2010 DODGE JOURNEY lock

CavityCartridge
Fuse Mini-
Fuse Description
M20
—15 Amp
Blue
Electronic Vehicle In-
formation Center
(EVIC) – If Equipped,
Interior Lighting,
Steering Wheel
Switches – If
Equipped, Switch
Bank
M21 —20 Amp
Yellow Auto Shut Down
(ASD) #3
M22 —10 Amp
Red Right Horn
M23 —10 Amp
Red Left Horn
M24 —25 Amp
Natural Rear WiperCavity
Cartridge
Fuse Mini-
Fuse Description
M25 —20 Amp
Yellow Fuel Pump/Diesel
Lift Pump
M26 —10 Amp
Red Power MIRRORS
Switch/Drivers Win-
dow Switch
M27
—10 Amp
Red
Steering Column
Lock, Wireless Igni-
tion Node (WIN)/
PEM
M28
—10 Amp
Red
NGC (Powertrain
Control Module)/
Transmission Feed
(Batt)
M29 —10 Amp
Red Occupant Classifica-
tion Module (OCM)
446 MAINTAINING YOUR VEHICLE

CavityCartridge
Fuse Mini-
Fuse Description
M30 —15 Amp
Blue
Rear Wiper Module
Module/Power Fold-
ing Mirror, J1962 Diag
Feed
M31 —20 Amp
Yellow Back-Up Lights
M32 —10 Amp
Red Occupant Restraint
Controller (ORC)
M33 —10 Amp
Red NGC (Powertrain
Control Module) Bat-
tery Feed/TCMCavity
Cartridge
Fuse Mini-
Fuse Description
M34
—10 Amp
Red
Power Assist Module,
HVAC Module, Head-
lamp Washers, Com-
pass Module – If
Equipped, Flashlight
– If Equipped, RAD
Fan Diesel
M35 —10 Amp
Red Heated Mirrors – If
Equipped
M36 —20 Amp
Yellow Power Outlet #3
(Batt)
M37
—10 Amp
Red
Anti-Lock Brake Sys-
tem (ABS), Electronic
Stability Program
(ESP), Stop Light
Switch
7
MAINTAINING YOUR VEHICLE 447

CavityCartridge
Fuse Mini-
Fuse Description
M38 —25 Amp
Natural Lock/Unlock Motors
K1
—— Ignition Run/
Accessory Relay
K2 — — Ignition Run Relay
K3 — — Starter Solenoid Relay
K4 —— Ignition Run/Start
Relay
K5 —— (NGC) Powertrain
Control Module
Relay/PCM
K6 —— Electric Back Light
(EBL) Relay
K7 — — —
K8 — — —
K9 — — Rear Blower Relay
K10 —— ASD Relay (Feed for
M19 and M21)
K11 —— Radiator Fan Relay
Low Speed
VEHICLE STORAGE
If you will not be using your vehicle for more than
21 days you may want to take steps to preserve your
battery. You may:
•Remove the IOD (Ignition Off-Draw) mini-fuses from
the Totally Integrated Power Module located in the
engine compartment.
•Or, disconnect the battery negative cable.
448 MAINTAINING YOUR VEHICLE

BULB REPLACEMENT
Low Beam Headlamp, High Beam Headlamp,
Front Turn Signal/Park Lamp, Side Marker Lamp
1. Open the hood.
NOTE:It may be necessary to remove the air cleaner
filter housing and position the Totally Integrated Power
Module (TIPM) aside to replace certain lamps in the left
headlamp housing.
2. Rotate the applicable bulb and connector assembly
14
turn counterclockwise and remove the assembly from the
headlamp housing.
3. Disconnect the bulb from the harness connector and
then connect the replacement bulb.
1 — Front Turn Signal/Park Lamp Bulb
2 — Side Marker Lamp Bulb
3 — Low Beam Headlamp Bulb
4 — High Beam Headlamp Bulb
450 MAINTAINING YOUR VEHICLE

CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
4. Install the bulb and connector assembly into the
headlamp housing and rotate it
14turn clockwise to lock
it in place.
Front Fog Lamp
NOTE: Turn the steering wheel to the right if replacing
the left front fog lamp or to the left if replacing the right
front fog lamp to allow for easier access to the front of the
wheel well.
1. Remove the fasteners retaining the front lower wheel
well access panel and remove the access panel. 2. Remove the electrical connector from the fog lamp
housing.
3. Remove the bulb from the connector socket and install
the replacement bulb.
7
MAINTAINING YOUR VEHICLE 451

CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with an oily surface, clean the
bulb with rubbing alcohol.
4. Install the bulb and connector assembly into the fog
lamp housing and rotate the connector
14turn clockwise
to lock it in place.
5. Reinstall the front lower wheel well access panel and
fasteners.
Tail/Stop Lamp, Rear Turn Signal Lamp, Tail
Lamp, Backup Lamp
The taillamps are a two-piece design. The tail/stop/rear
turn signal lamps are located in the rear corner body
panels. The tail and backup lamps are located in the
liftgate.
Changing the Tail/Stop/Rear Turn Signal Lamp
1. Open the liftgate.
2. Remove the two fasteners from the inboard side of the
taillamp housing.
3. Carefully insert a trim stick (plastic flat-blade tool)
between the body panel and the outboard side of the
taillamp housing with one hand and grasp the flange on
the inboard side of the taillamp housing with the other
hand. Use the trim stick and hand pressure together to
disengage the taillamp housing from the vehicle.
4. Rotate the applicable bulb’s electrical connector
14
turn counterclockwise and remove it from the taillamp
housing.
5. Remove the bulb from the connector socket and install
the replacement bulb.
452 MAINTAINING YOUR VEHICLE

6. Install the bulb and connector assembly into the
taillamp housing and rotate the connector14turn clock-
wise to lock it in place.
7. Reinstall the taillamp housing and fasteners.
Changing the Tail Lamp or Backup Lamp
1. Open the liftgate.
2. Remove the two fasteners retaining the taillamp hous-
ing to the liftgate from the inboard face of the liftgate.
3. Carefully insert a trim stick (plastic flat-blade tool)
between the taillamp housing and the liftgate. Use the
trim stick and hand pressure together to disengage the
taillamp housing from the liftgate.
4. Rotate the applicable bulb’s electrical connector
14
turn counterclockwise and remove it from the housing. 5. Remove the bulb from the connector socket and install
the replacement bulb.
6. Install the bulb and connector assembly into the
housing and rotate the connector
14turn clockwise to
lock it in place.
1 — Tail Lamp Bulb
2 — Backup Lamp Bulb
7
MAINTAINING YOUR VEHICLE 453

7. Reinstall the taillamp housing and fasteners.
License Plate Lamp
1. Push the small locking tab sticking out of the end of
the lens toward the side of the vehicle and hold it in that
position.2. Insert a small flat-blade tool between the end of the
lens with the locking tab and the surrounding housing
and then pivot the tool to separate the lens from the
housing.
3. Hold the lens with one hand and rotate the bulb’s
electrical connector
14turn counterclockwise with the
other hand and then separate the bulb and connector
assembly from the lens.
4. Remove the bulb from the connector socket and install
the replacement bulb.
5. Install the bulb and connector assembly into the lens
and rotate the connector
14turn clockwise to lock it in
place.
6. Insert the end of the lens without the locking tab into
the housing on the liftgate and then push the opposite
end of the lens into the housing, making sure it locks in
the housing.
License Lamp
454 MAINTAINING YOUR VEHICLE