2010 CADILLAC ESCALADE automatic transmission

Automatic Transmission Fluid
When to Check and Change Automatic
Transmission Fluid
It is usually not necessary to check the transmissionfluid level. The only reason for fluid loss is atransmission leak or overheating the transmission.If you suspect a small leak, then use the followingchecking procedures to check the fluid level. However,if there is a large leak, then it may be necessary to havethe vehicle towed to a dealer/retailer service departmentand have it repaired before driving the vehicle further.
Notice:Use of the incorrect automatic transmissionfluid may damage the vehicle, and the damages maynot be covered by the vehicle's warranty. Alwaysuse the automatic transmission fluid listed inRecommended Fluids and Lubricants on page 8!10.
Change the fluid and filter at the intervals listed in theMaintenance Schedule. SeeScheduled Maintenanceo n p a g e 8!3. Be sure to use the transmission fluidlisted inRecommended Fluids and Lubricantsonpage 8!10.
How to Check Automatic Transmission
Fluid
Notice:Too much or too little fluid can damage yourtransmission. Too much can mean that some of thefluid could come out and fall on hot engine parts orexhaust system parts, starting a fire. Too little fluidcould cause the transmission to overheat. Be sureto get an accurate reading if you check yourtransmission fluid.
Before checking the fluid level, prepare the vehicle asfollows:
1. Start the engine and park the vehicle on a levelsurface. Keep the engine running.
2. Apply the parking brake and place the shiftlever in P (Park).
3. With your foot on the brake pedal, move the shiftlever through each gear range, pausing for aboutthree seconds in each range. Then, move the shiftlever back to P (Park).
7-24

Notice:Ignoring these steps could result in costlydamage to the vehicle that would not be covered bythe warranty.
Trying to start the vehicle by pushing or pulling itwill not work, and it could damage the vehicle.
1. Check the other vehicle. It must have a 12-voltbattery with a negative ground system.
Notice:If the other vehicle's system is not a 12-voltsystem with a negative ground, both vehicles canbe damaged. Only use vehicles with 12-volt systemswith negative grounds to jump start your vehicle.
2. Get the vehicles close enough so the jumpercables can reach, but be sure the vehicles are nottouching each other. If they are, it could cause aground connection you do not want. You would notbe able to start your vehicle, and the badgrounding could damage the electrical systems.
To avoid the possibility of the vehicles rolling, setthe parking brake firmly on both vehicles involvedin the jump start procedure. Put the automatictransmission in P (Park) or a manual transmissionin Neutral before setting the parking brake. If youhave a four-wheel-drive vehicle, be sure thetransfer case is in a drive gear, not in Neutral.
Notice:If you leave the radio or other accessorieson during the jump starting procedure, they couldbe damaged. The repairs would not be covered bythe warranty. Always turn off the radio and otheraccessories when jump starting the vehicle.
3. Turn off the ignition on both vehicles. Unplugunnecessary accessories plugged into thecigarette lighter or the accessory power outlets.Turn off the radio and all the lamps that are notneeded. This avoids sparks and helps save bothbatteries. And it could save the radio!
4. Open the hood on the other vehicle and locate thepositive (+) and negative (!) terminal locations onthat vehicle.
Your vehicle has a remote positive (+) jump startingterminal and a remote negative (!) jump startingterminal. You should always use these remoteterminals instead of the terminals on the battery.
If the vehicle has a remote positive (+) terminal, itis located under a red plastic cover at the positivebattery post. To uncover the remote positive (+)terminal, open the red plastic cover.
7-45

