2010 CADILLAC ESCALADE lock

To open the fuel door, push the rearward center edge inand release and it will open.
To remove the fuel cap, turn it slowly counterclockwise.The fuel cap has a spring in it; if the cap is released toosoon, it will spring back to the right.
While refueling, hang the tethered fuel cap from thehook on the fuel door.
{WARNING:
Fuel can spray out on you if you open the fuel cap
too quickly. If you spill fuel and then something
ignites it, you could be badly burned. This spray
can happen if the tank is nearly full, and is more
likely in hot weather. Open the fuel cap slowly and
wait for any hiss noise to stop. Then unscrew the
cap all the way.
Be careful not to spill fuel. Do not top off or overfill thetank and wait a few seconds after you have finishedpumping before removing the nozzle. Clean fuel frompainted surfaces as soon as possible. SeeWashingYour Vehicle on page 7!102.
When replacing the fuel cap, insert the tether in its holebefore tightening the cap. Turn the fuel cap clockwiseuntil it clicks. It will require more effort to turn the fuelcap on the last turn as you tighten it. Make sure the capis fully installed. The diagnostic system can determine ifthe fuel cap has been left off or improperly installed.This would allow fuel to evaporate into the atmosphere.SeeMalfunction Indicator Lamp on page 4!36
7-12

A.Engine Air Cleaner/Filter on page 7!22.
B. Coolant Surge Tank and Pressure Cap.SeeCooling System on page 7!28.
C. Remote Positive (+) Terminal. SeeJump Startingon page 7!44.
D.Battery on page 7!43.
E. Engine Oil Fill Cap. See“When to Add Engine Oil”underEngine Oil on page 7!17.
F. Automatic Transmission Dipstick (Out of View).See“Checking the Fluid Level”underAutomaticTransmission Fluid on page 7!24.
G. Remote Negative (!) Terminal (GND) (Out ofView). SeeJump Starting on page 7!44.
H. Engine Oil Dipstick (Out of View). See“CheckingEngine Oil”underEngine Oil on page 7!17.
I. Engine Cooling Fan (Out of View). SeeCoolingSystem on page 7!28.
J. Power Steering Fluid Reservoir (Out of View).SeePower Steering Fluid on page 7!38.
K. Brake Master Cylinder Reservoir. See“BrakeFluid”underBrakes on page 7!40.
L.Underhood Fuse Block on page 7!111.
M. Windshield Washer Fluid Reservoir. See“AddingWasher Fluid”underWindshield Washer Fluidonpage 7!39.
Engine Oil
Checking Engine Oil
It is a good idea to check the engine oil level at eachfuel fill. In order to get an accurate reading, the oil mustbe warm and the vehicle must be on level ground.
The engine oil dipstick handle is a yellow loop. SeeEngine Compartment Overviewon page 7!16for thelocation of the engine oil dipstick.
1. Turn off the engine and give the oil several minutesto drain back into the oil pan. If this is not done, theoil dipstick might not show the actual level.
2. Pull out the dipstick and clean it with a paper towelor cloth, then push it back in all the way. Remove itagain, keeping the tip down, and check the level.
7-17

5. If the fluid level is below the COLD check band,add only enough fluid as necessary to bring thelevel into the COLD band. It does not take muchfluid, generally less than one pint (0.5L). Do notoverfill.
6. Perform a hot check at the first opportunity afterthe transmission reaches a normal operatingtemperature between 160°F to 200°F (71°Cto 93°C).
7. If the fluid level is in the acceptable range, pushthe dipstick back in all the way, then flip the handledown to lock the dipstick in place.
Hot Check Procedure
Use this procedure to check the transmission fluid levelwhen the transmission fluid temperature is between160°F and 200°F (71°C and 93°C).
The hot check is the most accurate method to check thefluid level. The hot check should be performed at thefirst opportunity in order to verify the cold check. Thefluid level rises as fluid temperature increases, so it isimportant to ensure the transmission temperature iswithin range.
1. Locate thetransmission dipstick atthe rear of the enginecompartment, on thepassenger side of thevehicle.
SeeEngine Compartment Overviewon page 7!16for more information.
2. Flip the handle up and then pull out the dipstickand wipe it with a clean rag or paper towel.
3. Install the dipstick by pushing it back in all the way,wait three seconds, and then pull it back out again.
7-26

