time using the information
display.
The alertness level is shown by six steps
as a coloured bar.
The status bar will travel from left to right
as the calculated alertness level
decreases.
•
Green - No rest required.
• Yellow - First (temporary) warning.
• Red - Second warning.
LANE DEPARTURE WARNING WARNINGS
For all warnings and cautions, refer
to your Owner's handbook.
The system does not relieve you of
your responsibility to drive with due
care and attention.
CAUTIONS
In cold and severe weather conditions
the system may not function. Rain,
snow, spray and large contrasts in
lighting can all adversely influence the
camera sensor. The system may not operate on roads
with sharp bends or narrow lanes. The system will automatically detect and
track the lane markings on the road. If it
detects that the vehicle is unintentionally
drifting towards the lane boundaries then
a visual warning will be displayed in the
information display. There is also a warning
given in the form of a vibration felt through
the steering wheel.
USING LANE DEPARTURE
WARNING
Switching the system on and off
Lane departure warning on
A
Lane departure warning off
B
System warnings Once active the system will show detected
lane markings as two columns of solid
dots.
13E131358 E131360AB E131363

Downloaded from www.Manualslib.com manuals search engine •
Green - The system is ready to warn
you if an unintentional lane departure
may occur.
• Red - The vehicle is approaching or is
too close to the detected lane
boundary.
• Grey - Right or left-hand lane boundary
is suppressed.
Instances where a lane boundary may be
suppressed:
• Lane markings on the road may not be
detected by the camera sensor.
• The direction indicator for that side of
the vehicle is on.
• During hard acceleration and braking,
or if direct steering is applied.
• If ABS or Stability Control (ESP) is
active.
• Narrow lane width.
If the dots turn red or a vibration is felt
through the steering wheel you must take
immediate and safe action to align the
vehicle and correct any unintended lane
drift.
BLUETOOTH SETUP
The Bluetooth mobile phone part of the
system provides interaction with the audio
system and your mobile phone. It allows
you to use the audio system to make and
receive calls without having to hold your
mobile phone.
During bonding, if your mobile phone asks
you to authorize the automatic connection,
select YES.
Refer to your Owner's handbook and also
www.ford-mobile-connectivity.com for
details.
14