Tire Terminology and Definitions
Air Pressure:The amount of air inside the tire
pressing outward on each square inch of the tire.
Air pressure is expressed in pounds per square
inch (psi) or kilopascal (kPa).
Accessory Weight:This means the combined
weight of optional accessories. Some examples of
optional accessories are, automatic transmission,
power steering, power brakes, power windows,
power seats, and air conditioning.
Aspect Ratio:The relationship of a tire's height
to its width.
Belt:A rubber coated layer of cords that is
located between the plies and the tread. Cords
may be made from steel or other reinforcing
materials.
Bead:The tire bead contains steel wires wrapped
by steel cords that hold the tire onto the rim.
Bias Ply Tire:A pneumatic tire in which the plies
are laid at alternate angles less than 90 degrees
to the centerline of the tread.
Cold Tire Pressure:The amount of air pressure
in a tire, measured in pounds per square inch (psi)
or kilopascals (kPa) before a tire has built up heat
from driving. SeeInflation - Tire Pressureon
page 7!65.
Curb Weight:The weight of a motor vehicle with
standard and optional equipment including the
maximum capacity of fuel, oil, and coolant, but
without passengers and cargo.
DOT Markings:A code molded into the sidewall
of a tire signifying that the tire is in compliance
with the U.S. Department of Transportation (DOT)
motor vehicle safety standards. The DOT code
includes the Tire Identification Number (TIN), an
alphanumeric designator which can also identify
the tire manufacturer, production plant, brand, and
date of production.
GVWR:Gross Vehicle Weight Rating. See
Loading the Vehicleon page 6!32.
GAWR FRT:Gross Axle Weight Rating for the
front axle. SeeLoading the Vehicleon page 6!32.
GAWR RR:Gross Axle Weight Rating for the rear
axle. SeeLoading the Vehicleon page 6!32.
7-62

FusesUsage
1Right Trailer Stop/Turn Lamp
2Electronic Stability SuspensionControl, Automatic Level ControlExhaust
3Left Trailer Stop/Turn Lamp
4Engine Controls
5Engine Control Module, ThrottleControl
6Trailer Brake Controller
7Front Washer
8Oxygen Sensors
9Antilock Brakes System 2
10Trailer Back-up Lamps
11Driver Side Low-Beam Headlamp
12Engine Control Module (Battery)
13Fuel Injectors, Ignition Coils(Right Side)
14Transmission Control Module(Battery)
15Vehicle Back-up Lamps
16Passenger Side Low-Beam Headlamp
7-112

ApplicationCapacities
EnglishMetric
Transmission Fluid (Pan Removal and Replacement)6.0 qt5.7 L
Transfer Case Fluid1.5 qt1.4 L
Wheel Nut Torque140 lb ft190Y
All capacities are approximate. When adding, be sure to fill to the approximate level, as recommended in this manual.Recheck fluid after filling.†Oil filter should be changed at every oil change.
Engine Specifications
EngineVIN CodeTransmissionSpark Plug Gap
6.2L V8FAutomatic0.040 in (1.02 mm)
7-116

Every Engine Oil Change
.Change engine oil and filter. SeeEngine Oilonpage 7!17.An Emission Control Service.
.Engine coolant level check. SeeEngine Coolanton page 7!29.
.Windshield washer fluid level check. SeeWindshield Washer Fluid on page 7!39.
.Tire inflation check. SeeInflation - Tire Pressureon page 7!65.
.Tire wear inspection. SeeTire Inspection andRotation on page 7!71.
.Rotate tires. SeeTire Inspection and Rotationonpage 7!71.
.Fluids visual leak check (or every 12 months,whichever occurs first). A leak in any system mustbe repaired and the fluid level checked.
.Engine air cleaner filter inspection. SeeEngine AirCleaner/Filter on page 7!22.
.Brake system inspection (or every 12 months,whichever occurs first).
.Lubricate the front suspension, steering linkage,and parking brake cable guides. Control arm balljoints are maintenance!free.
.Steering and suspension inspection. Visualinspection for damaged, loose, or missing parts orsigns of wear.
.Engine cooling system inspection. Visualinspection of hoses, pipes, fittings, and clamps andreplacement, if needed.
.Windshield wiper blade inspection for wear,cracking, or contamination and windshield andwiper blade cleaning, if contaminated. SeeWindshield, Backglass, and Wiper Bladesonpage 7!104. Worn or damaged wiper bladereplacement. SeeWindshield Wiper BladeReplacement on page 7!57.
.Body hinges and latches, key lock cylinders, rearcompartment hinges, outer tailgate handle pivotpoints, and folding seat hardware lubrication. SeeRecommended Fluids and Lubricantsonpage 8!10. More frequent lubrication may berequired when vehicle is exposed to a corrosiveenvironment. Applying silicone grease onweatherstrips with a clean cloth makes them lastlonger, seal better, and not stick or squeak.
.Restraint system component check. SeeCheckingthe Restraint Systems on page 2!91.
.Automatic transmission fluid level check andadding fluid, if needed. SeeAutomaticTransmission Fluid on page 7!24.
8-4