4. Check both sides of the dipstick and readthe lower level. Repeat the check procedureto verify the reading.
5. Safe operating level is within the HOT cross hatchband on the dipstick. If the fluid level is not withinthe HOT band, and the transmission temperatureis between 160°F and 200°F (71°C and 93°C), addor drain fluid as necessary to bring the level intothe HOT band. If the fluid level is low, add onlyenough fluid to bring the level into the HOT band.It does not take much fluid, generally less thanone pint (0.5L). Do not overfill.
6. If the fluid level is in the acceptable range, pushthe dipstick back in all the way, then flip the handledown to lock the dipstick in place.
Consistency of Readings
Always check the fluid level at least twice using theprocedures described. Consistency (repeatablereadings) is important to maintaining proper fluid level.If fluid is added, it may take 15 minutes or longer toobtain an accurate reading because of residual fluiddraining down the dipstick tube. If inconsistent readingspersist, check the transmission breather to be sure it isclean and not clogged. If readings are still inconsistent,contact your dealer/retailer.
7-27

If no coolant is visible in the surge tank, add coolantas follows:
1. You can remove thecoolant surge tankpressure cap whenthe cooling system,including the coolantsurge tank pressurecap and upper radiatorhose, is no longer hot.
Turn the pressure cap slowly counterclockwiseabout one full turn. If you hear a hiss, wait forthat to stop. A hiss means there is still somepressure left.
2. Keep turning the pressure cap slowly andremove it.
3. Fill the coolant surge tank with the proper mixtureto the FULL COLD mark.
7-33

4. At a wall, measure from the ground upward (A) tothe recorded distance from Step 3 and mark it.
5. Draw or tape a horizontal line (B) on the wall thewidth of the vehicle at the height of the mark inStep 4.
Notice:Do not cover a headlamp to improve beamcut-off when aiming. Covering a headlamp maycause excessive heat build-up which may causedamage to the headlamp.
6. Turn on the low-beam headlamps and place apiece of cardboard or equivalent in front of theheadlamp not being adjusted. This allows only thebeam of light from the headlamp being adjusted tobe seen on the flat surface.
7. Locate the vertical headlamp aiming screws, whichare under the hood near each headlamp assembly.
The adjustment screw can be turned with aE8 Torx®socket.
8. Turn the vertical aiming screw until the headlampbeam is aimed to the horizontal tape line. Turn itclockwise or counterclockwise to raise or lower theangle of the beam.
7-53

LED Lighting
The vehicle may have LED headlamps. Forreplacement of the LED lighting assembly contactyour dealer/retailer.
Back-Up Lamps
To replace this bulb:
1. Open the liftgate. SeePower Liftgateonpage 3!14for moreinformation.
2. Remove the twoscrews from thetaillamp assembly.
3. Pull the taillamp assembly rearward until youdisengage the inner pins on the taillamp assemblyfrom the vehicle.
4. Press the release tab, if the bulb socket has one,and turn the socket counterclockwise to remove itfrom the taillamp assembly.
5. Pull the old bulb straight out from the socket.
6. Press a new bulb into the socket, insert the socketinto the taillamp assembly and turn the socketclockwise into the taillamp assembly until it clicks.
7-55

7. Reinstall the taillamp assembly. When reinstalling,make sure to line up the pins on the taillampassembly with the vehicle. If you do not line up thepins correctly, you will not be able install thetaillamp assembly properly.
If you need to replace the taillamp, stoplamp, or turnsignal, you will need to see your dealer/retailer forservice.
License Plate Lamp
1. Remove the two screws holding each of thelicense plate lamps to the molding that is part ofthe liftgate.
2. Twist and pull the license plate lamp forwardthrough the molding opening.
3. Turn the bulb socket counterclockwise and pull thebulb straight out of the socket.
4. Install the new bulb.
5. Reverse Steps 1 through 3 to reinstall the licenseplate lamp.
Replacement Bulbs
Exterior LampBulb Number
Back-up Lamp7440
License Plate LampW5W
For replacement bulbs not listed here, contact yourdealer/retailer.
7-56