Additional Required Services
At Each Fuel Stop
.Engine oil level check. SeeEngine Oilonpage 7!17.
.Engine coolant level check. SeeEngine Coolanton page 7!29.
.Windshield washer fluid level check. SeeWindshield Washer Fluid on page 7!39.
Once a Month
.Tire inflation check. SeeInflation - Tire Pressureon page 7!65.
.Tire wear inspection. SeeTire Inspection andRotation on page 7!71.
Once a Year
.Starter switch check. SeeOwner Checks andServices on page 8!8.
.Parking brake and automatic transmission P (Park)mechanism check. SeeOwner Checks andServices on page 8!8.
.Automatic transmission shiftlock control systemcheck. SeeOwner Checks and Servicesonp a g e 8!8.
.Ignition transmission lock check. SeeOwnerChecks and Services on page 8!8.
.Engine cooling system and pressure cap pressurecheck. Radiator and air conditioning condenseroutside cleaning. SeeCooling Systemonpage 7!28.
.Exhaust system and nearby heat shieldsinspection for loose or damaged components.
.Accelerator pedal check for damage, high effort,or binding. Replace if needed.
.Hood and liftgate support gas strut inspection forsigns of wear, corrosion, cracks, loss of lubricant,or other damage. Check the hold open ability ofthe gas strut. If necessary, replace with genuineparts from your dealer/retailer.
8-5

First Engine Oil Change After Every
40 000 km/25,000 Miles
.Fuel system inspection for damage or leaks.
First Engine Oil Change After Every
80 000 km/50,000 Miles
.Engine air cleaner filter replacement. SeeEngineAir Cleaner/Filter on page 7!22.
.Automatic transmission fluid and filter change(severe service) for vehicles mainly driven in heavycity traffic in hot weather, in hilly or mountainousterrain, when frequently towing a trailer, or used fortaxi, police, or delivery service. SeeAutomaticTransmission Fluid on page 7!24.
.Four!wheel drive only: Transfer case fluid change(severe service) for vehicles mainly driven whenfrequently towing a trailer, or used for taxi, police,or delivery service. Check vent hose at transfercase for kinks and proper installation. Check to besure vent hose is unobstructed, clear, and free of
debris. During any maintenance, if a power washeris used to clean mud and dirt from the underbody,care should be taken to not directly spray thetransfer case output seals. High pressure watercan overcome the seals and contaminate thetransfer case fluid. Contaminated fluid willdecrease the life of the transfer case and shouldbe replaced.
.Evaporative control system inspection. Check allfuel and vapor lines and hoses for proper hook!up,routing, and condition. Check that the purge valve,if the vehicle has one, works properly. Replace asneeded.An Emission Control Service. The U.S.Environmental Protection Agency or the CaliforniaAir Resources Board has determined that thefailure to perform this maintenance item will notnullify the emission warranty or limit recall liabilityprior to the completion of the vehicle's useful life.We, however, urge that all recommendedmaintenance services be performed at theindicated intervals and the maintenance berecorded.
8-6